please solve with neat hand writing so I can understand 1) The steel tube in the system below has an outside radius as listed and an inside diameter of 175mm.The tube is 2.5m tall. What is the axial deformation in the tube?500 kN100 mm01_PROB_82- Find the E of steel in the book.- Calculate the cross-sectional area of the tube.- Solve for the normal stress in the tube.- Use Hooke's Law to solve for the strain in the tube.- Solve for the deformation with a modified strain equation.- Compare your answer: Axial deformation is about -0.849mm

Answered: Image /qna-images/answer/37ba3717-1e5c-4cec-8dc2-fc2ab6801ef7.jpg

Answered: 1) The steel tube in the system below…

1) The steel tube in the system below has an outside radius as listed and an inside diameter of 175mm. The tube is 2.5m tall. What is the axial deformation in the tube?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.1P: A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the...

See similar textbooks

Related questions

Q: Problem 2 Consider a plate formed by a homogeneous material with Young's modulus E, and Poisson's ra...

A: Stiffness matrix In the limited component technique for the mathematical arrangement of elliptic fra...

Q: A light fixture of negligible mass, has three applied forces acting on it as shown. |F,| = 4 kN 1.2 ...

A: Find the magnitude of reactive force at point O

Q: A car is moving ight roud at dce leration at 8 m/s what r6 secando ! on a 18 m/s it is will be its v...

A: Given data : The initial velocity of car=U U=18 m/s The value of acceleration=a a=8 m/s2 The value o...

Q: A force of 10 lb is applied to the cord. Block A weighs 23 lb. Neglect the mass of the pulleys and c...

Q: w. How much effort must be applied?

A: To find applied effort.

Q: Using the coordinate system shown, determine the moment created by the Force F3 about the point 0. M...

Q: Which of the following systems is designed toreduce NOx and has little or no effect on overallengine...

A: Given Data : NOx

Q: In Gotham City, the departments of Administration (A), Health (H), and Transportation (T) are interd...

A: the transportation problem as shown below

Q: 1a.Explain briefly why crude oil is refined to its finest products. 1b. Explain biomass is considere...

Q: A supply chain is a series of activities from supplier to customer that adds value to a product or s...

A: True.

Q: Advanced hybrid materials technology has been used in automotive applications. A good example is eng...

A: Hybrid composite materials are employed in a variety of engineering applications due to their div...

Q: Encontrar la tensión o compresión de cada varilla si el peso que tiene que soportar es de P=10KN 2 V...

A: tanθ=31/2/1 θ=60° Calculating reactions at A and D, sum of horizontal forces along X direction = 0 H...

Q: An elastic body is subjected to a tensile stress X in a particular direction and a compressive stres...

Q: Investigate which problem can be solved by the two-dimensional stress distribution 011 = 4x1x2; 012 ...

A: according to the given details,

Q: The LiBr-water absorption cycle shown in Fig. 17-2 operates at the following temperatures: generator...

A: Find the concentration of Li-Br in the generator Tg=100°C Tc=55°C Te=10°C Ta=30°C

Q: A light fixture of negligible mass, has three applied forces acting on it as shown. 1. |F,| = 4 kN 1...

Q: 4. Two and one-half pounds of air actuate a cycle composed of the following processes: polytropic co...

Q: A skier starts from rest on the 45° slope at time t = 0 and is clocked at t = 2.64 s as he passes a ...

Q: KE of the flywheel

A: A circular solid disc of uniform thickness, t =25mm Radius of the disc, R=225 mm Mass, m =25 kg It r...

Q: -0 Mlores thacugh a 28omm djametcr friction factor, (F)=0.0225 of Sengih (L)= 580m.Volumetric flow r...

A: GIVEN DATA - D=280mm=0.28m L=580mm f=0.0225 Q=0.3 m3/s WE HAVE TO FIND HEAD LOSS DUE TO FRICTION

Q: If the Poisson's ratio of an elastic material is 0.6 the ratio of modulus of rigidity to Young's mod...

Q: Determine the coordinates of the end point of the [T2 4] direction and the intercepts of the (212) p...

A: Givendirection 1,2,4palne 2, 1,2

Q: Zinc hasthe hexagonal close-packed crystal structure. The lattice parameters for zinc are a = 0.2664...

A: Lattice Parameter: It is defined as the distance between centers of the neighboring corner atoms. Cr...

Q: Which of the following is the motion of objects moving in two dimensions under the influence of grav...

A: Answer = option(d)

Q: Express the boundary conditions on each boundary for each problem shown below. y

A: To find Boundary conditions

Q: A bus travels with a speed of 20 m/s when accelerated at 0.16 m/s from its rest position. What is th...

A: Calculated the distance travelled by bus.

Q: Consider the same problem in which an axial compressor with a mean diameter of 0.8 m is being design...

Q: (mechaniam structure and preloaded structure). [Fill the table gives below). of the systems shown in...

Q: Which invariant reaction can be recognized in 2300 210 1900 1700 1500 1300 Temperature, "C (A)

A: the peritectic reaction can be easily recognized in the phase diagram.

Q: (Q-2) Estimate the thermal conductivity of liquid acetone in (Btu/hr.ft.F ),at (25 given; Isothermal...

Q: By itself, the 2700-kg pickup truck executes a 0–98 km/h acceleration run in 11.0 s along a level ro...

Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown...

A: given; lets take reaction force at A=RAlets take reaction force at C=Rca=11ftb=5ftw=11.5kips/ft

Q: 2. Show that the gravitational self-energy (energy of assembly piecewise from infinity) 3GM? of a un...

Q: - A rectangular plate simply supported along its edges and subjected to a uniform of intensity po: 1...

A: Givenuniform load =Pob=2aw=0.01013

Q: the output speed in rpm is

A: Given; The following are the data for two crossed helical gears used for speed reduction; Gears 1: P...

Q: Displacement of a body is a quantity. * O scalar vector O scalar and vector none of the mentioned

A: Vector has magnitude and direction. Scalar has only magnitude.

Q: The two wires are connectec at A. If the force P causes point A to be dsplaced horizontally 2 mm, de...

A: To determine the normal strain in each wire.

Q: QUESTION 5 Knowing that the tension in cable AC is 1065 N, determine the moment about each of the co...

Q: In the set-up shown, a rectangular gate, ABCD, is used to store layers of oil and water. The weight ...

A: Givenweight of the gat w=4kNforce exerted by the stopper on the gate F=30kN

Q: A round solid cylinder made of a plastic material (a = 6 × 10-7 m³/s) is initially at a uniform temp...

A: (a) We consider a control volume (CV) and study the heat transfer from and to this CV in a short ti...

Q: the furnace to build the chimney top are provided in Section B-B 16. Regarding wood framing, A. head...

A: “Since you have asked multiple question, we will solve the first question for you. If you want any s...

Q: The maximum interference (in microns) in the assembly is

A: Given data; In an interchangeable assembly, Shaft size= 25.000+0.040-0.010mm Hole size=25.000+0....

Q: The second moment of area about the centroidal axis [Irx] for the rectangular section shown in the f...

Q: the ratio of modulus of rigidity to Young's

A: Given; Poisson's ratio=0.8Find ratio of modulus of rigidity to Young's modulus ?

Q: open cycle gas turbine employs a regenerative arrangement. The air enters the compressor at 1 bar an...

Q: n. What is the force necessary to stop the 0.14 kg

A: To find the force.

Q: Q1. A spur gear train with a speed reduction of 3:1 is to be used in a sugarcane crusher. A single c...

A: ear ratio = G= 3 speed of pinion = Np= 720 rpm speed of gear= Ng= 720/3 = 240 rpm Power = P= (Q+5)= ...

Q: 1. Determine the reactions exerted by the fixed support (A) on the beam shown in Figure 1. 30 N A 50...

Q: In crank and slotted lever quick return mechanism, the crank length is (100 +X )mm and the distance ...

A: consider reg. no. of the student is 11912081 then X=81 crank length= 100 +X = 100 + 81 =181 mm fixe...

Q: Q3. Swimming robots – Two friends, Alex and Barbara, are having a friendly competition: who can buil...

A: Paddle wheels are good for high viscosity fluids and propeller are good for high speed in low viscos...

Concept explainers

Layout

The layout is a way of organizing the elements, products, and raw materials in a design. The layout is the representation of information in a structural, logical, descriptive, coherent form.The layout is a mapping of various equipment arrangements, workstations, machinery, plants, and more. It secures the continuous movement of a product quantity along with the quality.

Question

please solve with neat hand writing so I can understand

1) The steel tube in the system below has an outside radius as listed and an inside diameter of 175mm.
The tube is 2.5m tall. What is the axial deformation in the tube?
500 kN
100 mm
01_PROB_82
- Find the E of steel in the book.
- Calculate the cross-sectional area of the tube.
- Solve for the normal stress in the tube.
- Use Hooke's Law to solve for the strain in the tube.
- Solve for the deformation with a modified strain equation.
- Compare your answer: Axial deformation is about -0.849mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
The stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.
A specimen used in a coupon test is shown in the figure. The stresses on element A are known to be sy= -1500 psi. Use Mohr’s circle to: (a) Find the stresses acting on the element oriented at an angle ?? = -35°. (b) Find maximum normal and shear stresses and show them on sketches of properly oriented elements.
A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
(a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressure
- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clement
An element in plane stress on the fuselage of an airplane (figure part a) is subjected to compressive stresses with a magnitude of 42 MPa in the horizontal direction and tensile stresses with a magnitude of 9.5 MPa in the vertical direction (sec figure part b). Also, shear stresses with a magnitude of 15.5 MPa act in the directions shown. Determine the stresses acting on an element oriented at a clockwise angle of 40g from the horizontal. Show these stresses on a sketch of an element oriented at this angle.
In the picture there is a sketch of a socket wrench. Assume the wrench is held at a fixed point “A”. The yield stress of the material is known to be 400 MPa. Answer the questions below Describe the stresses at point “A” and their causes and calculate the stresses. Determine the factor of safety against yield assuming the Tresca yield criteria. Determine the factor of safety against yield assuming the von Mises yield criteria using both principal stresses and “Cartesian” stresses. Do your values match or not, and is this expected? Explain. Do the calculated values make sense with the respect to the Tresca value? Explain, why or why not?