2. Load Tracing For the load-tracing problem below, construct a series of FBDs and show the propagation of loads through the various structural elements. Determine the column loads assuming: DL (decking, flooring, etc.) = 10 psf LL (occupancy) = 40 psf Beam B-2 spans between girder G-3 and column B-2 and beam B-3 spans between girder G-3 and column C-2. 3 d 10' D 101 101 B-2 GI OPEN DECKING DECKING" M G2 B B-3 93 TYPICAL FLOOR FRAMING

2. Load Tracing For the load-tracing problem below, construct a series of FBDs and show the propagation of loads through the various structural elements. Determine the column loads assuming: DL (decking, flooring, etc.) = 10 psf LL (occupancy) = 40 psf Beam B-2 spans between girder G-3 and column B-2 and beam B-3 spans between girder G-3 and column C-2. 3 d 10' D 101 101 B-2 GI OPEN DECKING DECKING" M G2 B B-3 93 TYPICAL FLOOR FRAMING

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Refer to figure SD-07Q007. Given: Slab thickness = 150 mm Dead load = 4.8 kPa (superimposed) Live load = 3.0 kPa Longitudinal beams and girders shown are simply supported at their continuous and discontinuous ends. The plan is that of an office building, if only panel CGDH is occupied. Dimensions are: S₁ = 6.0 m Beams: W350 x 142 Problem 10 Problem 11 Problem 12 S₂ = 6.0 m B E S3 = 6.0 m Girders: W460 x 143 What is the maximum positive moment (kN.m) for beam CG? a. +74.4 b. +77.1 c. +78.2 What is the maximum negative moment (kN.m) for beam GK? a.-51.8 b. -18.0 c. -9.0 What is the maximum positive moment (kN.m) for beam KO due to live load? a. +27.4 b. +21.6 c. +4.5 E H F S4=2.5 m K FRAMING PLAN Fig. SD-07Q007 Ss=2.5 m J 0 N M X d. +75.3 d.-13.5 d. +2.3 S6=2.5 m
Define Load Combinations for ASD
Compute the load diagram
What is the maximum permissible span for a 6 inches thick one-way solid slab? k Architects' Studio Companion design aid diagrams below. The building construction is cast-in-place conventionally. reinforced concrete. STECAT CONCE ONE WAY OLDIL 200 CAST CONCE COLUMNS NORMAL RETORT www 9 feet 13 feet 16 feet 20 feet han 15 SECAST CONCRETE BEANS AND GIRDERS 42 80 KURANG DALAGAN Des
What is the collapse load of beam as shown in figure? A B 10M₂ L 12Mp L 3M, 1/2 W ↓ to C D M₂ 1/2 16Mp L SMp L
Discuss Structural dead loads
Define Earthquake loads (E)
Problem Exercise From the following figure, find the number of 10 mm lateral ties and tie wire if there are 36 columns with cross sectional di- mensions of 60 x 90 cm. at 12.00 meters long per column. 10 - 25 mm main reinforcement 90 m Lateral Ties 60 m. CROSS SECTION .60 m. FIGURE 3-17 o lo
Load calculation :
Instruction: Follow Given-Required-Solution format for your computation. Complete FBD for full credit. Problem: The concrete pier is subjected to soil pressure that causes the line loads shown. Determine the resultant of the loading and find the y-coordinate of the point where the resultant crosses the y-axis.
Q4. With the aid of sketches, critically discuss the installation of an independence type of scaffold system in building construction. The discussion should highlight the function of each component members of the system and necessary safety precaution that need to be taken during the installation.
3. Load Tracing For the framing plan below, find out the reactions of the beams and girders shown in the plan. The loads on the plan are as follows: Snow Load Concrete (4" slab) Steel Deck Mechanical equip. = 50 psf = 150 pcf = 5 psf = = 10 psf Suspended Ceiling = 5 psf Q-6 I -6 @ 6.67' = 40- H 33 B3 I H 2 @ 10' 20' + 5 @ 8'=40' B2 G1 B4 C2 B I I 13 G4 G2 G3 B1 C-I- I. C3 40' - 20'-