1-73 The gage pressure of the air in the tank shown in Fig. PI-73 is measured to be 80 kPa. Determine the differential height h of the mercury column. Oil 80 kPa SG = 0.72 75 cm Air Water 30 cm -Mercury SG = 13.6 h FIGURE P1-73

1-73 The gage pressure of the air in the tank shown in Fig. PI-73 is measured to be 80 kPa. Determine the differential height h of the mercury column. Oil 80 kPa SG = 0.72 75 cm Air Water 30 cm -Mercury SG = 13.6 h FIGURE P1-73

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.121P: One side of the container has a 03-m square door that is hinged at its top edge. If the container is...

See similar textbooks

Related questions

Q: A pilot notices that the barometric pressure outside his aircraft is 85 kPaa. The airport below the…

A: P1=100 kPa P2=85 kPa ρ(density)=1.15 kgm3 g=9.75 ms2

Q: 1-7. (a) Can two forces which are the components of the 200-lb force in Fig. Pl-7 intersect at B?…

A: Given: The force vector is shown below:

Q: A five Gallon container contains 60% water and 40% glycerin (specific gravity of 1.26). Determine…

Q: In the left-hand tank in Fig. 2-24, the air pressure is -9 in of mercury. Determine the elevation of…

A: Given:- The air pressure is -9 in of mercury. To Determine:- The elevation of the gage liquid in…

Q: 1.34 A piston/cylinder with a cross-sectional area of 0.01 m? has a piston mass of 65 kg plus a…

A: Given: Po = 101 kPa A = 0.01 m2 m = 65 kg F = 800 N Answer: P = 244700 Pa = 244.7 kPa So, to lift…

Q: 1-65 The maximum blood pressure in the upper arm of a healthy person is about 120 mm Hg. If a…

Q: Oil Water, machine oil and salty sea water are filling a pipe, as water shown on the figure. The…

A: Pascal's law Pascal's law (also Pascal's principle or the principle of transmission of…

Q: 1-108 A glass tube is attached to a water pipe, as shown in Fig. P1-108. If the water pressure at…

A: Guage Pressure: The pressure that is measured taking atmospheric pressure as reference is known as…

Q: 1-90 A hydraulic lift is to be used to lift a 1900-kg weight by putting a weight of 25 kg on a…

Q: A tank contains oil (s=0.80), gasoline (s=0.90) and water (s=1). What is the pressure at a depth of…

A: Step-1Given:- (SG)oil=0.80 (h)oil=0.50m (SG)gasoline=0.90…

Q: 1. Find the density of an oil filled in the liquid column as shown in figure. Given that absolute…

A: Given: Absoolute pressure at bottom P=500kPa Atmospheric pressure Patm=1.0132bar x=4m; y=4m; Z=1.5m…

Q: 1-74 Consider a U-tube whose arms are open to the atmo- sphere. Now water is poured into the U-tube…

A: Given Data The density of oil is 790 Kg/m3. Water at one end of height =0.70m the density of water…

Q: aan - 1.2 The radius and length of a steel cylinder are 40 mm and 110 mm, respec- tively. If the…

A: Given:Radius of cylinder base=R=40mm=0.04mLength of cylinder,H=110mm=0.11mMass density of…

Q: 1. Find the density of an oil filled in the liquid column as shown in figure. Given that absolute…

Q: A U-shape manometer connects to a water tank with the other end open as shown below. The specific…

A: The vertical height of the free surface above any point in a liquid at rest is known as pressure…

Q: 1. Find the density of an oil filled in the liquid column as shown in figure. Given that absolute…

Q: Kerosene Air 41 10 cm 21cm 9cm cm 15 cm Benzene Mercury Water

A: It is required to determine the pressure difference between A and B

Q: 1–75 Consider a double-fluid manometer attached to an air pipe shown in Fig. P1-75. If the specific…

Q: How much taller (in m) does the Eiffel Tower become at the end of a day when the temperature has…

A: Given Data;∆T=17∘ch=324mTo find change in its length.

Q: 1-33. An experimental test using human blood at T= 30°C indicates that it exerts a shear stress of T…

A: Shear stress at point A = 0.15 N/m^2 Velocity gradient = 16.8 sec^(-1) Find the apparent viscosity

Q: What is the air pressure (kpa) in a car tier? The pipe pressure is measured to be 20 kpa. For layers…

A: For same and continuous fluid pressure will be same for same horizontal level....

Q: A manometer is used to measure the pressure of a gas in a tank. The fluid used has a specific…

Q: 1-72 The maximum blood pressure in the upper arm of a healthy person is about 120 mmHg. If a…

Q: As shown in the figure, determine the gage pressure on the bottom of the tank in kPa Considering the…

Q: A gasoline line is connected to a pressure gage through a doubleU manometer, as shown in Fig. P2–86…

A: Given : Pgage = 370 kPa Density of water = 1000 kg/m3 The specific gravity of oil = 0.79 The…

Q: A 6 ft3 rigid tank contains 11 Ibm of water at 20 psia. Check Your Work zto.mheducation.com/hm.tpx…

Q: Consider a large cubic ice block floating in seawater. The specific gravity of seawater 1.05. If a…

Q: 3. THE SYSTEM IS 20C. IF ATMOSPHERIC PRESSURE IS 101.03 KPA AND ABSOLUTE PRESSURE AT THE BOTTOM IS…

A: Given dataAtmospheric Pressure = 101.03 kPaAbsolute pressure at the bottom = 231.3 kPaWe have to…

Q: 4. Determine the pressure difference between the points at A and B. Take the density of air as…

A: Answer: ( PA - PB ) = 63.7662 kPa.

Q: 1. Find the density of an oil filled in the liquid column as shown in figure. Given that absolute…

Q: 1-64 Both a gage and a manometer are attached to a gas tank to measure its pressure. If the reading…

Q: 1-7. (a) Can two forces which are the components of the 200-lb force in Fig. Pl-7 intersect at B?…

Q: 1-50 The water in a tank is pressurized by air, and the pressure is measured by a multifluid…

A: Given Data g=9.8 m/s2 h1=0.2 m h2=0.3 m h3=0.4 m density of water is 1000 Kg/m3 Density of oil is…

Q: Q1/ The gauge pressure of the air in the tank shown in (Fig.1) are measured to be 80 kPa. Determine…

A: The differential height of the mercury column: h = 0.582 m

Q: how many meters is the water height in the manometer?

A: In this question, differntial pressure is given as 1in 20 atmospheric pressure which is not so…

Q: 1-75 Consider a double-fluid manometer attached to an air pipe shown in Fig. P1-75. If the specific…

A: Given dataPa=76 KPaSg1=13.55Pair=100 kpaTo find Sg2

Q: 1.9 Both a gage and a manometer are attached to a gas tank to measure its pressure. If the reading…

A: Given data: Pg=80 kPaρHg=13600 kg/m3ρw=1000 kg/m3 Need to determine the distance between the two…

Q: 2-98 Three forces are applied with cables to the anchor block shown in Fig. P2-98. Determine b. The…

A: Given: The forces are: F1=272 NF2=500 NF3=650 N

Q: Given: Figure as shown below: density of water = 62.3 lb/ft3 specific gravity of mercury = 13.60 ss…

A: The absolute pressure at any point can be calculated by the formula stated below as- Pabs=ρgh+Patm…

Q: 5. Determine the pressure difference between point A and B using the following Specific Gravity:…

A: It is required to determine the pressure difference between A and B

Q: 5. Determine the pressure difference between point A and B using the following Specific Gravity:…

A: It is required to determine pressure difference between A and B

Q: A pilot notices that the barometric pressure outside his aircraft is 85 kPaa. The airport below the…

Q: 1-53 The water in a tank is pressurized by air, and the pres- sure is measured by a multifluid…

A: Given figure The water in a tank is pressurized by air, and the pres sure is measured by a…

Q: 13,600 kg/m) is con- 1-72 A mercury manometer (p = nected to an air duct to measure the pressure…

A: Note:As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: Q1- Consider a large cubic ice block of (1 m) surface area floating in seawater. The specific…

Q: 1-90 A hydraulic lift is to be used to lift a 1900-kg weight by putting a weight of 25 kg on a…

A: NOTE -: Under the guidelines, we experts cannot include names in the answer.

Q: 5. Determine the pressure difference between point A and B using the following Specific Gravity:…

A: GIVEN DATA- A DIFFERENTIAL MANOMETER GIVEN WE HAVE TO FIND PRESSURE DIFFERENCE BETWEEN A AND B

Q: The pressure inside a competion grade tennis ball is 1.6 times higher than the atmospheric pressure.…

Q: A manometer is used to measure the pressure of a gas in a tank. The fluid used has a specific…

A: Given:Specific gravity of fluid in the manometer, s=0.85height of fluid in manometer column, h=55…

Q: Determine the gage pressure in kPa at point "a", if the liquid A has a SG = 1.20 and liquid B has SG…

Concept explainers

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.

Question

1-73 The gage pressure of the air in the tank shown in Fig.
PI-73 is measured to be 80 kPa. Determine the differential
height h of the mercury column.
Oil
80 kPa
SG = 0.72
75 cm
Air
Water
30 cm
-Mercury
SG = 13.6
FIGURE P1-73

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.
Consider the system shown in Fig. P1-77. If a change of 0.7 kPa in the pressure of air causes the brine-mercury interface in the right column to drop by 5 mm in the brine level in the right column while the pressure in the brine pipe remains constant, determine the ratio of A, /A,. Air Area, A₁ Water Mercury SG 13.56 Brinc pipe SG= 1.1/ Area, A₂
In the figure, fluid 2 is carbon tetrachloride(1.589) and fluid 1 is benzene (SG = 0.877). If the atmospheric pressure is 101.5 kPa, determine the absolute pressure at point A. Patm fluid 1 35cm 12 cm fluid 2 Fig. 2-26 Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: kPa abs
A 98.43ft vertical column of fluid (density is 1878 kg/m3) is located where is 31.66ft/sec2. determine the pressure at the base of the column in kPa.
Determine the pressure difference between points C and D. Take the specific weights to be Benzene: 8640 N/m³, Mercury:133100 N/m³ Kerosene: 7885 N/m?, Water: 9790 N/m2, Air: 12 N/m³. Water Benzene Air D 50 cm 19 cm 30 cm 24 cm $18 cm Mercury Kerosine (answer) Pa
A manometer is used to measure the pressure of a gas in a tank. The fluid used has a specific gravity of 0.85, and the manometer column height is 55 cm, as shown in Fig. 1-56. If the local atmospheric pressure is 96 kPa, determine the absolute pressure within the tank.
The height of the fluid inside the tube after immersion is 1⁄8 the height of the cylinder glass tubing. It was immersed into a tank of a cleaning solvent with specific gravity of 0.83. The remaining length of tube above the surface is 6 cm. Determine the length of the tubing with an inside diameter of 4cm. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: m
3-49 The pressure difference between an oil pipe and water pipe is measured by a double-fluid manometer, as shown in Fig. P3-49. For the given fluid heights and specific gravities, calculate the pressure difference AP = PB – PA: Glycerin SG = 1.26 Water SG = 1.0 Oil SG = 0.88 %3D 60 cm 10 cm B 15 cm 20 cm Mercury SG = 13.5 اضف ملف ک
3-55 Consider a double-fluid manometer attached to an air pipe shown in Fig. P3-55. If the specific gravity of one fluid is 13.55, determine the specific gravity of the other fluid for the indicated absolute pressure of air. Take the atmospheric pressure to be 100 kPa. Answer: 1.34 Air P = 76 kPa 40 cm SG2 22 cm SG = 13.55
3-47 Two chambers with the same fluid at their base are separated by a pistan whose weight is 25 N, as shown in Fig. P3-47. Calculate the gage pressures in chambers A and B. FIGURE P3-43 Piston 344E Twa eil tanks are connected to each other through a manometer. If the difference between the mercury levels in Air p Air Oil Oil 50 em 10 in 30 cm 25 cm E. 30 cm 32 in Water CMereury 50 c FIGURE P3-44E FIGURE P3-47 108 FLUID MECHANICS 3-50 Consider the system shown in Fig. P3-50. If a change of 0.7 kPa in the pressure of air causes the beine mercury interface in the right column to drop hy 5 mm in the hrine level in the right column while the pressure in the brine pipe remains coustant, determine the ratio of AJA, 3-48 Consider a double-fluid manometer attached to an air pipe shown in Fig. P3 48. If the specific gravity of ene fluid is 13.55, determine the specific gravity of the other fluid for the indicated absolute pressure of air. Take the atmospheric pressure to be 100 kPa. Answer: 5.0…
Determine the pressure difference between points C and D. Take the specific weights to be Benzene: 8640 N/m?, Mercury:133100 N/m? Kerosene: 7885 N/m³, Water: 9790 N/m², Air: 12 N/m³. Water Benzene, Air D C 50 cm 19 cm 30 cm 18 cm 24 cm ст Mercury- Kerosine (answer) Pa
Please solve and show your solution on a paper with units in every proceedure. Determine the vertical pressure in kgf/cm2 due to a column of water 70 m high.