1. A 125 x 95 x 10 mm angle is welded to a frame by two 10 mm fillet welds, as shown in Fig. 1. A load of 16 kN is apsplied normal to the gravity axis at a distance of 300 mm from the centre of gravity of welds. Find maximum shear stress in the welds, assuming each weld to be 100 mm long and parallel to the axis of the angle.

1. A 125 x 95 x 10 mm angle is welded to a frame by two 10 mm fillet welds, as shown in Fig. 1. A load of 16 kN is apsplied normal to the gravity axis at a distance of 300 mm from the centre of gravity of welds. Find maximum shear stress in the welds, assuming each weld to be 100 mm long and parallel to the axis of the angle.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q.2. A bar with a rectangular cross-section is weld as shown. Determine the size weld, if the pemissible shear stress in the weld 80 MPa. The rectangle area of a fillet weld is equal to [ 2t (b+/)]. 31KN Please send the solution within half an hour and thank you
1. A 125 × 95 × 10 mm angle is welded to a frame by two 10 mm fillet welds, as shown in Fig. 1. A load of 16 kN is apsplied normal to the gravity axis at a distance of 300 mm from the centre of gravity of welds. Find maximum shear stress in the welds, assuming each weld to be 100 mm long and parallel to the axis of the angle. 16 KN 300- G 125 100- All dimensions in mm. Fig. 1
A 1/4 in fillet weld is to transmit a total force of 12,000 lb. If the allowable unit stress in shear on the weld is 15,800 psi, the minimum effective length of the weld must be A. 5.4 B 4.9 in C. 4.3 in D 3.9 in.
8) A plate 75 mm wide and 10 mm thick is joined with another steel plate by means of single transverse and double parallel fillet welds as shown in Fig.3. The joint is subjected to a maximum tensile force of 55 kN. The permissible tensile and shear stresses in the weld material are 70 and 50 N/mm2 respectively. The length of each parallel fillet weld is: 55 kN 55 kN Fig.3 O 25.29 mm 40.58 mm O 64.77 mm O97.58 mm 75 mm
A cylindrical pressure vessel has an outside diameter of 1.5 meters, and a length of 5 meters. The vessel is made of steel with butt-welded seams and is 10 mm thick. The seams form an angle of 25 degrees with a plane perpendicular to the long axis, as shown. The allowable normal stress perpendicular to the weld is 150 MPa. The allowable shearing stress parallel to the weld is 80 MPa. What is the allowable gage pressure? Use (and draw) Mohr's circle. 25
A cylindrical pressure vessel 4 ft in diameter is welded using a spiral seam that makes an angle of 30° with respect to a transverse plane of the cylinder, as shown below. For an internal pressure of 180 psi and a wall thickness of 3 in, determine (a) the normal stress perpendicular to the weld, and (b) the shearing stress parallel to the weld. 30%
A rectangular steel plate is welded as a cantilever to a vertical column and supports a single concentrated load P. Determine the weld size if shear stress in the same is not to exceed 140 MPa
Q1. A plate b mm wide and t mm thick is joined with another plate by a single transverse and a double parallel fillet weld as shown in Fig. if the permissible tensile and shear stresses in the weld material are otw MPa and tw MPa respectively and the permissible tensile stress in the plate material are otp MPa, Find the length Li of single transverse fillet weld, if the joint is subjected to both static and fatigue loading. All dimensions in mm.
A circular shaft of diameter 120 mm is welded to a rigid plate by a fillet weld of size 6 mm. If a torque of 8 kNm is applied to the shaft, what is the maximum stress in the weld?
1. A butt weld is set on the cross section of an I-shaped beam. There are bending moment M and shear force V at the splicing position, where M=1120 kN•m and V= 374 kN. The beam is made of Q355b steel and semi-automatic weld is used with welding rod E50. The design value of the weld tensile strength f," is 260 N/mm². Please check whether the strength of the butt weld is safe by calculation. 280 M M 0001
10. Two tie bars are connected together by 0.5cm fillet welds around the end of 1 bar and the inside of a slot machined in the same bar. Estimate the strength of the connection in tension if the shearing stress in the welds is limited to 75MPa. 450m 10cm 8cm
Solve Q7 only 4) A welded connection, as shown in Fig. 2, is subjected to an eccentric force of 60 kN in the plane of the welds. Determine the size of the welds, if the permissible shear stress for the weld is 200 N/mm2. 60 kN W3 100 W2 -150 50 Fig. 2 7) What is the value of polar moment of inertia of all welds about C.0.G? 3890094.64 mm4 4528724.56 mm4 6782459.89 mm4 9875612.79 mm4