2. The T-shaped column as shown is reinforced with 5-28 mm and 2-25 mm diameter bar with fy = 415 MPa. f'c=27 MPa a) Determine the location of plastic centroid from the extreme left fiber b) Determine the factored moment due to the factored load of 1800 kN applied at 312 mm from extreme left fiber c) Determine the factored moment due to the factored load of 1800 kN applied at 100 mm from extreme left fiber 75 mm 65 mm 100 mm 100 mm 100 mm 200 mm 150 mm

2. The T-shaped column as shown is reinforced with 5-28 mm and 2-25 mm diameter bar with fy = 415 MPa. f'c=27 MPa a) Determine the location of plastic centroid from the extreme left fiber b) Determine the factored moment due to the factored load of 1800 kN applied at 312 mm from extreme left fiber c) Determine the factored moment due to the factored load of 1800 kN applied at 100 mm from extreme left fiber 75 mm 65 mm 100 mm 100 mm 100 mm 200 mm 150 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three aluminum members, each having a cross-sectional area of A=1480 mm². Assume a-1.5 m, b-6.5 m, and c-3.8 m. If P-55 kN and Q-90 kN, determine the normal stress in each member. L. Answers: JAB" OBC= MPa (C) MPa (T)
Use principles of steel solution. explain each step STEEL DESIGN Beam CD is simply supported at C and D. 1. Compute the maximum bending stress of beam CD. 2. By investigation, the beam CD has an allowable bending stress, Fb = 94MPa. To strengthen the beam, 2 cover plates of 10 mm thick are to beadded on the top and bottom flanges as shown in Figure ST - 903. 3. Compute the required width of the cover plates. 4. Compute the cut off point of the cover plates from each support at C and D.
Question 5 Match the answers in the columns. v Maximum Shear stress of a cross section. A. using an l-section instead of a rectangular section. v Maximum Bending stress of a cross section. B. Tension and bending force. C. 1m form the supports - v If a simply supported beam is subjected to a distributed load, where are you most likely to find tension bending cracks. D. At Midspan - v Ifa simply supported beam is subjected to a distributed load, where are you most likely to find shear cracks. E. Midspan at the bottom v The bending stress in a section can be reduced by using a F. Midspan at the top v Shear stress can be increased by the width of a section. G. At the supports. v The shear force in fasteners. H. Reducing the width of a section. v Moment couple on a section. 1. using a rectangular section instead of an l-section J. Shear flow K. Increasing the width of a section. L. Only at the section sides touching the NA M. In between the NA and the top/bottom fibres N. Usually at the NA…
The rigid beam is supported by three suspender bars. Bars AB and EF are made of aluminum (Eal = 70 GPa) and bar CD is made of steel (Est = 200 GPa). If each bar has a cross-sectional area of 450 mm² and P = 50 kN, determine the following for each bar: a) Stresses (in MPa) b) Elongation (in mm) al B st D C al 0.75 m 0.75 m 0.75 m 0.75 m 2P F 2 m E 1/1
The rigid beam is supported by three suspender bars. Bars AB and EF are made of aluminum (Eal = 70 GPa) and bar CD is made of steel (Est = 200 GPa). If each bar has a cross-sectional area of 450 mm² and P = 50 kN, determine the following for each bar: a) Stresses (in MPa) b) Elongation (in mm) al B st D al 0.75 m 0.75 m 0.75 m 0.75 m 2P F 2 m E
The wood beam has a rectangular cross section in the proportion shown. The allowable bending stress iss =10 MPa. 500 N/m 1.5 b OB - x m 2 m 2 m Calculate the centroid of the cross section of the beam O (1.5b, 1.5b] O (1.5b/2), (1.5b/2)] O (0.(1.5b/2)] O (0,0) [(1.5b/2), 0] O (0, 1.5b)
Determine the maximum magnitude of load P that can be applied to the truss. The maximum allowable tensile force in the members of the truss is (Ft) max = 5.2 kN, and the maximum allowable compressive force is (Fe) max = 3 kN. Take d = 2 m. (Figure 1) Figure 1 of 1 E d/2 C PV d/2 <
- Determine the moment of intertia about the centroidal x-acid (in mm^4) - Determine the centroid location of the cross-section from the bottom fiber of the section (in mm) - Determine the bending stress at point H. Include a negative sign if compression. (in MPa.) - Determine the section modulus in reference to the bottom fiber (in mm^3) - Determine the maximum bending stress produced in the cross sectio. Include a negative sign if compression. (in MPa.)
The T-beam in the floor system has a slab thickness of 90 mm and supported by beams 6.5 m span. The beam is casts monolithically with the slab. The spacing of beams is 2 m on centers and width the web is 400 mm. The effective depth of the beam is 600 mm. It is reinforced at tension side with 8-28mm Φ bars. fc’ = 28 MPa, fy = 415 MPa 1. Which of the following most nearly give the effective width of the flange? a. 1565 mm b. 1305 mm c. 1275 mm d. 1625 mm 2. Which of the following most nearly gives the depth of compression block? a. 62.25 mm b. 52.86 mm c. 60.26 mm d. 58.29 mm 3. Which of the following gives the nominal moment capacity of the beam? a. 1461.25 kN/m b. 1156.36 kN/m c. 1163.15 kN/m d. 1172.58 kN/m
If P= 8.571 kN, Determine the stress in member CEassuming that the area in steel is 24 mm2.Show FBD
Determine if the axial stress in nember CF if the area of each member is 75 mm^2. Indicate if T or C.
The members of the truss are 25mmx50mm in cross section. Determine the maximum load P that can be applied so that the stresses will not exceed 100 MPa in tension or 70 MPa in compression. See figure 101. Figure 101 A 0 2m P B 2.5m 1.5m C