Please answer d, e and f only, thanks 2. A built-up W-section is to be used as a girder. It is simply supported over aspan of 12 meters. It has a lateral support 5 meters from the left support.Use Fy=415 MPa and Cb=1.0Properties of the section:A=16,288 mm²br=300 mmtr=16 mmd=450 mmtw=16 mmIx=549,638.71x10³ mm4 -72,142.68x10³ mm³IFSU-LAG-INS-F012Rev.00(Jan.03,2022)a. Determine the elastic section modulus, Sx.b. Determine the plastic section modulus, Zx.c. Determine the compactness of the section.d. Determine the lateral support condition.e. Determine the Allowable Flexural Strength of the girder in N-mm.f. Determine the Ultimate Flexural Strength of the girder in N-mm.Express your final answers in 2 decimal places.

Area, width of flange, depth of section, thickness of flange, NOTE According to company guidelines,…

2. A built-up W-section is to be used as a girder. It is simply supported over a span of 12 meters. It has a lateral support 5 meters from the left support. Use Fy=415 MPa and Cb=1.0 Properties of the section: A=16,288 mm² d=450 mm tw=16 mm Ix=549,638.71x10³ br=300 mm t₁=16 mm mm -72,142.68x10³ mm³

2. A built-up W-section is to be used as a girder. It is simply supported over a span of 12 meters. It has a lateral support 5 meters from the left support. Use Fy=415 MPa and Cb=1.0 Properties of the section: A=16,288 mm² d=450 mm tw=16 mm Ix=549,638.71x10³ br=300 mm t₁=16 mm mm -72,142.68x10³ mm³

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A built-upsection is to be used as a girder. It is simply supported over a span of 9 meters and laterally supported at supports and midspan. Use Fy=345MPa and Cb=1.0 Properties of the section: A=12,620mm2 d=450 mm tw=10 mm bf=300mm tf=14mm rx=203.88mm ry=70.67 mm Ix=524.59x106mm4 a.Determine the elastic section modulus, Sx. b.Determine the plastic section modulus, Zx. c.Determine the compactness of the section. d.Determine the lateral support condition. e.Determine the Allowable Flexural Strength of the girder. f.Determine the Ultimate Flexural Strength of the girder.
Find the Beam Design Moment Strength. 250 So - 19.5 30 -75- 20 100 100 50 50 46 -40 31.15.7 29.8 180 3 Seven wire strand A = 99mm² x 3 f'c = 55M²₂² ty = 400MPa 2 201 Steel d=18.5mm A=300mm² for each 500mm Ecu=0.003
Compression member AB is used to hold up the 355 x 560-mm rectangular plate. If the compressive force in the member is 250 N for the position shown, determine the magnitude of the projection of this force (as it acts at point A) along diagonal OC. 355 136% 395 400 160 Answer: Foc= i 108 C B Dimensions in millimeters 145 N
5. Calculate the design flexural strength of the T-beam shown. Use f'c = 27 MPa and fy = 350 MPa. br= 600 mm 25 mm t= 110 mm 3-22 mm 10 mm stirrup hw= 390 mm 10-25 mm 25 mm 20 mm bw 300 mm
The steel truss (E =200 GPa) shown in figure below has a cross-sectional area of 1920 mm². Determine: a. The largest allowable load F if the change in length of member BD is not to exceed 1.6 mm and a factor of safety of 2.5. b. The displacement of support D due to the load calculated in part a. 5m 6m A C F
8m A 6M using in F B с 100KN 8m 6m Method of Sections determine forces FE, FC, BC
/. u/ es ug up w21E A W21 x 50 spans 11.0 m on a simple span. The compression flange is laterally supported at the third points. A36 Steel is used. A = 9,484 mm² b₁ = 165.9 mm Properties of W21 x 50 section tw = 9.7 mm Ix=409.57 x 10 mm Iy = 10.36 x 10 mm Sx = 1548.58 x 10³ mm³ Sy = 125.20 x 10³ mm³ d=529.1 mm tf = 13.6 mm w = 0.73 kN/m a) Determine the allowable bending stress of this beam. b) Determine the allowable superimposed uniformly distributed load be place on this beam.
Determine the design strength of the beam shown. Assume fy=345MPA and fc'=21MPa. 3-22 mm 75 375 mm 375 450 mm
Virtual Work for Beams and Frames #2 Determine the slope and the displacement at the end C of the beam. E = 200 GPa, I = 70(10°) mmª. P = Last 2 digits of ID number a = 5th digit of ID number (max value = 3) P Use %3D 4 kN ID # = 18-2363-391 P = 91 a = 6, but use 3 (max) e.g., A C |D B- a - 3 m -3 m
Using method of sections, determine the forces acting in members BC, GC, and GF of the truss shown below. The truss supported by a hinge at A and a roller at E. Summarize the forces indicating tension or compression. Hing e A, Roller E Se where is Your Yeactions A tet 60⁰ B 6.0 m 60° 30 kN G 6.0 m 45 kN 6.0 m ( فهه منصاعدا where FBB f the SE you E Your
Check the midspan deflection of the W12 x 40 girder shown? Neglect the weight of the girder. Assume E = 29 x l0^6 psi and Ix = 310 in^4. Allowable deflection for the total load = (span/240).
Calculate and draw the internal forces created at H section of the bracket beam? a = 500 mm b= 200 mm Px= 15 Kn Py=0 Kn Pz = 10 Kn