11. In an RC series circuit EMF = 120.0 V, R = 1.40 MQ, and C = 1.80 µF. (a) %3D Calculate the time constant. (b) Find the maximum charge that will appear on the capacitor during charging. (c) How long does it take for the charge to build up to 20 uC? (d) What is the maximum current through the resistor? (e) What is the potential difference across the capacitor after it has been charging for 1.0 sec? (Đ Sketch the charge and current as functions of time. (g) After being totally charged, the capacitor is carefully disconnected from the circuit above without discharging it. It is connected to a 520 kQ resistor and begins to discharge. What is the time constant for this circuit? (h) What will be the potential difference across the capacitor after 400 msec? (i) Sketch the charge and current as functions of time.

11. In an RC series circuit EMF = 120.0 V, R = 1.40 MQ, and C = 1.80 µF. (a) %3D Calculate the time constant. (b) Find the maximum charge that will appear on the capacitor during charging. (c) How long does it take for the charge to build up to 20 uC? (d) What is the maximum current through the resistor? (e) What is the potential difference across the capacitor after it has been charging for 1.0 sec? (Đ Sketch the charge and current as functions of time. (g) After being totally charged, the capacitor is carefully disconnected from the circuit above without discharging it. It is connected to a 520 kQ resistor and begins to discharge. What is the time constant for this circuit? (h) What will be the potential difference across the capacitor after 400 msec? (i) Sketch the charge and current as functions of time.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter19: Capacitors

Section: Chapter Questions

Problem 2PA: You are an electrician working in an industrial plant. You discover that the problem with a certain...

See similar textbooks

Similar questions

You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
The voltage signal coming out of the capacitor is with small ripples compare to the voltage signal out of the diode. True False
What voltage is boosted at the output of a multiplier.Choices: average, rms, peak, or instantaneous Which assumption is not used in the analysis of multipliers?Choices: a capacitor will not discharge, start with the cycle of the source that will forward bias the nearest diode, the output will always be multiplied, or a single diode is forward biased at a time A voltage multiplierChoices: multiplies the output voltage, has very high voltage and low current ,can employ inductors, or may not have equal numbers of diodes and capacitors A voltage regulator maintains constant voltage at the load regardless of variations atChoices: the input and output, the load, source, or in the environment Between a lower percent regulation and a higher one, which is better?Choices: lower or higher
1. 1-5 K 30v a. what is tue T CTime constant) ? b. How long will it take for the capacutor TO rtach s0% op charge? C. What is tne voltage of capa citor apter 1 seconds? d. How many tíme constants will it take for the soltage to reach 23 v? C. Gweng that the capacitor is fully changed, how will it take por it to be 20% ? long 120v + BF what is the. T ? b. what is the voltage capacitor apter 10 sec? a. C. How many time constants will it take for Tue Vo Itage to reach 80 v.? d. Given that the capaator is Fully charged, how time constants will it be to reau many GOV!
1. Which of the following answers best describes discontinuous conduction mode? A. The inductor voltage ripple goes negative B. The inductor current ripple stays positive C. The inductor current ripple falls to zero D. The output current ripple falls to zero
A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Va.. (t) 10 kO 8V 10 kO Vin Vin(t) D2 Vout(t) RL Ims D1 6V -8V 4V Page | 1
Full-wave rectified sine wave circuit is used to measure the RMS value of a half square wave with the help of PMMC meter. The meter was actually calibrated for sine wave. The circuit uses a meter movement with a full scale deflection current of 200uA and internal meter resistance of 5kΩ. Assuming Non-ideal diodes having resistance 1kΩ, Analyze the circuit to determine the value of series multiplier resister and the corrected RMS voltage, if meter is to read 225V RMS full-scale.
c. If a 480 ?F capacitor is added to the output in the figure, calculate the following:i. Vripple.ii. Average voltage, Vdc.iii. Sketch a graph of the input and output voltage against time of the capacitor. (Built-in-potential of silicon = 0.7V)
The anode of a diode is connected to one terminal of a 1-KΩ resistor. The other terminal of the resistor is connected to the ground and the negative terminal of a 12-volt DC source is also grounded. The three components are connected in series. How much is the load current with the ideal diode?
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consistingseries connected a resistor and an inductance from a 70.7V (RMS), 50Hz sinusoidal AC source.The firing delay of the thyristor is 90° and the load values are R=10Ω, L=0.1 H. Define the loadcurrent expression and draw the load current by calculating for first two periods. And calculate theaverage values of the load voltage and current.
Example 5-2: A full-wave rectifier is operated from a 50 Hz line and has a filter capacitor connected across its output. What minimum value of capacitance is required if the load is 1.2 k2 and the ripple must be no greater than 2.4%? Solution: * 100% 2/3 f.R: C