3. The sequence b(k) = {1, 0, 0, 1, 1, 0} is transmitted at bit rate of R, =1 Kb/s using an FSK digitalsystem, the frequency f1 = 3 KHz and fo = 1 KHz. The carrier signal c(t) is one cycle/Ts, determinethe following;%Da- Calculate the carrier frequency fc.b- Calculate the frequency deviation Af.c- Calculate the modulation index h.d- Sketch the baseband signal m(t).e- Sketch the transmitted passband signal XFSK(t).

According to the question, for FSK digital system message bit b(t)={1, 0, 0, 1, 1, 0} Bit rate=1…

3. The sequence b(k) = {1, 0, 0, 1, 1, 0} is transmitted at bit rate of Rp =1 Kb/s using an FSK digital system, the frequency f1 = 3 KHz and fo = 1 KHz. The carrier signal c(t) is one cycle/Ts, determine the following; %3D a- Calculate the carrier frequency fc. b- Calculate the frequency deviation Af. c- Calculate the modulation index h. d- Sketch the baseband signal m(t). e- Sketch the transmitted passband signal XFSK (t).

3. The sequence b(k) = {1, 0, 0, 1, 1, 0} is transmitted at bit rate of Rp =1 Kb/s using an FSK digital system, the frequency f1 = 3 KHz and fo = 1 KHz. The carrier signal c(t) is one cycle/Ts, determine the following; %3D a- Calculate the carrier frequency fc. b- Calculate the frequency deviation Af. c- Calculate the modulation index h. d- Sketch the baseband signal m(t). e- Sketch the transmitted passband signal XFSK (t).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1) We need transmission effiency (n) 2) Minimum and Maximum frequency values of the FM signal. ( kHz)
Example 1 20M₂ Amplitude of carrier signal is given 10 V, and freq? This carrier is modulated by 16 kHz signal and modulation index is 0.6. Devive the DSB-LC (Full AM) 2 terms And Sketch freq domain single Sided DSB -SC SSB (USB) SSB (LSB) - 3 terms
Which is not true in simultaneous modulation? a. the AM signal is consisting of more than 1 pair of sidebands and a carrier signal b. the AM bandwidth is much wider than single tone modulation c. the effective modulation index is higher than the highest individual modulation index d. the effective modulation index can be lower than any of the individual modulation index
For the above given signal each bit is separated by a vertical line. If duration of a bit is given as 60 ms, which answer is correct? O a. Data: 1 01101011001 Modulation Rate: 0,4 KBaud Encoding: Differantial Manchester O b. Data: 1 01101011001 Modulation Rate: 0,03 MBaud Encoding: Differantial Manchester O c. Data: 110101101110 Modulation Rate: 0,2 Kbps Encoding: Differantial Manchester O d. Data: 1 01011011100 Modulation Rate: 0,4 MBaud Encoding: Manchester Oe. Data: 1 10101101110 Data Rate: 0,02 Kbps Encoding: Manchester
please answer with solution Determine the “M” value and number of data bits that can be represented by a single symbol using PSK where the possible phase values per symbol can be {π/4, 3π/4, 5π/4, 7π/4}. a. M=2, N=1 bit per symbol b. M=4, N=2 bit per symbol c. M=6, N=3 bit per symbol d. M=8, N=3 bit per symbol
1. With the help of Octave program perform the Modulation and Demodulation (AM) of information signal with carrier signal, through subplots with following signals a. Modulating signal b. Modulated signal c. Demodulated signal
Please help me with my homework. Thanks! The course subject is Fundamentals of Electronic Communications. 2. A 75 MHz carrier having an amplitude of 50 V is modulated by a 3 KHz audio signal having an amplitude of 20 V. Determine the modulation index, % modulation, fusb, flsb, AM equation.
What are the similarities and differences between the information signal m (t) obtained as a result of demodulation and the original information signal m (t) on the modulation side? (the demodulated signal is irregular one)
What are the data rate limits? Calculate the maximum bit rate of noiseless channel with a bandwidth of 4000 Hz transmitting a signal with three signal levels.
Which of the following is not an effect caused by multipath in radio channel? a) Rapid changes in signal strength b) Random frequency modulation c) Power of base station d) Time dispersion
3. Some GPS receivers use 1 bit ADCS (Analog-to-digital Converters) to sample and quantize the signal i.e. the output of the ADC is simply 2 quantization levels: -1 or +1. This is typically done to save on power. (a) What is the quantization SNR? How does it compare to typical thermal noise SNR of a GPS signal before correlating with the CDMA code? (b) Justify, how come it is possible to sample the signal using a single bit and still get good performance.
Example1: An analog signal has a bit rate of 8000 bps and a baud rate of 1000 baud. How many data elements are carried by each signal element? How many number of conditions ? Example2: We need to send data 3 bits at a time at a bit rate of 3 Mbps. The carrier frequency is 10 MHz. Calculate the number of levels (different frequencies) and the baud rate