3. دیا a) Explain using appropriate equations why magnetic field lines are confined to the core of a magnetic circuit. Your answer should have a maximum of 100 words. b) In the circuit of Figure Q3b, find the voltage across the current source given that the reverse saturation current of the diode is 2 x 10-¹2 A. Assume the circuit is at room temperature and the diode is ideal. I mA 2 km2

3. دیا a) Explain using appropriate equations why magnetic field lines are confined to the core of a magnetic circuit. Your answer should have a maximum of 100 words. b) In the circuit of Figure Q3b, find the voltage across the current source given that the reverse saturation current of the diode is 2 x 10-¹2 A. Assume the circuit is at room temperature and the diode is ideal. I mA 2 km2

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
A diode circuit is given in the below figure, in which two diodes are connected in series and their saturation currents are Is1 =10-¹6 A and Is2 =10-¹4 A. If the applied source voltage is 1 V, calculate the currents IDI and ID2 and the voltage across each diode VDI and VD2. IDI Ī Vpl + D₂ VD2
For the circuit shown in figure 1, the diodes is in complete model and the resistance of both diodes are 5 Ohm. Find the current in the resistance RL. When the both switch S1 and switch S2 are ON. v1= 6V, V3 =3 Vv2=12 V.
In the circuit given in the figure, find the current passing through the diode in mA since R1 = 4.95Kohm, R2 = 2.50Kohm, R3 = 1.69Kohm, R4 = 5.44Kohm, VCC = 13.00V and the diode is silicon?
Q1 Assume that each diode has a turn-on voltage 0.7V in the circuit shown in Figure Q1. By using the constant voltage drop model: 1kN D1 D2 2kN 4k2 6V 3V 4V Figure Q1 a) Show that it is not possible that D1 is on and D2 is off. (Hint: show a contradiction) b) Show that both D1 and D2 are on.
How do I calculate the dynamic resistance of a zener diode with the following set of values given please? The circuit in figure is the circuit in question I am trying to solve this for please. Vin(DC) = 10V vin(ac) = 0.05sin(wt) Vz(voltage of diode) = 4.5V R1 = 1000 ohms
Calculate the currents passing through diodes D1 and D4 in the circuit given below (Figure 1)?(All diodes are silicon).
A- If V, is a sinusoidal voltage with Vm = 40 V, and V= 15 V. Plot the waveform of the output voltage in each of the following clippers circuits assuming ideal diodes. B- Repeat part (A) if the diodes are silicon diodes. R R R (a) (b) (c) (d)
Figure Q2(a) shows the characteristic curve of a Zener diode. Analyse the characteristic curve to identify the approximate minimum Zener current Izk(min) and the approximate Zener voltage, Vz at IZK. -10 -9 -8 -7 -6 -5 -2 -1 Vz (V) + 1 3 4 6 7 8 Iz (mA) Figure Q2(a) Analyse the circuit in Figure Q2(b) to identify the minimum input voltage required to keep the diode in Zener region based on the values of the minimum Zener current and the approximated Zener voltage found in Question 2(a). R 1k2 VIN Figure Q2(b)
Draw vx and v0 according to the input voltages in the circuit shown in the figure. note = R1 = 10Kohm R2 = 1kohm R3 = 1Kohm, the threshold voltages of diodes will be VE = 0.7V.
Using the ideal diode model, find the output voltage for the input voltage of the following circuit and graph it in detail. (a) (b) R₁ D₁ www ww R3 D2 (a) R₁ D₁ www + + D2 R2 vo Vo R₂ (b)