3) The simply supported beam with the cross-section as shown supports a total uniformly distributed load of 4P and 2P and concentrated load P as shown in the figure. Determine the maximum allowable value of P if the allowable flexural stresses are limited to 35 MPa in tension and 150 MPa in compression respectively. 1m P B 4P ** potuty, :LI 175 3m 200 1m IC D 2P + 1m (Dimensions in mm)

3) The simply supported beam with the cross-section as shown supports a total uniformly distributed load of 4P and 2P and concentrated load P as shown in the figure. Determine the maximum allowable value of P if the allowable flexural stresses are limited to 35 MPa in tension and 150 MPa in compression respectively. 1m P B 4P ** potuty, :LI 175 3m 200 1m IC D 2P + 1m (Dimensions in mm)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An aluminum strut has a cross section referred to as 30 mm 30 mm a deep hat. Locate the centroid ỹ of its area. Each segment has a thickness of 10 mm. 100 mm 80 mm
The simply supported beam in Fig. has a composed cross section. Determine the values and locations of the maximum tensile and compressive bending stresses. E2-3867 Kpsi, El= 29000 Kpsi 400 lh/t 1000 1b 6 inch D E1 0.8 inch E2 8 inch 10 n
Q4) A cast iron beam is of I – section as shown in Figure (3). The beam is simply supported on a span of 5 m. If the tensile stress is not to exceed 20 N/mm2, find the safe uniformly load which the beam can carry. Find also the maximum compressive stress. I 80 mm- 20 mm 3 169.34 mm 200 mm 2) 20 mm A 90.66 mm 40 mm 100 mm Figure (3)
A cast iron beam is of I– section as shown in Figure (3). The beam is simply supported on a span of 5 m. If the tensile stress is not to exceed 20 N/mm2, find the safe uniformly load which the beam can carry. Find also the maximum compressive stress. -80 mm- 20 mm 169.34 mm 200 mm 20 mm N 90.66 mm 40 mm 160 mm Figure (3)
Q1:If allowable stresses are o, 165MPa, o, 100MPa T= 70MPa determine max. value of W. CM 300mm Im 4m Im pe T 100mm 100mm 300mm
The shown plate is 60 mm thick and it is made of Magnesium Am1004-T61. The plate is fitted between the rigid frictionless supports as shown and at T, = 20°C it is stress free. Find the stresses in the x and y directions when the temperature increases to T, = 58°C. %3D 150 mm 150 mm Select one: O x: 0 MPa, y: 42.864 MPa Ox: 22.1 MPa, y: 44.2 MPa Ox: 0 MPa, y: 44.2 MPa Ox: 0 MPa, y: 17.8 MPa O x: 13.2 MPa, y: 44.2 MPa Ox: 0 MPa, y: 67.4 MPa 3:10 PM O G 4) ENG 1/31/2021
An aluminum alloy [E = 10,300 ksi] tee‐shaped bar is used as a beam. Thecross-section of the tee shape, shown in the figure below, has a total depthof d = 7.5 in. The centroidal z-axis of this cross-section is located 2.36 in.above point H. The beam spans in the x-direction and it bends about the zcentroidal axis. A strain gage is affixed to the side of the tee stem at adistance c = 1.25 in. below the top surface of the tee shape. After loads areapplied to the beam, a normal strain of ɛx = −810 μɛ is measured by thestrain gage. What is the bending stress at point H?
Compute for the maximum allowable distributed load o that can be applied to the simply supported beam as shown in Figure M-Va. The beam's cross section is detailed in Figure M-Vb. @(N/m) Allowable Stresses: Fiber Stress = +13.5 MPa / -12 MPa Transverse Shear Stress at NA = 900 kPa Transverse Shear Stress at Junction 800 2 m Figure M-Va 2 m Draw the flexural and shear stress distributions of the cross section. T 40 40 40 Figure M-Vb 40 120 mm
A cantilever beam with a ‘T’ shaped cross-section is loaded with a distributed load as shown below.The intensity of the distributed load is 100N/mm. b = 6.25mm and c=6.25mm.Parameter Description Value UnitsL - Beam length 250 mma - Width of the flange 80 mmd - Height of the web 75 mmσ - Yield stress 250 MPaYou are tasked with ensuring the beam can withstand the applied loading. To do this you must:a) Calculate the centroid for the given cross-section. Your value of ?ത should be measured fromthe bottom of the section. Determine an expression for Q (statical moment of area) for thegiven shape. The expression(s) for Q should be in terms of the variable, y, measured from thebottom of the section. b) Create a graph of the shear and bending stresses at the fixed support (B) over the crosssection. The stresses should be plotted as a function of y, measured from the bottom of thesection.
For the truss shown, calculate the stress in area of each member BD. The cross-sectional member is 1200mm². 4m B 6m U 3m 4m E 3m 100KN 200KN F M FLSNI
A steel structural member is to be used as a column 5 m long. The column is to be pinned at both ends for bending about X-X axis and fixed at one end and pinned at the other for bending about Y-Y axis. The properties of the member section are as follows:E= 200 GPa, yield stress= 350 MPa, Ixx = 222 x 106 mm4, Iyy = 72.71x106 mm4 and A= 12.33 x 103 mm2Using Perry-Roberston equation, calculate the buckling stress and the corresponding load
2.3-7 A steel bar 2.4 m long has a circular cross section of diameter d, = 20 mm over one-half of its length and diam- eter d, = 12 mm over the other half (see figure part a). The modulus of elasticity is E = 205 GPa. (a) How much will the bar elongate under a tensile %3D %3D load P = 22 kN?