2. For the truss shown below, determine the forces in members UP, QL, JK. Assign a negative value for tensile forces and positive value for compressive forces. Use 3 decimal places accuracy for the final answer. Q R U M H

2. For the truss shown below, determine the forces in members UP, QL, JK. Assign a negative value for tensile forces and positive value for compressive forces. Use 3 decimal places accuracy for the final answer. Q R U M H

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Given the truss and loading shown below, determine the stress at member Al if Pµ = 18.375 Kips and its area is 16 in². Assume that the truss are simply supported at joint M and E. Express your answer in ksi. Use three decimal places. L RM Pu N Pu LK Pu Pu 8@10' = 80' Pu B Pu Pu D J I H G F 8@10' 80' RE
Given the truss and loading shown below, determine the stress at member DF if Pµ = 18.375 Kips and its area is 16 in². Assume that the truss are simply supported at joint M and E. Express your answer in ksi. Use three decimal places. RM Pu Pu 0 Pu Pu 8 @ 10' = 80' Pu B Pu CF Pu et LK J I H G F 8@10' 80' RE
twork Analyze the truss shown using method of joints. The following are the values of the forces: P = 10KN Q = 20 kN R = 30 kN %3D centives Determine the following: CAR a. AE [Select] ements ents b. ČE [ Select] ons C. CD [Select] 40 kN 3 m F F 20 kN + 20 kN E 2 m rations C 5 m Drive A 65 2 5 5 m m m TI Pro P.
A truss is loaded as shown in the figure. The cross- sectional area of each member is 500 mm^2. Hint: Use method of section in getting the axial forces. Use the guide cutting sections. L-6 m+6m- N 25 kN 8 m 50 kN - a 8 m 50 kN 8 m 50 kN 8 m B. 9. Find the axial stress in member HK O 35.34 MPa O 31.12 MPa O 33.34 MPa O 37.12 MPa Question 10 10. Find the axial stress in member HJ. O 125 MPa О 123 МPа O 127 MPa O 129 MPa
Problem 2: Determine the forces in all diagonal and horizontal members of the truss shown below using the method of sections. Determine the force in all vertical members using the method of joints. Hint, the structure is symmetric. The distributed load is transferred to the truss from the roof purlins. State whether the members are tension or compression. Summarize your results on a sketch of the truss. 2.5 k/ft H M K 12 ft A G B C D F 6 @ 12 ft = 72 ft
SITUATION 2: A double-angle tension member, 100 mm x 100 mm x 8 mm is subjected to a tensile load, P= 210 kN. The diagonal member is on a slope 2V:1H and is connected to a supporting beam by a wide tee. S1= 38 mm t1= 16 mm S2= 75 mm t2= 16 mm S3= 100mm t3= 16 mm Allowable strength and stresses: Yield strength, F,= 248 MPa Ultimate Strength, F= 400 MPa Bolt shear strength, F,= 150 Mpa Bolt Tensile Stress, F;= 195 Mpa Bolt Bearing Stress, F,= 1.2Fu Assume that the bolts are equally Loaded. 1. Determine the required "d," of the 3 bolts in shear connecting the double-angle member the wide tee. Round your answer to whole number. 2. Determine the required diameter "d," of the four bolts in tension connecting the wide tee to the flange supporting beam Round your answer to whole number. 3. Design the diameter "d," of the four bolts connecting the wide tee to the flange supporting beam. Round your answer to whole number. 1p S2 S2 t1 t2 t3 S3
The steel truss (E =200 GPa) shown in figure below has a cross-sectional area of 1920 mm². Determine: a. The largest allowable load F if the change in length of member BD is not to exceed 1.6 mm and a factor of safety of 2.5. b. The displacement of support D due to the load calculated in part a. 5m 6m A C F
Consider the truss shown in (Figure 1). Set P₁ = 8 kN, P₂ = 10 kN, and P3 = 6 kN. Figure E ZA B C 3m P₁ P3 3m < 1 of 1 P₂ -3m- 3m D. ✓ Correct ▼ Part D Determine the force in member BF of the truss and state if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FBF = 7.67 HA kN Submit Previous Answers Request Answer ? Review * Incorrect; Try Again; 5 attempts remaining
On the study roof truss shown in the figure, determine the force in element F G and ineach of the elements located to the right of F G. Also, indicate in your answer if the elements are intension or in compression.
Objective: Practice analyzing indeterminate truss systems with bar redundancies. The scissor truss below supports a roof with the factored loads shown. All members are steel shapes with E - 29000 ksi. Complete the following prompts considering this truss. a. Show mathematically that the truss is statically indeterminate. b. If all members have equal areas of A = 8 in.2, determine all member forces and report your results in a table. You should use the principle of virtual work with Member BE as your redundant member. c. Repeat part (b) but modify Member BE only such that its area is A = 2 in.2. Describe the effect of this modification on the member forces in the truss compared to those found in part (b) (both the total member forces in the indeterminate system and those in the statically determinate subsystem). 12' A 14¹. 30 k B '16' 60 k C 16¹- 30 k D 14' E Note: You do not need to show repeated calculations in part (c). Attach any Excel sheets used to facilitate your calculations.
A truss is detailed in figure below. For the given loading, determine the magnitude and nature of the axial forces in members AB, BC and DA, using method of sections. 20 KN D FAB FBG 3m FDA= E 3m F 20 KN -B 3m When submitting your values, consider the required nature. Accordingly, you may need positive or negative force magnitude. KN (C) KN (T) G KN (T) 3m
Q2: Find the permissible distance (X) for the beam shown in figure. If the stresses in tension is 40 MPa and in compresion is 80 MPa. 4kN 4KN. 220 16KN N. A 大 6m 'RB INA: 4 = 20* (o mm