/Consider the four- input NOR logic gate in figure below, The transistor parameters are VTNL =-IV, and VTND = 0.5V. The maximum value of Vo in its low state is to be 0.2 v. Determine :- a) Ko/KL b) The maximum power dissipation in the NOR logic gate is to be o.1 mw. find c) Vo when VA = VB = Vc = Vo = 3 V. 10 MA VB to the MB 3v VTNL = -1V KL Me VT Vo MD VTND 30.5V KD

/Consider the four- input NOR logic gate in figure below, The transistor parameters are VTNL =-IV, and VTND = 0.5V. The maximum value of Vo in its low state is to be 0.2 v. Determine :- a) Ko/KL b) The maximum power dissipation in the NOR logic gate is to be o.1 mw. find c) Vo when VA = VB = Vc = Vo = 3 V. 10 MA VB to the MB 3v VTNL = -1V KL Me VT Vo MD VTND 30.5V KD

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2) Derive the NOT gate and then sketch the MUX equivalen?
A certain digital circuits designed to operate with voltage levels of -0.2Vdc and -3.0Vdc. If H= 1 =-0.2 Vdc and L =0 =-3.0 Vdc, is this positive logic or negative logic ? H=+5.0Vdc. and. L=+1.0Vdc What are the voltage levels between fall and rise times are measured? What is the value of Duty cycle H if the waveform is high for 2 ms and low for 5 ms?
1- The thyristor holding current is defined as :* the minimum thyristor current that holds the thyristor in conducting state before switching off. the minimum gate current that holds the thyristor in conducting state before switching off. the minimum thyristor current that holds the thyristor in conducting state after removing the gate signal. 2- By increasing the gate current we obtained further :* increase in the break over thyristor voltage decrease in the break over voltage and reduction in the firing angle decrease in the break down voltage and reduction in the conducting angle . 3- In dc circuits decreasing the gate voltage causes :* increase in the breakdown voltage decrease in the delay angle decrease in the thyristor anode current Nor of them
In Fixed-bias configuration, the DC voltage across the Gate terminal is equal to ____. a.Vp b.Vgs c.Vds d.0V
VDD = 16V, RG = 1M-ohm, RD = 1500 ohm, RS = 750 ohm, IDSS = 10mA, VP=-4V a. Determine the drain current ID in mA. b. Determine the gate voltage, VG c. Determine the source terminal voltage, VS d. Calculate the drain terminal voltage, VD e. Determine the drain-to-source voltage, VDS
Rewire these two logic gate diagrams as circuits with IC (integrated circuit) Chips.
The gate of a JFET is . . biased Select one: a. forward b. reverse as well as forward c. none of the above d. reverse
Draw the circuit diagram of 4-bit Ripple Carry Adder. Page 6 of 8
Q5) Find the truth table for the two inputs-one output gate based on (RTL) family as shown in Figure (1). Using BC107 NPN transistor and BC109 PNP transistor that have saturation collector current Icat = 80mA, VCE 0.2 volt, B = 150, VBE Sat = 0.8 volt and Vcc=5 volt. sat %3D +Vcc R1 Output A R2 R2 Vcc = 5v R1:5 k2 R2: 10 k2 Figure (1)
Compare the behavior of the 7408 2-input AND gate with that of the 7400 2-inputNAND gate. In what way do they behave similarly? In what way are they different?
4.2.1. Three-Input AND Gate Show the schematic of a LUT (using a multiplexer0 which implements the logic for a 3-input AND gate.
Q6) Find the truth table for the two inputs-one output gate based on (RTL) family as shown in Figure (1). Using BC109 PNP transistor that has saturation collector current Icsat = 80mA, VCE sat = 0.2 volt, B = 150, VBE sat = 0.8 volt and Vee=5 volt. +Vcc R1 Output A R2 R2 Vcc = 5v R1:5 kn R2: 10 ka Figure (1)