1.30 Two wooden members of uniform rectangular cross section are joined by the simple glued scarf splice shown. Knowing that the maximum allowable shearing stress in the glued splice is 620 kPa, determine (a) the largest load P that can be safely applied, (b) the corresponding tensile stress in the splice.

1.30 Two wooden members of uniform rectangular cross section are joined by the simple glued scarf splice shown. Knowing that the maximum allowable shearing stress in the glued splice is 620 kPa, determine (a) the largest load P that can be safely applied, (b) the corresponding tensile stress in the splice.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The riveted lap connection shown consists of two(2) – PL 12 mm × 280 mm. 1. If allowable shearing stress in 20mm rivets is 186 MPa, find the maximum allowable force P that can be applied a. 233.734 kN b. 251.813 kN c. 283.406 kN d. 245.916 kN 2. If allowable bearing stress in holes is 1.2Fu where Fu is the ultimate strength of the plate and which is equal to 400 MPa, find the maximum allowable force P that can be applied neglecting effect of eccentricity. a. 563.3 kN b. 460.8 kN c. 683. 6 kN d. 405.9 kN 3. If allowable yielding of gross area is Fy/1.67, where Fy is the yield strength of the plate and which is equal to 250 MPa, find the maximum allowable force P that can be applied neglecting effect of eccentricity. a. 534 kN b. 560 kN c. 446 kN d. 503 kN 4. If diameter of hole equals diameter of rivet, what is the net area of edge-3-4-edge in square…
A pressure vessel of 225-mm inner diameter and 6-mm wall thickness is fabricated from a 1.2 m section of spirally welded pipe AB and is equipped with two rigid end plates. The gage pressure inside the vessel is 2 MPa, and 45-kN centric axial forces P and P' are applied to the end plates. P' A 1.2 m 35⁰ B Determine the shearing stress parallel to the weld. The shearing stress parallel to the weld is P MPa.
8. Two blocks are arranged as shown. At that position, if vx is 1 fpm, what is Vy, in fpm? C. 2.3 d. 2.9 a. b. 1.1 1.8 9. The lap joint shown supports a weight W equal to 200 lb. The bearing stress and the shear stress should not exceed 18 ksi and 9 ksi respectively. The thickness, t is 1/8 in. Determine the smallest diameter bolt, in inches, that can be used. a. 1/8 b. 5/32 W C. 3/16 d. 7/32 BOLT
Four plates, each being 15 mm thick, are to be connected by six bolts of 19 mm diameter as shown. Consider B = 181 mm. Assume that the force is equally distributed among the rivets. A. Determine the minimum force P (Newtons) if the allowable bolt shearing stress is 33 MPa. B. Determine the minimum force P (Newtons) if the allowable plate bearing stress is 32 MPa. C. Determine the tensile stress of the top plate (MPa) at segment a-a if the force P is 35 kN.
Re Several forces are applied to the pipe assembly shown. Knowing that Q= 250 lb and that the pipe has inner and outer diameters equal to 1.61 in. and 1.90 in., respectively, determine the normal and shearing stresses at point Hand point K. (Round the final answers to two decimal places.) 150 lb 10 in. 4 in. 150 lb 6 in. 50 lb 4.79 O ksi. The normal stress at point His The shearing stress at point H is 83.63 -41 ksi. ksi, The normal stress at point K is 3.83 O ksi. The shearing stress at point K is
For the riveted connection shown, the allowable shearing stress in the 25mm rivets is 140MPa. Assume the plates are adequate to transmit the load to the rivets. P = 60 kN.a. Determine the shearing stress in the most stressed rivet.b. Determine the maximum allowable value of P.c. If P = 80 kN, determine the minimum diameter of rivets.
A tensile stress of 75 Mpa and a shear stress of 35 Mpa are induced in a ductile material whose allowable strength in straight tension is 85 Mpa. Determine the maximum shear stress of the material? d.45.6 Mpa c.51.3 Mpa b.50.3 Mpa a.48.9 Mpa
Q.1. A. For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138, Determine the maximum tensile load that can be applied if the stress is limited to 115 MN/m2. B. What furce is required to punch a square hole (25-mm 25mm) in a plate that is 30 mm thick? The shear strength is 350 MN/m2. Puncher 25 mm *2 mm 30 mm Nck
Prob. # 2] The 1.5-in-diameter solid steel shaft shown below is simply supported at the ends. Two pulleys are keyed to the shaft where pulley B is of diameter 4.0 in and pulley C is of diameter 8.0 in. Considering bending and torsional stresses only, a) determine the locations and magnitudes of the greatest bending and torsional stresses in the shaft. Then, at the location of the maximum bending and torsional stresses, b) determine the maximum and minimum principal stresses, including the angle of inclination of the planes on which the principal stresses act, and c) the maximum shear stress, including the angle of inclination of the element on which the maximum shear stress occurs. Note: Draw the stress elements. Figure problem #2. 800 lbf 10 in 200 lbf 1000 lbf 10 in 200 lbf 10 in 1200 lbf 500 lbf 1600 lbf-in 10 in 100 lbf 10 in 1600 lbf-in 10 in 600 Ibf 400 lbf x 400 lbf
125 mm 75 mm 1,32 Two wooden members of uniform cross section are joined by the simple scarf splice shown. Knowing that the maximum allowable tensile stress in the glued splice is 500 kPa, determine (a) the largest load P that can be safely supported, (b) the corresponding shearing stress in the splice. 60" P' P1.32
HWs. 1. The grains of wood in the board make an angle of 20° with the horizontal as shown. Using Mohr's circle, determine the normal and shear stresses that act perpendicular and parallel to the grains if the board is subjected to an axial load of 250 N. -300 mm 60 mm 250 N 250 N+ 20 25 mm 2. The post has a square cross-sectional area. If it is fixed supported at its base and a horizontal force is applied at its end as shown, determine (a) the maximum in-plane shear stress developed at A and (b) the principal stresses at A. 18 in. 3. Determine the principal stress, the maximum in-plane shear stress, and average normal stress. Specify the orientation of the clement in cach case. 20 MPa 8O MPa 30 MP.
2. A hollow shaft of 30-mm inner diameter and 60-mm outer diameter is acted on by an axial tensile load of 50 kN, a torque of 500 N-m and a bending moment of 200 N-m. Determine the principal stresses and their directions.