20 kN 12 kN A В M = 10 kN-m %3D 4m 4m 4m Figure Q1 (b)

Q: Calculate Tension BD if P = 100 kN. ... 1m 2.5 m D 250 N P -1.5 m- 2 m 1.5 m Use the editor to…

A: Find the tension in BD.

Q: Q4: An inclined circular gate (AB) with hinge support at (B) and the weight of gate (12kN).…

A:

Q: Find the pressure due to a column of mercury 80 cm high.

A: AS PER COMPANY POLICY, ONLY ONE QUESTION CAN BE SOLVED AT A TIME. FOR SOLUTION OF OTHER QUESTIONS,…

Q: 29. A point mass of 100 kg is dropped onto a massless elastic bar (cross-sectional area = 100mm²,…

A:

Q: The system shown is subjected to three axial forces P₁ = 250 kN, P₂ = 400 KN and P3 = 275 kN. What…

A: To find: The total change in length due to loading. Given: The length of bar AB is  lAB=1 m. The…

Q: The tube, shown below, is supported by two cables (AB) and (AC). A force F = 600 lb is applied in…

A:

Q: A homogeneous rectangular gate AB 2.6 ft wide and 10 ft long. Friction in the hinge is negligible.…

A:

Q: For figure below, the tension in the * cable is 0.25 m A 25° B 0.5 m - 0.12 m 1.5 m 14 &N

A:

Q: 1.5 kN/m Given the figure at the right, solve for the support reactions. 10kN.m 30 3KN 14KN 1.2m…

A:

Q: Problem 2 (b) : Problem Statement and Question 2 (b) (b) A car plunged into a lake (p=1000 kg/m³)…

A: Given data: ρ=1000 kg/m3hf=hr=1.2 mwf=1 mwr=0.8 mH=10 m Need to determine the hydrostatic force on…

Q: Q4) A hydraulic system is shown in figure Q4. Assume the system is in equilibrium state (There is no…

A:

Q: For the system shown in Fig. 1, determine the generalized physical properties m", c", k", and the…

A: We have to calculate the m,k,c explaining with physical properties and Dimensions

Q: A person holds horizontally a 20 Kg bar with both hands (see Figure 2.1). The hands are 1.5 m apart…

A:

Q: In the figure below, all the bearings are movable bearings and the C bearing is in an inclined…

A:

Q: A machine component 1.5 m long and weight 1000 N is supported by two own in Fig. 2.2 given below.…

A: Given:- Total Length = 1.5 m Weight = 1000N Angel at B and C respectively = 60 and 45

Q: ka 2 ki P Rigid bar k3 for the system shown in the figure, which of the following statements are…

A: from the figure , we see that , point 1,2,3,4 are rigid on the wall , so they can't move while…

Q: Figure Q2[a] shows a shaft supported by three smooth journal bearings at A, B, and C. Given: F,-923…

A:

Q: For figure below, the tension in the cable is 0.25 m 25° В 0.5 m 0.12 m 1.5 m 14. «N 5 m

A:

Q: The vertical reaction in the hinged support shown in the figure is Blank 1 N. 200 N 200 N B E 2 m 2…

A:

Q: Parabola 1.2 cm dia. V1= 8 m/s Water %3D P1 = 150 kPa P2 = 110 kPa %3D

A:

Q: Draw the free body diagrams for each part in the figures below: P 4P 4P 2P 0.5m 0.5 m m' 1.5 m 1.5 m…

A: Answer is given below

Q: 0 0.3 m 70⁰ m 4 kN 15 kN m 0.5 m 6 kN 0.3 m PROBLEM 2/71 1.5 m 10 kN

A: When an amount of force act on an object it has the tendency to rotate the object about a point,…

Q: 50 kN 30 kN A 2 m 1 m 3 m

A: For solution refer below images.

Q: 3. A 127-kg stunt man throws himself off a 18-m tall building onto a trampoline. The trampoline…

A: mass of the stunt man (m)=127kg  length of building =18m stretch in trampoline (x)=1m assuming…

Q: a ladder whose length L is 12 m and whose mass is 45 kg rests against a wall. Its upper end is a…

A: Given, L = 12 m M = 45 kg h = 9.3 m m = 72 kg

Q: An unknown weight falls by 30 mm onto a collar rigidly attached to the lower end of a vertical bar 4…

A:

Q: Draw V & M diagram 800 Ib 1000 Ib 4000 Ib 200 lb 4' 2' 6' 4' 2' R2

A:

Q: Q2) Figure 2 shows a rope that is stretched between points A and C, there is mass m at point B.…

A: Given data: The magnitude of mass m = 20 kg. The height h = 2 m. The length d = 3 m. The angle…

Q: 8.6 m 30° hc hp F Hinge YP Water 5m Gate Ic= a/12 Figure 4 An inclined rectangular gate submerged in…

A:

Q: Prob. # 3] The mass (Figure P3), m = 0.4 kg, is suspended from two springs in series with stiffness…

A:

Q: A body of dimensions 0.5 m x 0.5 m x 1.0 m and sp. gr. 3.0 is immersed in water. Determine the least…

A:

Q: Diving board A Length : 4m Width : 0.45m Thickness : 0.03m Inertial of moment: I=bh 1=(0.45)(0.03)"…

A: First of all note down given data in the question. Like length, width, hight. Etc

Q: A caisson for closing the entrance to a dry dock is of trapezoidal from 16 m wide at the top and 12…

A:

Q: Question 2. The system shown below is composed by a flexible cable, a bar and weight with mass…

A:

Q: M2 N (Steel tame) =60 loN/m: K2=45 N/m K3=30 k/m : M,70 kg : M2=140 kg Figure P8 M Problem 9 Figure…

A: other subject of mass m by x amount from equlibrium position-Kinetic energy-K.E=12mx2       x=dxdt

Q: Member AB (helical spring) and Member AC (axial rod) are carrying a weight at point A. Member AB has…

A:

Q: Oil sp gr 0.90 Gate-4 ft wide r= 2 ft F Water 2ft 2 ft S= 3.0 Figure 2.74 Problems 2.84-2.86.…

A:

Q: The tube, shown below, is supported by two cables (AB) and (AC). A force F = 600 lb is applied in…

A:

Q: AB represents a uniform horizontal shelf of weight 30N which is at X and Y. Blocks are placed along…

A:

Q: The hydrostatic force on the gate and its position as function of h and show its direction on the…

A: Data given - d = 1 m  h = 2.5 m  b = 2.2 m  Density of water = 1000 kg/m3 g = 9.81 m/s2     As per…

Q: Q2) Several water pipes intersect at the junction box illustrated in Figure. Determine the force…

A:

Q: Q4) A solid plastic ball of density 6.00 x 102 kg/m and radius 2.00 cm is attached by a lightweight…

A: Given: The density of solid plastic ball= 600 kg/m3 The radius of the ball = 2 cm

Q: Given the loading criteria in the figure below, find all reaction forces. |80 kN 30 kN/m 2m 3m 2m

A: A uniformly distributed load (UDL) is a load that is evenly distributed throughout the whole…

Q: F2 (2 Q1) Axial displacement of point C in the system shown on the left is 0.01 cm. Find the maximum…

A: Write the given value using suitable variables. Here ΔlC signifies point C axial displacement, F2…

Q: Draw the shear and moment diagrams for each of the beams shown.

A: given beams

Q: 1.17. An unknown weight falls by 30 mm onto a collar rigidly attached to the lower end of a vertical…

A:

Q: Cable - B. 30° Fig. P4.2 0.1 m

A:

Q: Q2: For the system shown in figure, all chains are of negligible weight, if the tensile force in…

A:

Q: ven m-50kg and the following dimensions: AB = 1m, BC 3m, angle ACD 30 degrees Draw a free body…

A:

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.