1. A company produces machine components which pass through an automatic testing machine. 5% of the components entering the testing machine are defective. However, the machine is not entirely reliable. If a component is defective there is 4% probability that it will not be rejected. If a component is not defective there is 7% probability that it will be rejected. a) What fraction of all the components are rejected? b) What fraction of the components rejected are actually not defective? c) What fraction of those not rejected are defective? 11:58 AM

1. A company produces machine components which pass through an automatic testing machine. 5% of the components entering the testing machine are defective. However, the machine is not entirely reliable. If a component is defective there is 4% probability that it will not be rejected. If a component is not defective there is 7% probability that it will be rejected. a) What fraction of all the components are rejected? b) What fraction of the components rejected are actually not defective? c) What fraction of those not rejected are defective? 11:58 AM

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.7MCQ: Consider Figure 3.5. Match the following, those on the left to those on the right. (i) Im (a)...

See similar textbooks

Similar questions

Explain the operation of a full subtractor with necessary diagrams. What is the differencebetween half and full subtractor?
2. A bank of nickel-cadmium cells is used as the emergency lighting supply for a hospital. There are 100 cells connected in series and each has an A-hr rating of 120 A-hr. The bank has to be replaced, and the manufacturer is no longer supplying nickel-cadmium cells. It is decided to replace the cells with lead-acid cells. How many lead-acid cells will be required if each has an A-hr rating of 60 A-hr, and how should they be connected?
An AC ammeter is connected in series with the primary winding of T1. What is the expected current reading? An AC ammeter is connected in series with the secondary winding of T1. What is the expected current reading? An AC ammeter is connected in series with R1. What is the expected current reading? NOTE: Idc for HW rectifier = 0.318 * Ipeak = 0.45 * Irms Describe/Explain briefly the purpose/use of the array (series-parallel) connection of the rectifier diodes in the given circuit.
multirange ammeter was designed using direct method to give three scales with Rsh1= 0.001285989 0, Rsh2=0.000562552 0, and Rsh3=0.000100001 Q. The d'Arsonval meter has Rm=6 Q and full scale current of 1.5 mA. Find the ranges.? 8 (Ctrl) -
For Fixed Bias Configuration Solve for Ib, Ic and le. Atleast 2 decimal place. Be mindful of units. Assume Ic is not equal to le. ... 4 RC 15002 RB VCC 20V 90A/A 100k2 Ib=Blank 1 HA Ic=Blank 2mA le=Blank 3 mA Blank 1 Add your answer Blank 2 Add your answer Blank 3 Add your answer
Q2/A- what are the main cases of insulator failures? B-what are type testing of insulator?
19. Identify the response time of a meter. a. Time taken by output to reach final constant value from Zero value b. Time taken by output to reach 95% of value from 10% c. Time taken to settle inside 2% of the final value d. None of the options
1- spark gaps testing method is applicable for testing 2- the electrical circuit that we use to measure high voltages and is not affected by frequency change 3- We can say high voltages if exceed ------------ V (Alternating voltages) 4- Transient voltages which are caused over voltages be in two forms 5- High voltages can be generated for testing in three ways ------
These Insulators are used when equal Voltage is required across each Insulator unit. O A. RADING INSULATORS O B. GRADING INSULATORS O C. STRAINING INSULATORS O D. GAINING INSULATORS
In an energy meter, creep speed is the speed of the aluminium disc's at O a. Full load condition O b. Over load condition O c. Half load condition O d. None of the above
Need help with finding paramters
fast solutions