1.) The driving crank AB of a slotted lever quick return mechanism, as shown below, revolve at a uniform speed of 200 rpm. Find the following: A. Velocity of slider B B. Acceleration of the slider B along the slotted lever PQ C. Acceleration of slider R

1.) The driving crank AB of a slotted lever quick return mechanism, as shown below, revolve at a uniform speed of 200 rpm. Find the following: A. Velocity of slider B B. Acceleration of the slider B along the slotted lever PQ C. Acceleration of slider R

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the velocity of the slider D and the angular velocity of link CD for the engine mechanism shown in Fig. The crank 01A rotates at a uniform speed of 20 rad/sec in the clock wise direction. The various lengths of the given mechanism are. O1A =0.5 m, AB =1.0m, 02B =0.75m, BC =lm and CD =1.75m.
Crack AB of a slider crack mechanism shown in Figure 2 rotate at a constant speed of 300 rpm in clockwise direction. The connecting rod BC has a length of 1 m and incline at 45° to vertically positioned piston C. B 1m A 0.2 m 457 C Figure 2: Slider crank mechanism Draw the displacement diagram of the mechanism shown in Figure 2 to scale. Use a vector diagram to determine the velocity of the piston C and connecting rod BC. Calculate the acceleration of piston C and the angular acceleration of connecting rod BC.
Crank 2 (link 2) of the system illustrated in the figure below a constant speed of 60 rev/min ccw. Find the velocity and acceleration of point B and the angular velocity and acceleration of link 4 (link 4 is BO4). Link-2 is AO, and link-4 is BO4. Link-3 is sliding on link-4. = 120 mm, RA0, = 70 mm, RB0, = 280 mm. Ro,02 %3D W2 4 O2 15° 3
Velocity and acceleration analysis of four bar mechanism. The dimensions of the four bar mechanism of P1ABP2 as follows: P₁A-300 mm; AB-580mm; P₂B-360mm; and P1P2=600mm (fixed link). The angle AP1P2 120 degrees. The crank P,A has an angular velocity of 10 rad/s and angular acceleration of 30 rad/s²., both clockwise. Determine the angular velocities and angular acceleration of P₂B and AB and the velocity and acceleration of the joint B.
A flywheel rotates with a uniform speed of 108rpm for 5.3 seconds Then it is uniformly accelerated at 0.3rad/s for next 6.6 s. then it is made to stop in next 5s. Determine Omaximum angular velocity; (ii) total angular displacement 1.The angular displacement in rad 0, %3D 2.The angular displacement in rad 02 = 3.The maximum velocity in rad/s W;= 1. hp
Crack AB of a slider crack mechanism shown in Figure 2 rotates at a constant speed of 300 rpm in clockwise direction with the length of AB being 0,3 m. The connecting rod BC has a length of 1 m and incline at 45 degrees to vertically positioned piston C. 1.Draw the displacement diagram of the mechanism shown in Figure 2 to scale. 2.Use a vector diagram to determine the velocity of the piston C and connecting rod BC. 3.Calculate the acceleration of piston C and the angular acceleration of connecting rod BC.
The figure below depicts the linkages of a pump mechanism. If Q2A is rotating at 10 rpm in a clockwise direction, determine the linear velocity of slider D when Q2A has moved 60 degrees from its original position. Use R&C method. (Ks: 1 in. = 1 in.; Ky: 6 fpm = 1 in.) LINEAR VELOCITY OF B = EPM LINEAR VELOCITY OF C = FPM LINEAR VELOCITY OF D = FPM
(Use relative motion analysis): The planetary gear system is used in car transmissions. There is sun gear S, planet gears P and the ring gear R. By locking (fixing/grounding) certain gears you can have different gear ratios and car speeds. = c) If the output shaft is held fixed, i.e. WA 0, and the ring gear is rotated at WR 5 rad/s, find the angular velocity, wp of = the planet gears and ws the sun gear. ως d) What if the planet gears are held fixed, Wp = 0 ? Шр WR R P WS 80 mm 40 mm 40 mm A
Crack AB of a slider crack mechanism shown in Figure 2 rotate at a constant speed of 300 rpm in clockwise direction. The connecting rod BC has a length of 1 m and incline at 45° to vertically positioned piston C. B 1 m 0.2 m 45 Figure 2: Slider crank mechanism 3.1. Draw the displacement diagram of the mechanism shown in Figure 2 to scale. Use a vector diagram to determine the velocity of the piston C and connecting 3.2. rod BC. 3.3. Calculate the acceleration of piston C and the angular acceleration of connecting rod BC.
The lengths of various links of a mechanism, as shown in Figure 2, are: OA = 0.3 m; AB = 1 m; CD = 0.8 m; and AC = CB. A 45° B| Figure 2: Slider cranck mechanism 3.1. Draw the displacemt diagram to a scale. 3.2. Determine the velocity of piston B if the crank OA rotates at 160 r.p.m in the clockwise direction. 3.3. Calculate the velocity of point C.
rad The rod OA rotates clockwise at a constant angular velocity of 0 = (3) Two pin-connected slider block, located at B, move freely on OA. The curved rod is described by the equation r (300 (3-cos)) m. Hint: 1. Remember clockwise rotation is negative velocity. OA Variable 0₁ d₁ d₂ d3 0₁ d2 d3 Values for the figure are given in the following table. Note the figure may not be to scale. Value 110 degrees 0.45 m 0.1 m 0.275 m Using cylindrical components, a. Determine the cylinders's radial and transverse components of velocity at the instant shown, u, and vg. b. Determine the cylinders's radial and transverse components of acceleration at the instant shown, ar and ag. c. Determine the cylinder's magnitude of the velocity at the instant shown, ·M. d. Determine the cylinder's magnitude of the acceleration at the instant shown, |a1. Round your final answers to 3 significant digits/figures. 7= fr + a= M-C Hr+ m S M 82 He) Fe) m S m
1 of 1 3. A four-bar linkage is shown below. (A) the directions of each. (B) E on link 3. Use the method of velocity vector polygons to calculate w, and wq. Report Find and report the magnitude and direction of the absolute velocity of point RAD = 10 cm, Rap = 15 cm, Ra = 60 cm; R = 65 cm; Rp = 15 cm W2 = 2 rad/s cw (Note: ADB and FEC are right triangles.) link 3 A. link 2