Consider the following plane stress state:Ox=30 MPa, y= -60 MPa, Txy= 30 MPa cwCalculate the following:1. The coordinates of the center of the Mohr's circle CThe location of the center of the Mohr's circle Cis (2. Principal normal stresses (01, 02)The principal normal stresses are σ₁ = 39.083. Maximum shear stress (7)The maximum shear stress is 54.08MPa.4. The angle from the x axis to 0₁ (p)The angle from the x axis to 0₁ (p) is -16.855. The angle from the x axis to 7 (s)The angle from the x axis to T (s) is 28.156. The radius of the Mohr's circleThe radius of the Mohr's circle is 54.08. ✰ MPa.MPa and 02 = -69.08 MPa.O-15 MPa,CWCCWO MPa).

Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

1. The coordinates of the center of the Mohr's circle C The location of the center of the Mohr's circle Cis ( -15 MPa, 2. Principal normal stresses (01, 02) The principal normal stresses are 0₁ = 39.08 3. Maximum shear stress (T) MPa and 02 = -69.08 O MPa). MPa.

1. The coordinates of the center of the Mohr's circle C The location of the center of the Mohr's circle Cis ( -15 MPa, 2. Principal normal stresses (01, 02) The principal normal stresses are 0₁ = 39.08 3. Maximum shear stress (T) MPa and 02 = -69.08 O MPa). MPa.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.4.21P: -18 through 7.4-25 An clement in plane stress is subjected to stresses a,, ay., and axy. (see...

See similar textbooks

Related questions

Q: a. 20 cm C. 100 cm 35 cm Pressurized A air solid cone B C Oil (SG = 0.8) 5 cm 30 cm open 50 cm 30 cm…

A: Given data, Density of oil, ρo=800 kg/m3 Density of mercury, ρHg=13600 kg/m3 To determine:- a)…

Q: Consider calculating the amount of natural gas required to heat water in a heater. A family in…

Q: What Will Happen If You Put Peeps in a Vacuum Chamber? - Easter Special. How is explaining why the…

Q: Hot combustion gases, modeled as air behaving as an ideal gas, enter a turbine at 145 lbf/in.2,…

Q: Determine the force it must exert on the 0.7-kg smooth cylinder. Express your answer to three…

Q: 3. A closed rigid container has a volume of 1 m³ and holds air at 344.8 kpa and 273 K. Heat is added…

Q: How long will it take to saw a rectangular piece of aluminum plate 8 inches wide and 1.5 inch thick…

A: Given : Width, w = 8 in Thickness, t = 1.5 in Length of cut, l = 8 in Cutting speed, v = 120 rev/min…

Q: Summary of how mathematics is used in Engineering.

A: Mathematics are very useful in the Engineering **As per company policy we are no supposed to…

Q: The magnitude of the force F is 680 lb. Determine the moment about point O, then the scalar…

Q: Replace the distributed loading with an equivalent resultant force, and specify its location on the…

A: Given:

Q: time Q2: The particle P starts from rest at point A at t and changes its speed thereafter at a…

A: (1) Write the given data. vA=0at,AB=2g

Q: Determine the reactions at the support And C of the following beam. Note that there is an internal…

A: Given that: The beam is subjected to a varying load. The point C is an internal hinge. It is…

Q: Consider a pumping system used in a cooling water loop. Water is drawn from a tank, which maintains…

Q: A grinding wheel rotates 1750 rpm and has a surface speed of 2290 ft/min. Find the diameter of the…

Q: The truck and the tanker have weights of 8000 lb and 20000 lb, respectively. Their respective…

A: Given that: Weight of the truck is 8000 lb and it is acting at G1. Weight of the tanker is 20000 lb…

Q: Find the support reactions for the simple beam below Y X A गगो 10 ft. B गीत 5 ft. 10

Q: The particle P starts from rest at point A and changes its speed thereafter at a constant rate…

Q: What rating is used for hearing protection devices? Noise reduction rating O Canister Color Code…

A: Hearing protection devices are used to protect the ears from the noises generated due to the working…

Q: e Materials Science and Materials Engineering. Enumerate 5 examples of Ceramics. Enumerate 5…

A: Materials engineers typically work in the manufacturing industry and may be engaged in the…

Q: Develop expressions for (a) the material acceleration, (b) shear strain rate, and (c) vorticity…

A: Introduction In this given problem for the calculation of material acceleration first, we will…

Q: Sketch a isometric drawing for each of the three sets of orthographic drawings

A: Given: A set of orthographic projections.

Q: 2. Recall the example problem we looked at in class (lecture 8) of a hanger on a wall supporting a…

A: For solution refer below images.

Q: 1. Find the internal resultant loadings at point C. Neglect the weight of the bar. Note: Point C is…

A: Find the internal loadings at point C.

Q: A 10 inch long silver wire is stretched to a total length of 11.50 inches. Find the value of strain

A: Given : original length of silver wire, L = 10 in final length of silver wire, l = 11.50 in To find…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

Q: Explic how a Mohr circle problem is solved

A: Mohr circle is a graphical method to solve complicated analyses. Plane stress transformation…

Q: Given the front and top view create the missing side view.

A: The side view is

Q: 2.2-3 A steel wire and a copper wire have equal lengths and support equal loads P (see figure). The…

Q: = Car A is traveling on the circular road at the constant speed of VA 60 km/h. At the instant shown,…

A: Given data: vA = 60 km/h = (60×1000)/3600 = 16.6667 m/s vB = 80 km/h = (80×1000)/3600 = 22.2222 m/s…

Q: Context At your summer job, your supervisor wants to test your physics skills. A new winch (a cable…

A: GivenConstraints The inclined ramp is made up of small cylinders that are free to rotate: there is…

Q: The free vibrations of a system are governed by the differential equation shown in the image, with…

A: The given information in the problem is listed in the following attached image:

Q: ● Pulley A has an angular acceleration given by a = 0.60 (rad/s?), where is measured in radians. If…

A: Write the given data with suitable variables. αA=0.6 rad/s2ωA1=2.9 rad/sh=0.7 mrA=50 mmrC=150…

Q: Hi, I am needing help with a formula to calculate fabric cost. Sample: 1. Fabric used per piece,…

Q: For the vector function (1)=(Ar, ln(cos(Ar))), calculate the curvature function (1), the unit normal…

A: Given: rt=AtlncosAt To find: Curvature function Unit normal vector Components of acceleration

Q: As shown in the figure, Refrigerant 22 enters the compressor of an air conditioning unit operating…

A: Given data: T1=40°FP1=80 lb/in2T2=160°FP2=200 lb/in2T3=90°FP3=200 lb/in2Tai=70°F=529.67 RPair=14.7…

Q: Replace the loading by an equivalent resultant force and couple moment acting at point O. (Eigure 1)…

A: Given data w = 8x2 (lb/ft) Find the equivalent resultant force Location of resultant force and…

Q: HOMEWORK 5 Question 2 A 1.5-m³ tank holds a two-phase liquid-vapor mixture of carbon dioxide at…

A: Given data Tank volume = 1.5 m^3 Temperature = -17°C vf = 0.9827×10-3 m^3/kg vg = 1.756 × 10-2…

Q: Three solid shafts, each of -in. diameter, are connected by the gears shown. Know that G= 11.2 x 106…

A: Given data: d=34inG=11.2×106 psiTA=100 lb.inTE=260 lb.in Need to determine the angle rotates in…

Q: Determine the reactions at the support And C of the following beam. Note that there is an internal…

A: Given Data- Beam given with uniformly varying load we have to find reaction at A and C

Q: A mechanic is reinstalling a newly-sharpened blade on a lawn mower. A wedged-in block of wood at C…

A: GivenF=34 lb

Q: Thermodynamics Question: Can you please reduce the first law energy balance for: Ideal gas is…

A: First law of energy Apply the following conditions to first law of energy i) isothermal compression…

Q: The bottom of a 5-lb vertical plunger is in the dashed position in resting equilibrium against the…

A: Given data as per the question Mass of button A =5 lb stiffness of spring =10 lbin=120 lbft Plunger…

Q: calculate de accelerations WA = 45 N WB = 180 N WC = 150 N μB s = 0.4 μB k = 0.30 μc = 0.35

Q: A small winch is used to raise a load W=124 lb. Find the magnitude of force P that should be appli…

A: Given, W= 124 lb

Q: 12. A COUPLE CONSISTS OF TWO VERTICAL FORCES OF 70 LB EACH WHICH IS FOUND ON FIGURE 11. ONE FORCE…

Q: It is only required to move the cutting tool from the circumference to the center of the workpiece…

A: Introduction A milling machine is a machine that removes material from a workpiece by feeding it…

Q: The uniform rod weighs 420LBa an has its center of gravity at G. Determine the tension in the cable…

A: Givenw=420LBa

Q: Pick up 2 types of pneumatic control components given in the lesson. Explain the specific…

A: Since you have been posted multiple questions. So, we are solving only first question for you. If…

Q: For problem on the picture. assume that the left side of the spring has a fixed end and the other…

Q: The collar A, having a mass of 0.75 kg is attached to a spring having a stiffness of k = 260 N/m.…

A: Given data Mass of collar = 0.75 kg Spring constant = 260 N/m Find the speed of collar and normal…

Question

Consider the following plane stress state:
Ox=30 MPa, y= -60 MPa, Txy= 30 MPa cw
Calculate the following:
1. The coordinates of the center of the Mohr's circle C
The location of the center of the Mohr's circle Cis (
2. Principal normal stresses (01, 02)
The principal normal stresses are σ₁ = 39.08
3. Maximum shear stress (7)
The maximum shear stress is 54.08
MPa.
4. The angle from the x axis to 0₁ (p)
The angle from the x axis to 0₁ (p) is -16.85
5. The angle from the x axis to 7 (s)
The angle from the x axis to T (s) is 28.15
6. The radius of the Mohr's circle
The radius of the Mohr's circle is 54.08. ✰ MPa.
MPa and 02 = -69.08 MPa.
O
-15 MPa,
CW
CCW
O MPa).

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An element in plane stress on the fuselage of an airplane (figure part a) is subjected to compressive stresses with a magnitude of 42 MPa in the horizontal direction and tensile stresses with a magnitude of 9.5 MPa in the vertical direction (sec figure part b). Also, shear stresses with a magnitude of 15.5 MPa act in the directions shown. Determine the stresses acting on an element oriented at a clockwise angle of 40g from the horizontal. Show these stresses on a sketch of an element oriented at this angle.
An clement m plane stress from the frame of a racing car is oriented at a known angle 8 (sec figure). On this inclined clement, the normal and shear stresses have the magnitudes and directions shown in the figure. Determine the normal and shear stresses acting on an clement whose sides are parallel to the \y axes, that is, determine crv, tr(_, and t, Show the results on a sketch of an clement oriented at B .
-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
.4-2 An element in uniaxial stress is subjected to tensile stresses sx= 57 MPa. as shown in the figure. Using Mohr’s circle, determine the following. (a) The stresses acting on an clement oriented at an angle 0 = 33° from the x axis (minus means clockwise). (b) The maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
A thin square plate in biaxial stress is subjected to stresses ?? and ??., as shown in part a of the figure. The width of the plate is h = 12.0 in. Measurements show that the normal strains in the x and v directions are s = 427 × 10-6 and s = 113 × l0-6, respectively. With reference to part b of the figure. which shows a Iwo-dimensional view of the plate. determine the following quantities. (a) The increase .d in the length of diagonal Oil. (b) The change . in the angle between diagonal Oti and the x axis, (c) The shear strain y associated with diagonals Oil and cf(that is. find the decrease in angle ced).
-18 through 7.4-25 An clement in plane stress is subjected to stresses a,, ay., and axy. (see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
Repeat the preceding problem using sx= 5.5 MPa. ??y= 4 MPa. and txy= 3.2 MPa.
-18 through 7.3-22 An element in plane stress (see figure) is subjected to stresses o, a., and (a) Determine the principal stresses and show them on a sketch of a properly oriented element. (b) Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element. 7.3-18 a=2I50kPa, ay=375kPa.Txy.=-460kPa
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clement
The polyethylene liner of a settling pond is subjected to stresses ax= 350 psi. a = 112 psi. and = -120 psi, as shown by the plalte-stress element in the figure part a. Determine the normal and shear stresses acting on a seam oriented at an angle 01300 to the element, as shown in the figure part b. Show these stresses on a sketch of an element having its sides parallel and perpendicular to the seam.