*2-20. The piece of plastic is originally rectangular. Determine the average normal strain that occurs along the diagonals AC and DB. Geometry: AC = DB = √400² + 300² = 500 mm ᎠᏴ . -√405² +304² = 506.4 mm A'C' V401²+ 300² 500.8 mm - 2 mm 300 mm 2 mm D 400 mm- A mm, B 3 mm 14 mm 12 mm -X

*2-20. The piece of plastic is originally rectangular. Determine the average normal strain that occurs along the diagonals AC and DB. Geometry: AC = DB = √400² + 300² = 500 mm ᎠᏴ . -√405² +304² = 506.4 mm A'C' V401²+ 300² 500.8 mm - 2 mm 300 mm 2 mm D 400 mm- A mm, B 3 mm 14 mm 12 mm -X

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. The bar shown has a diameter of 2 in. and is made of an elastic-perfectly material with the stress-strain behavior as shown. If a force of P= 110 kip is applied to the bar, determine the stress in the segments AC and AB. o (ksi) P 20 |C B -2 ft - 3 ft e (in./in.) 0,001
*9-8. Determine the equivalent state of stress on an element at the same point oriented 30' clockwise with respect to the element shown. Sketch the results on the element. 9-9. Determine the equivalent state of stress on an element at the same point oriented 30 counterclockwise with respect to the element shown. Sketch the results on the element. |75 MPa 100 MPa Probs. 9-89
Q2) A rectangular block of an elastic material is subjected to normal and shear loads. The deformed (distorted) shape of the block is shown by the dashed lines. Determine the shear strain Yxy at corners D and C. Also find the average normal strain that occurs along the diagonal's AC and DB. 4 mm 2 mm 4 mm 2 mm; 300 mm }2 mm D 500 mm- A 3 mm
allowa quired wall thickness 2:11 .l 0.31 KB/S 64 Edit 16 A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as shown. Neglect deflections of the bar due to bending. Use E = 200 GPa. 36 mma 2 m OWhat is the displacement of the loaded end B of the bar? ® Determine the tensile stress induced in rod CD by the 80 kN load D If the allowable stress in rod CD is 124 MPa, what weight W can be safely 1.8 m 12m applied? w80 AN 1. A holl ow cir cular steel colum n is s ubjected toa compression load of 380 kN . The column has a length of 2.4 mn.and an outside dia meter of 187.5 mm. E - 200,000 MPa Determine the min. roquired wall thicknesss base on an allo wable com pressi ve stress of 48 MPa. Determine the min. required wall thickness based on 30 MPa. Determine the min. required wall thickness based on the allowable shortening of the colum n to b e 0.5 0 mm- allowable shear stress of C3D P-38 O kN 2.4 m 2. An 8 mm diameter steel rod, 20 m. long…
19. Power is force divided by time.( True False 20. The bolts in the coupling connecting two rods are stressed while the rods are rotating. The stress is shear. True False 21. Ultimate strength is the highest ordinate in the stress-strain diagram. True False
200mm Strain gauge F mun +100m 200mm- 4mm Strain gauge 4mm 12mm 12mm 4mm A small T-section is used in inverted positions as a beam and is shown in figure over a span of 400 mm. If due to the application of forces shown, the longitudinal strain gauge at F registers a compressive strain of 1500 microstraints, determine the magnitude of P. Take E = 200 GPa.
Three steel rods, each having a cross-sectional area of 500 mm2, are assembled in a symmetrical manner, ass shown in the igure. Assume that steek behaves as a linear elastic material with E= 200 GPa. Determine the deflection of joint A due to a downward force of P= 2MN
Beam AB is made of three plates glued together and is subjected, in its plane of symmetry, to the loading shown. Knowing that the shear force is V=3.5kN and I=8.63*106 m“, determine the following: -100 mm 20 mm -Joint a 80 mm C 20 mm - 68.3 mm 20 mm 60 mm The value of Q is equal to in m3: The value of t for the Joint a is equal to in mm: The average shearing stress at Joint a is equal to in kPa:
= 13.3 × 10- At a temperature of 32°F, a 0.09 in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [a 6/°F] and bar (2) is stainless steel [a 7.7 x 10-6/°F]. The supports at A and C are rigid. Determine the lowest temperature at which the two bars contact each other. Assume L₁ = 32 in., L₂ = 65 in. = (1) (2) B A L₁ g Answer: Final temperature = i bo L2 °F.
Compute the deformation of the beam using conjugate method E= 200 GPa I= 1000 x 106 mm4
The two bars are made of polystyrene, which has the stress-strain diagram shown. If the cross-sectional area of bar AB is 975 mm² and BC is 2600 mm², determine the largest force P that can be supported before any member ruptures. Assume that buckling does not occur. Include complete steps with explanations and FBD. 1m baxilno σ (MPa) 175 140 105 70 A 35ptension 0 0.20 -1.2 m P 0.40 compression B 0.60 0.80 € (mm/mm)
8 4. Complete the following a. Draw Mohr's circle for the element given and label the axes b. Determine 01, 03, and Tmax for the element -4 c. Determine the stresses (on, Tn) on the plane shown d. Plot the point representing the plane with stresses (On, Tn) on the circle Tn 5 40 5 8