PLEASE HELP ASAP Self Assessment 5600 mm1.37 Link BC is 6 mm thick, has a width w = 25 mm, and is made ofa steel with a 480-MPa ultimate strength in tension. What was the safety fac-tor used if the structure shown was designed to support a 16-kN load P?480 mm1.38 Link BC is 6 mm thick and is made of a steel with a 450-MPa ul-timate strength in tension. What should be its width w if the structure shownis being designed to support a 20-kN load P with a factor of safety of 3?

Answered: Image /qna-images/answer/22c55fcc-622c-47fe-a842-3093f01e6a04.jpg

1.37 Link BC is 6 mm thick, has a width w = 25 mm, and is made of steel with a 480-MPa ultimate strength in tension. What was the safety fac- r used if the structure shown was designed to support a 16-kN load P?

1.37 Link BC is 6 mm thick, has a width w = 25 mm, and is made of steel with a 480-MPa ultimate strength in tension. What was the safety fac- r used if the structure shown was designed to support a 16-kN load P?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: In tensile test the percentage of elongation was 29.8%. If the final length reached to 84.37mm, so t...

Q: Based on the figure identify only the relative polar coordinate of each point. The answer would be i...

A: In this problem, cartesian relative coordinates are given and we have to calculate the polar relativ...

Q: Q1. What is the level H if the flow rate through the system shown is 180 L/s through the 30-cm diame...

Q: 1,200 N-m 4,500 N-m 2,800 N-m 500 N-m (3) B 0.70 m 1.80 m 0.70 m Complete the torsion diagram of rod...

Q: Under conditions for which the same room temperature is maintained by a heating or cooling system, i...

Q: Determine the resuhant moment produced by the forces about point O. F, = S00N 125 m, 025 m

A: Given:F1=500 NF2=600 N

Q: The aluminum shaft, composed of three segments is fastened to rigid supports as A and D. Calculate t...

Q: Water in an enclosed volume of 1 m3 has heat added until it reaches a temperature of 150 Celsius. If...

Q: A 5.4 kg ball with a diameter of 11 cm is dropped form an airplane at an altitude of 9 km above the ...

A: Given data Mass of the ball = 5.4 kgDiameter = 11 cm = 0.11 mThe ball is dropped from an altitude of...

Q: Q3 Determine the required spring stiffness of kAB in Figure below so that the 10-kg lamp can be susp...

Q: 4 m F = {60i – 30j – 20k}N %3D 3 m X. -7 m- 4 m 6 m- 2 m

A: GIVEN DATA- A FORCE F GIVEN WE HAVE TO FIND MOMENT ABOUT POINT O

Q: A gasoline dealer commissioned a machine shop owner to fabricate a metal tank in the shape of a cyli...

A: given, Metal tank in the shape of cylinder of height H, with hemispherical bottom and circular cover...

Q: If the internal torque experienced by a solid brass shaft (G =39 GPa) with radius r=50 mm is T = 12 ...

A: Consider a twisting moment T is applied to a shaft having radius R. Then, torsional shear stress dev...

Q: Q6/ The 300lb body A and the 400lb body are connected by a cable passing over a smooth pully on the ...

Q: A 100 mm diameter bar is used as a simply supported beam 4m long. The value of :Moment of Inertia (1...

A: Given Data D=100 mm

Q: Two blocks of wood 50mm wide and 20mm thick are glued together. a. Using the free body diagram conce...

A: Given,

Q: 4. Determine the length of the rod and the position vector directed from A to B. What is the angle 0...

A: Given,

Q: 1.1. The pump whose performance curves are shown in Figure P1.1 is operated at 1750 rpm and is conne...

A: for problem 1.1 according to the given diagram: Q = 140 gpmH =50ftη = 50% flow rate = 140 gpm = 0.31...

Q: The rigid bar of negligible weight is supported as shown. The assembly is initially stress- free. Fi...

A: Answer: (a) The stress in the bronze bar is 50.78 MPa. (b) The stress in the steel bar is 52.11 MPa....

Q: %3D An LLE separating tank (r,c 36 cm) is filled with a combination of water (rho,w = 0.99 g/cm^3, h...

A: How much liquid passing a segment of a stream in unit time is known as the release. Assuming v is th...

Q: The 10-mm-thick bottom of a 200-mm-diameter pan may be made from aluminum (k = 240 W/m-K) or copper ...

Q: Determine the force magnitude F and direction (measured clockwise from the positive y-axis) that wil...

Q: A piece of 3 m long and having a 30 cm by 30 cm is placed in a body of water in a vertical position....

Q: 2016. Two cars A and B have a velocity of 60 mph in the same direction. As 250 ft behind B when the ...

A: GIVEN DATA- V=60mph=88 ft/s DISTANCE BETWEEN A AND B =250ft DEACCELERATION OF CAR B =10 ft/s2

Q: A solid circular bar of steel (G = 78 GPa)transmits a torque T = 360 N ? m. The allowablestresses in...

Q: 4. If the same engine (i.e., four-stroke, 2 liters) as above produces 76 kW at 5400 rpm (90 Hz), Fin...

Q: Which one of the following statements about hydrostatics is TRUE? Select one: Oa. the buoyancy force...

A: Concept:Buoyant force is the upward force exert by the fluid on the floating or submergedbody.Archim...

Q: In a hydrocarbon processing plant, Fluid A (cp = 4.31 kJ/kg K) entering the tube side is used to hea...

Q: Three coplanar forces are given as follows: A=6 N at 250°, B= 10 N at 120°, and C = 16 N at 205° Plo...

Q: Determine the volumetric displacement of a V6 four stroke engine with a bore and stroke of 86 x 86 m...

A: Given data V6 Engine - Six cylinder engineBore = 86 mmStroke = 86 mmRunning speed = 4200 rpm

Q: The concrete slab of a basement is 11 m long, 8 m wide, and 0.5 m thick. During the winter, temperat...

A: Given: slab of 11m X 8m X 0.5m K = 1.4 W/mK T1 = 17 deg C T2 = 10 deg C

Q: 141.4 lb 1' 361 lb 224 lb

Q: While evaluating the performance of a boiler it is observed from flue-gas analysis that %02 content ...

A: Given data as per question % O2 of flue gas before entry rotary heater =7%% O2 of flue gas leaving ...

Q: The uniform 14-m pole has a mass of 190 kg and is supported by its smooth ends against the vertical ...

Q: An irreversible Stirling cycle containing 5.0 mol of a diatomic ideal gas goes through the following...

A: a) P-V diagram of the processes is The P-V diagram of the complete Stirling cycle is 1) Process a-b...

Q: How would you compare the accuracy of the graphical (polygon) method and experimental (force table) ...

Q: O O O .. .is method used for testing the hardness of brittle materials such as ceramics. and polymer...

A: Rockwell hardness test is commonly used for testing hardness of brittle materials like ceramics and ...

Q: From the bending diagram, given the value of moment is 4000 Ib.ft. The value (C) from the neutral ax...

Q: The composite beam shown in the Figure below is formed of a wood beam and a steel reinforcing plate....

Q: Determine the moment about point A due to the three applied forces on the frame to the right. Answer...

Q: An object has path described by the equation y = (x³²)/4. If at the point P, x = 16 m, v = 28.8 m/s ...

Q: *:This type of moment caused 5 J Bending momet Shear Force Axial Force Torsion

Q: 4. A 250 hp motor turns a shaft at 2400 rpm. The shaft steps down in diameter from 3.0-in to 2.5-in ...

Q: For the overhanging beam with shown loading, sketch the shear and moment diagrams. 50 kN 50 kN 30 kN...

Q: What is the capacity of an engine in cc with four cylinder that has bore x stroke = 79 mm x 77 mm? S...

A: Given:Bore diameter, d=79 mmstroke length, l=77 mmnumber of cylinder, n=4

Q: A cylindrical vessel with 2 m diameter and 4 m length initially contains R-134a at 1 MPa, 100 degree...

Q: A Carnot heat engine receives heat from a reservoir at 1200°C at a rate of 800 kJ/min and rejects th...

Q: 4. Steam at 173.46 degree C and with a specific entropy of 6KJ/kg-K undergoes a polytropic process w...

A: From guidelines first question will be done from multiple questions. Post again for another question...

Q: The 10-mm-thick bottom of a 200-mm-diameter pan may be made from aluminum (k = 240 W/m-K) or copper ...

Q: In a insulated rigid container there is helium gas being stirred by a paddle wheel using 0.02 hp for...

Concept explainers

Forms of Energy

Energy is described as the capability to accomplish a task, like the ability to push a block by applying force on it. It is a quantitative property that is used to accomplish work on an object.

Question

100%

PLEASE HELP ASAP

Self Assessment 5
600 mm
1.37 Link BC is 6 mm thick, has a width w = 25 mm, and is made of
a steel with a 480-MPa ultimate strength in tension. What was the safety fac-
tor used if the structure shown was designed to support a 16-kN load P?
480 mm
1.38 Link BC is 6 mm thick and is made of a steel with a 450-MPa ul-
timate strength in tension. What should be its width w if the structure shown
is being designed to support a 20-kN load P with a factor of safety of 3?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

You are given a square rod of 6061-T6 aluminum (cross-section = 4mm X 4mm, length = 2.3m). The material has a Young’s modulus of 72 GPa. If a tensile load of 3 kN is applied parallel to the 2.3m dimension, what is the change in length of the rod?
A bar, 12 mm in diameter is acted upon by an axial load of 20 kN. The change in diameter is measured as 0.03 mm. DeterminePoisson’s ratioYoung’s modulusBulk modulus Assume modulus of rigidity as 80 GPa
A tensile force of 100 kN is applied on a 0.02-m diameter and 2-m long rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length increases to2.01 m. The true axialstrain is?
Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution Video. If load P = 23.5 kips, determine the normal force in bar (1). A 6 ft 49.9 kips 39.2 kips 41.5 kips 31.9 kips 23.7 kips D B (1) 4 ft P
If load P = 20.1 kips, determine the normal force in bar (1). D P A 6 ft 42.0 kips 28.2 kips 33.5 kips 45.4 kips 30.9 kips B (1) 4 ft
If load P = 20.1 kips, determine the normal force in bar (1). (1) A 6 ft 42.0 kips 28.2 kips 33.5 kips 45.4 kips 30.9 kips B 4 ft
The link shown, made of steel with y-410MPa and E-200GPa is subjected to a tensile load of 30kN. Let (h=6b). Assume the factor of safety is 2. a) Determine the dimensions of the section with the design based on yield strength. b) If this link, which is 40cm long, must not elongate more than 0.12mm, what should be the dimensions of the cross section? L F F -h b
Q1: A 75 mm diameter compound bar is constructed by shrinking a circular brass bush onto the outside of a 50 mm diameter solid steel rod. If the compound bar is then subjected to an axial compressive load of 160 kN, determine (a) the load carried by the steel rod and the brass bush; (b) the compressive stress set up in each material. The modulus of elasticity for steel, E. = 210 GN/m², and brass, E = 100 GN/m².
Let's considera rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E= 200 Gpa and a Poisson's ratio of 0.3. If a tensile force Fis subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F Select one: OF 5236 N O F=15708 N Clear mopshoe Finish attempt
See the set of bars for made of a material that has a yield strength of 350 MPa, determine the minimum h1 and h2 dimensions required. Apply a safety factor F.S. = 1.5 without flow. Each bar is 12 mm thick
TOPIC: ELASTICITY A load of 50 kg is applied to the lower end of a steel rod 80 cm long and 0.60 cm indiameter. How much will the rod stretch? Y = 190 GPa for steel. Please help me solve this problem with complete solution and box the final answer. Please also draw an illustration based from the given. Thank you!
A very fine fabric 0.020 mm in diameter can support a 20 g object. How does the stress in the fabric compare with the ultimate strength in tension of copper