"17-1 Find the torque that a 2-surface, dry disk clutch can transmit if the outside and inside lining diameters are 120 mm and 70 mm, respectively, and the applied axial force is 10 kN. Assume uniform wear and u = 0.4. Is the pressure on the lining acceptable? What lining material(s) would be suitable? %3D

"17-1 Find the torque that a 2-surface, dry disk clutch can transmit if the outside and inside lining diameters are 120 mm and 70 mm, respectively, and the applied axial force is 10 kN. Assume uniform wear and u = 0.4. Is the pressure on the lining acceptable? What lining material(s) would be suitable? %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4. A multiple disc clutch running in oil is required for a touring motorcycle. The power demand is 75 kW at 9000 rpm. Space limitations restrict the maximum outer diameter of the clutch plates to 200 mm. Select an appropriate lining material and determine the radii for the discs, the number of discs required and the clamping force. 5. A multiple disc clutch is required for a high-performance motorcycle. The power demand is 100 kW at 12 000 rpm. Select an appropriate lining material and determine the radii for the discs, the number of discs required and the clamping force. 6. A multiple disc clutch is required for a small motorcycle. The power demand is 9 kW at 8500 rpm. Select an appropriate lining material and determine the radii for the discs, the number of discs required and the clamping force. 0. oolinor b
A A multiple disc clutch transmits 55 kW of power at 1800 r.p.m. The coefficient of friction is 0.1 and the axial intensity of pressure is not to exceed 160 kN/m. The internal radius is 80 mm and is 0.7 times the external radius. Find the number of plates needed to transmit the required torque.
Q1/ A plate clutch having a single driving plate with contact surfaces on each side is required to transmit 110 kW at 1250 r.p.m. The outer diameter of the contact surfaces is to be 300 mm. The coefficient of friction is 0.4. (a) Assuming a uniform pressure of 0.17 N/mm? ; determine the inner diameter of the friction surfaces. (b) Assuming the same dimensions and the same total axial thrust, determine the maximum torque that can be transmitted and the maximum intensity of pressure when uniform wear conditions have been reach.
Determine the resulting torque of a uniform pressure frictional clutch having 4 discs in the driving part and 5 ones in the driven part>The angular speed is 100 rad/sec and the applied load is 2 KN. The outer and inner radii of the frictional faces are 300 and 450 mms respectively with a coefficient of friction of 0.3. How much power will be developed? e 12:26 Single lap riveted joint of a thickness of (2 cm); the diam of rivet is (16 mm). Find the efficiency of a rivet joint of a pitch of (4 cm). If the stresses of the joint are as follows: shear stresses=1200 N/mm^2, bearing stress= 1000 N/mm^2, Tearing stress 1200 N/mm^2 P 12:31 II
A multiplate disc clutch transmits 55 kilowatt of power at 1800 rpm. Coefficient of friction for the friction surface is 0.1. Axial intensity of pressure is not to exceed 160 KN/m2. The internal radius is 80mm and is 0.7 times external radius. Find the number of plates needed to transmit the required torque.
*17-5 How many surfaces are needed in a wet disk clutch to transmit 120 N-m of torque at 1 000 rpm using a sintered lining with a maximum pressure of 1.8 MPa and u = 0.06? Assume uniform wear. Find the outside and inside diameters required if r; = 0.577r. How many disks are needed? What is the power transmitted?
Q3 / A multi – plate clutch is to transmit 12 kW at 1500 r.p.m. The inner and outer radii for the plates are to be 50 mm and 100 mm respectively. The maximum axial spring forces is restricted to 1 kN. Answer the following questions 1- The necessary number of pairs of surfaces is µ= 0.35 assuming constant wear. 2- The necessary number of pairs of surfaces is constant pressure. µ= 0.18 assuming 3- The axial force 4- Percentage increase in forces is
A cone clutch has an angle of 12 dgrees and coefficient of friction of 0.42. Find the axial forcerequired if the capacity of the clutch is 8 KW at 500 rpm. The mean diameter of the active conicalsections is 300 mm. Use uniform wear method.
A multiple disk clutch consisting of 3 disks on the driving shaft and 2 disks on the driven shaft is to transmit 67.5 kW at a speed of 1500 rpm allowing for 25% overload. Assume uniform wear where the average allowable pressure is 0.20 N/mm² and the coefficient of friction for the surfaces is taken as 0.15. The outside diameter of the surfaces is to be 1.5 times the inside diameter. The axial thrust is to be provided by 9 springs with 4 active turns and is of spring index = 6. For spring material, the safe shear stress is to be limited to 420 MPa and the modulus of rigidity may be taken as 80 kN/mm². a) Determine the Outside and inside radii of the discs. b) Determine the Axial force on the clutch c) Determine the Spring dimensions d) Determine the shaft diameter if the shear stress for the shaft material is 50 N/mm².
A local utility vehicle production company have considered using in one of its design a multi-disc clutch consisting of a 9 steel disc and 8-bronze discs with effective outside and inside diameter of 220mm and 160mm, respectively. If the shaft turns at 150rpm and an axial force of 600N is applied, find the horsepower capacity, considering a coefficient of friction of 0.25
*17-3 Design a single-surface disk clutch to transmit 100 N-m of torque at 750 rpm using a molded lining with a maximum pressure of 1 MPa and u = 0.25. Assume uniform wear. Find the outside and inside diameters required if r; = 0.577rp. What is the power transmitted?
A multiplate disc clutch transmits 75 kW of power at 2000 rpm. Coefficient of friction for the friction surfaces is 0.2. Axial intensity of pressure is not to exceed 180 kN/m?. Internal radius is 100 mm and is 0.8 times the external radius. Find the number of plates needed to transmít the required torque. Assume uniform wear conditions.