I need the answer quickly Q5/ answer the following questions :1- Which type of instruction dose INTO normally follow? Which flag does is test?2- In a minimum-mode 8086 microcomputer, which signal indicates to external circuitry thatthe current bus cycle is for the 1/0 interface and not the memory interface?3- Which type of I/0 has the disadvantage that all 1/0 data transfers must take place throughthe AL or AX register?4- How many bytes of memory does an interrupt vector take up?5- In a maximum-mode system, which device produces the input (read), output (write), andbus control signals for the 1/O interface?6- How many address lines must be decoded to generate five chip select signals?7- What do you mean by pipelined ?8- Draw the register organization of 8086.9- At what address are CS40 and IP40 stored in memory?

The signals that are directly available from the devices are analog. Hence a conversion is required…

Answered: 1- Which type of instruction dose INTO…

Engineering

Electrical Engineering

1- Which type of instruction dose INTO normally follow? Which flag does is test?

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Related questions

Q: 1. Are the theoretical calculations and measured values are equal? Explain?

A: Resistors, inductors and capacitors form an integral part of any electrical circuit. A source,…

Q: Given the image below, what are the control signals needed to perform the NOT operation (OR (x, y)).

A: The control signal needed to perform the NOToperation (OR(x,y) ) are:Since,zx =1, then x = 0, the…

Q: What will happen to the output (light) if you use the XIC instruction associated with a normally…

A: XIC instruction is associated with Programmable Logic Controllers (PLC) and used in ladder logic…

Q: ‏List the flags that would be affected during the use of IN instruction.

A: In this question we will know about the flags that would be affected during use of instruction....

Q: Describe DCS and PLC control systems.

A: This question is from control system.

Q: Question: 1:- What is the advantage of the adding a Lag controller for the SS model?

A: Since you have asked multiple questions in a single request, we will be answering only the 1st…

Q: Explain different types of ADC with figures?

Q: Answer the following briefly. 1- Describe control objectives for a process control.

A: Since you have asked multiple question ,we will slove the first question for you .If you want any…

Q: (i) With neat sketch explain the dynamic turn OFF characteristics of the device which is used in…

A: A SCR (thyristor) is the device used in high power applications. Before learning about the turn off…

Q: List three factors that would contribute to a variation between calculated and measured values.

A: There is various factors which contribute to cause in measured value . Fualty equipment Wrong…

Q: Refer to the exhibit. In which section of the motherboard would a SATA cable would be installed? D…

A: SATA ports on the motherboard are commonly positioned away from all of the other ports. SATA ports…

Q: What was the first electrical digital computer comprised of?

A: All latest computers today are digital computers. An electronic digital computer uses electricity…

Q: 21. Which voltage range that is sometimes called a “float" in TTL circuits?

Q: What value should come to the cell indicated by A2 when the Routh table of the control system given…

A: Using the Characterstic equation for routh hurthwiz Find A2 in given table?

Q: 1- Is the Gray code arithmetic code? Why? Where this code used?

Q: What is

A: Given: The NEC Article 430 is shown as:

Q: Briefly explain the operation of a counter controlled ADC

Q: From what location are the first computer instruction ?available on boot up

A: using the bootup process one can make it ready to use by putting in the instructions which it needs…

Q: What is Adaptive control system? If the process characteristics are not well known then what type of…

A: Adaptive control system is the control method which is used by a controller and which must adapt to…

Q: In which areas/fields can ICs be used?

A: Integrated circuit is abbreviated as IC These are also known as micro chips as they are very small…

Q: In what situation we cannot select both current and voltage references randomly? Why?

Q: a.What is an ROC?

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: Briefly explained the function of the hold device in a digital control system.

A: The hold device is used to convert discrete signal into continuous or analog signal which can be…

Q: Basic Control Actions 1) What is the most used controller?

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: What are the risks associated with NOT implementing ISO 27001 in an organization ? What are some…

A: ISO 27001: It provides a standard framework to manage information and data for a modern…

Q: 1. How will you check? And what instrument will you use to determine whether the power supply is…

A: According to our policy we can provide solution. For other solutions repost the questions with…

Q: 15. Upon exiting Reset, which instruction is first executed?

A: Explanation: After the hardware reset, the CPU will start execution at the physical address 0xFFFF0.…

Q: What will be displayed on the displays?

Q: writ Overview about LED brightness control?

A: A light-emitting diode (LED) is a semiconductor device that emits light through which electricity…

Q: I opened a broken Coin Pusher Arcade game to fix, and I saw a burned IC. Between Microprocessor and…

A: An arcade game is a game machine which usually found in public places like malls, restaurants and…

Q: List the flags that would be affected during the use of IN instruction.

A: The IN instruction is a kind of mnemonic which is used for the input in microprocessor. It input the…

Q: Describe the process for controlling maintenance requests. Should all requests be handled in the…

A: Maintenance is a basic part of every system or any operational thing because they need maintenance…

Q: Draw the block diagram of a CPU showing the basic units. Explain the functions of each unit shortly.

Q: · Explain the meaning of terms (Accuracy and Precision) and give example for an each?

A: Accuracy:- Accuracy is defined as the "closeness" to the true value.So, an instrument is said to be…

Q: How do the different parameters vary with ic?

Q: Which button is used to run the simulation in LTspice program?

A: LTspice program: It is a high performance simulation (SPICE) software. It is used to design a…

Q: 4. Explain the process of sample and hold?

A: Since you have posted the multiple questions so we are supposed to answer the 1st one.

Q: Explain the function of the common control block when used with the standard graphic symbols.

A: The control blocks are present in the PLC control system for added functionality in the system. The…

Q: Design the hardwired control unit using sequence counter method for 8 instructions. Consider 2…

A: We need to design the hardwired control unit using sequence counter method for 8 instructions.…

Q: What is the name of the wires that connect the memory?

A: Memory: Memory serves as the computer's electrical storage facility for the instructions and data…

Q: Explain Several design decisions exist with regard to instruction sets?

A: A set of native instructions that can only be carried out by hardware are defined by an instruction…

Q: Can you create a concept map using these information?

A: We need to draw the concept map by using the given information.

Q: 1) The Execute Unit (EU) functions? 2) Compare between status & control flags?

A: In this question , we will write about execute unit, status flag and control flag..

Q: What is the difference between an LEA SI,NUMB instruction and a MOV SI,OFFSET NUMB instruction?

A: An instruction of a computer is a command given to the computer to perform a specified operation on…

Q: Following error

Q: What is NEC and what is the purpose of it? Does it present the maximum standard or the minimum?

A: NEC stands for National Electrical Code and it provides some basic standards and requirements which…

Q: What is the difference between a one function and a multifunction electronic control device

A: A one function electronic control device operate only one function, Those equipment which uses…

Question

I need the answer quickly

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

4) Design and draw these memory units with their control circuits. Explain operations. a) A single EPROM 2716 is used with an 8088 microprocessor so that this microprocessor will see only X bytes of memory between the address range of DF800 –DFFFF or DD800 - DDFFF instead of 1M byte that it expects. Draw this circuit. What are X bytes? Do not use 74138 decoders. b) Design and show a 16K x 16-bit memory circuit by using 8K x 8-bit RAMS. Explain its operation. Do not use decoder 74138 chip.
1. Draw the figure showing the types of registers in an 8086 microprocessor. Write the register group types explaining the functions shortly for each one.
Pipelining in 8086 processors is achieved using which of the following option: O a. By using the counting register CX that acts as counter for LOOP instruction. O b. By using the 6-byte instruction queue that stores pre-fetched instructions while one instruction is being executed. O c. By using accumulator AX, that stores the result of multiplication operation. O d. By using the adder of the Bus Interface Unit that converts logical address to physical address.
8085 microprocessor went through its manipulation operation in the ALU, the results was transferred on the data bus and status of the results was stored in the flag register for indications . With your knowledge and understanding illustrate a complete bit configuration of 8085 flag register and show the functions of the represented bits in the register.
B) Name the internal registers of 8086, Table the combination of registers to form the physical addresses for memory segments.
4. Write a simple complete program with LOOP instruction for 8086 microprocessor, and explain the processes for each line of the program.
a.Write the addressing modes of the following instructions: (i) MOV A, @R0(ii) MOVX @DPTR, A (iii) MOVC A, @A+DPTR (iv) MOV R0, #45H b) Write instructions to perform the following operations: (i) Move the content of Accumulator to register 7(R7).(ii) Move the contents of RAM memory location 55H to Port 1(iii) Receive content from ROM Memory location 200H into Accumulator.(iv) Clear bit 7 of the Accumulator.c) Why 4-20mA Current loop is widely used Industrial Standard for sensor data transmission and control. What are its advantages over 0-12V Standard? d) Two configurations of GPIB is shown in Fig. A and Fig. B. Explain the working of GPIB in both the configurations and what are the differences between the two. this question is asked in microcontroller and microprocessor
P Flag question Explain the MUL instruction of 8086. Compare it with IMUL instruction. (1 +1 Marks) Write a Assembly language program for 8086 to find the cube of a number using MUL instruction. (5 Marks) (Note : Solve the question in paper, scan and upload along with the other Part B and C answers) B I III
1. How do the data retention characteristics of RAM and ROM storage devices differ? 2. What is the purpose and use of the Program Counter (PC), Stack Pointer (SP), and Memory Address Register (MAR) registers? 3. Write an 8085 program to store 4EH in memory location 2840H and store 3EH in memory location 2841H, exchange them and store the result in memory locations 2842H and 2843H respectively. Solve this problem using three different methods. 4. Write a program to exchange the content of memory locations [2801] [2800] with [2803] [2802]. 5. The following program is supposed to add the contents of memory location 2050h to the Accumulator. The program works correctly only part of the time. Show that it is wrong to execute the program and how to correct it. MOV LDA ADC HLT В.А 2050H в 6. In a multibyte addition program, when you must use the ADD instruction? When you must use the ADC instruction? 7- The 8085-instruction set does not include a clear accumulator instruction. Which…
Q. 1 There are different types of memories used in 8086 microprocessor one of them is called Stack. You are expected to investigate about it and answer the following questions related to it. i. What is stack memory? ii. What registers are associated with the stack in 8086? (including segment, pointer registers) iii. What is the use of stack? iv. Use any example which uses stack memory with appropriate instructions (PUSH, POP)
Memory interfaced to 8086 Microprocessor 16 data bus should be arranged in-------- a.One bank. b.Two bank c.Three bank. d.Four bank JC mean jump to specific address when the CF in the flag bit is = a. zero b.two c.one d.three Overflow flag bit indicates overflow for a.Signed integer only. c. Signed and Unsigned integer only. The 8086 architecture consists pipeline processing. b. Two b. Three arithmetic operations. b. Unsigned integer only. d. Floating point. unit(s) work in parallel is called c.Four d.One
Draw the figure for memory segments with 8086 microprocessor software model. Explain the logical address structure used for each segment (Explain which registers are used in logical address presentation of each segment; segment address : offset address). Give an example solution to find the physical address in a segment from the logical address for 8086 microprocessor.