1. A clock signal is usually a continuous triangular wave that serves as another hput to a memory element. 2. In an edge-triggered flip-flops, a positive edge-triggered is ON if there is a change from O to 1 and OFF in all other times. 3. In an edge-triggered flip-flops, a negative edge-triggered is ON if there is a change from 1 to 0 and ON in all other times.

1. A clock signal is usually a continuous triangular wave that serves as another hput to a memory element. 2. In an edge-triggered flip-flops, a positive edge-triggered is ON if there is a change from O to 1 and OFF in all other times. 3. In an edge-triggered flip-flops, a negative edge-triggered is ON if there is a change from 1 to 0 and ON in all other times.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Problem Statement: You design a circuit of a decade counter that will count from 0-9 only. You will only be using the following: (a) Button – only 1 button will be used to trigger the counting. (b) Flip flop IC to used as counting circuit with 4 - BITS binary OUTPUT. (c) IC's for Decoding the Binary OUTPUT of Flip-flops to Decimal Output (d) 7- Segment Display to display the OUTPUT from 0-9. Block Diagram: 4 Bit Binary Flip-Flop 7-Segment Display Button Decoder Circuits Circuits
(c) For each of the following parts, fill in the respective row of the timing diagram shown in Figure 5. (i) Find the input for a rising-edge-triggered D flip-flop that would produce the output Q as shown in Figure 5. (ii) Find the input for a rising-edge-triggered T flip-flop that would produce the output Q as shown in Figure 5. Clock D Figure 5
Construct a 4-bit Johnson counter using J-K flip-flops. (See Figure 12-12 for a Johnson counter.) What sequence of states does the counter go through if it is started in state 0000? State 0110?
(d) Figure 6 shows the diagram of a 3-bit ripple counter. Assume Qo = Q1 = Q2 = 0 at t = 0, and assume each flip-flop has a delay of 1 ns from the clock input to the Q output. Fill in Qo, Q1, and Q2 of the timing diagram (shown in Figure 7). Flip-flop Q1 will be triggered when Qo changes from 0 to 1. %3D 3 Qo Q2 T T Clock- Figure 6 Clock 10 15 20 25 30 35 40 45 50 Figure 7
1.) A storage register made up of six D flip-flops is storing a binary word. The flip-flop status are: A = set, B = set, C = reset, D = set, E = reset, and F = set. The A flip-flop is the LSB. The decimal equivalent of the register content is 2.) D flip-flops are most frequently used in
Which one is true for D flip flop? a) It has 2 inputs 1 output b) It has always the output 1. c) The output of it will be equal to its' input. d) It can not be used in logic circuit designs.
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
16. The following serial data are applied to the flip-flop through the AND gates as indicated in Figure 7-85 Ⓒ. Determine the resulting serial data that appear on the Qoutput. There is one clock pulse for each bit time. Assume that Q is initially 0 and that and PRE are HIGH. Rightmost bits are applied first. J₁: 1010011; J₂:0111010; J: 1111000; K: 0001110; K 1101100, K: 1010101 CLK K₁ CLR Figure 7-85 C K PRE -Q CLR
(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).
In a 4-bit ripple up-counter how many clock pulses will you apply, starting from state 0 0 0 0, so that the counter outputs are as follows? (a) 0010 (b) 0111 (c) 1001 (d) 1110
What is the type of the flip flop? Why? Next state Present state output output delay b.
show the waveforms for each flip-flop output with respect For the ring counter in Figure to the clock. Assume that FF0 is initially SET and that the rest are RESET. Show at least ten clock pulses. D D. FFO FF1 FF2 FF3 FF4 FF5 FF6 FF7 FF8 FP9 CLK