2. Design a power supply by specifying their rating to the nearest standard values. C3 (220 VIEO H0 Deg RL Vwdg = 24vde 120 Ohm Eripplepk-pk = 0.75V Standard average current diode rating : 1A, 2A, 3A, 4A, 5A Standard peak current diode rating: 5A,10A, 15A Transformer: 200mA, 250mA, 500mA, 750mA, 1A, 2A, 5A

2. Design a power supply by specifying their rating to the nearest standard values. C3 (220 VIEO H0 Deg RL Vwdg = 24vde 120 Ohm Eripplepk-pk = 0.75V Standard average current diode rating : 1A, 2A, 3A, 4A, 5A Standard peak current diode rating: 5A,10A, 15A Transformer: 200mA, 250mA, 500mA, 750mA, 1A, 2A, 5A

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 4RQ: What is the difference between a diode and rectifier?

See similar textbooks

Similar questions

Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp%3D20V, V1=3 V and V2=10 V. R D2 D1 Vin Vout V1 V2 Maximum voltage of output waveform Minimum voltage of output waveform Ps
consider the figure below that shows an approximated reverse recovery turn-off characteristics for a power diode. Show that the following relation can express the total reverse recovery charge, Qrr = 1/2(trr*ts1) di1/dt =1/2(trr*ts21) di2/dt * ip Isl 1s2! -Ir
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as silicon and D2 as germanium diodes. Input Vpp=20V. V1=5 V and V2=9 V. R www D1 Vin Vout v1 V2 Maximum voltage of output waveform Minimum voltage of output waveform
In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VDC e. PIV (Peak Inverse Voltage) 10:1 Output 115 V mis 60 Hz RL 2.2 k) D, 50μF- All diodes are IN4001. Tund AlMannai EENG261 Page 5/11
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as silicon and D2 as germanium diodes. Input Vpp=20V, V1=3 V and V2=8 V. R www D2 DI Vin Vout V2 Maximum voltage of output waveform Minimum voltage of output waveform
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
Draw vx and v0 according to the input voltages in the circuit shown in the figure. note = R1 = 10Kohm R2 = 1kohm R3 = 1Kohm, the threshold voltages of diodes will be VE = 0.7V.
Determine vo and the required PIV rating of each diode for the configuration in the following figure.
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as silicon and D2 as germanium diodes. Input Vpp=20V, V1=4 V and V2=10 V. R www DZ D1 Vin Vout vi V2 Maximum voltage of output waveform Minimum voltage of output waveform
What is the effect of temperature increase in the reverse saturation current of a diode? Explain briefly
Given an input square wave with +15V and -15V peaks, and bias voltage V of 3V. Diodes are ideal. Resistor value of 330ohms. Draw the output waveform, solve, explain and clearly indicate voltage peak level. HA C V₁ R 10
points) For the circuit shown below, sketch to scale the output V, waveform and draw the transfer characteristic (V. versus Vi), Assume the diodes are ideal. V₁ =15-sin wt Zloks www loks # HIF 4V + Vo