In Fig. 6-38 the maximum lining pressure for any point on the brake is to be limited to 100 psi; μ = 0.2. Find the torque capacity of the brake and the value of force P.Ans. T = 9,080 in-lb, P = 487 lb 39. In Fig. 6-38 the maximum lining pressure for any point on the brake is to belimited to 100 psi; u = 0.2. Find the torque capacity of the brake and the value offorce P.Ans. T = 9,080 in-lb, P = 487 lb.303030Fig. 6-38. Problem 39.

Given DataP=100psi=689476Par=8''=203.2b=212''=63.5mmHere the conersions we tae…

39. In Fig. 6-38 the maximum lining pressure for any point on the brake is to be limited to 100 psi; µ = 0.2. Find the torque capacity of the brake and the value of force P. Ans. T- 9,080 in-lb, P = 487 lb. 30 30° 30° 30 Fig. 6-38. Problem 39.

39. In Fig. 6-38 the maximum lining pressure for any point on the brake is to be limited to 100 psi; µ = 0.2. Find the torque capacity of the brake and the value of force P. Ans. T- 9,080 in-lb, P = 487 lb. 30 30° 30° 30 Fig. 6-38. Problem 39.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The brake shown in Fig. 16-8 is 300 mm in diameter and is actuated by a mechanism that exerts the…

Q: 3.A multiple disc clutch has three discs on the driving shaft and two on the driven shaft, providing…

A: Answer: The maximum axial intensity of pressure between the discs: 0.12665 MPa.

Q: In a thrust bearing, the external and the internal diameters of the contacting surfaces are. 19 mm…

Q: An engine developing 50 hp at 1200 rpm is fitted with a cone chutch built into the flywheel. The…

A: Write the given data in the problem. P=50 hp N=1200 rpm d=15 in μ=0.30pn=13 psi α=12° Here, α is…

Q: The figure shows an internal rim-type brake having an inside rim diameter of 11 in and a dimension…

A: Brake is a mechanical device which absorbs energy from the moving system or any mechanism with the…

Q: (Q2) A gear box for mine shaft lifts a load of 16.7 kN using a pulley of outside diameter 720 mm and…

Q: aded with uniform vertical thin r case has a total weight of 1000 N of static friction 0.3 with the…

Q: • H.ws: A single block brake, as shown in Fig. 25.38, has the drum diameter 250 mm. The angle of…

Q: Brake Design H.W (1):A single block brake, as shown in Figure, has the drum diameter 250 mm. The…

A: Consider the free body diagram shown below for the drum. The equivalent friction coefficient can be…

Q: Q5. The drum of a simple band brake is 450 mm. The band embraces 3/4th of the circumference of the…

Q: An automobile single plate ciutch consists of a pair of contacting surtaces. The inneOr and outer…

Q: Q2 ) A cone clutch is to transmit 10 KW at 600 r.p.m. the cone has a face angle of 10° The width of…

A: Given, Power transmitted , P =10 Kw Speed, N =600 rpm Cone angle = 10 degree maximum pressure , Pr…

Q: Let the curve for and f for a 3-in. diameter x 6-in. long bearing be a through straight line passing…

A: Given, Load, W=1400lbs1lbs=4.448NW=1400lbs=6227.2NRpm, N=1000rpmFor the friction corresponding to…

Q: The figure shows an internal rim-type brake having an inside rim diameter of 11 in and a dimension R…

A: Brake is a mechanical device which absorbs energy from the moving system or any mechanism with the…

Q: H.W (2):A single block brake, as shown in Fig. 25.39, has a drum diameter of 720 mm. If the brake…

A: Given, d=720 mm=0.72 m T=225 N.m μ=0.3 The radius of the drum, r=d2=0.36 m The torque in the drum is…

Q: The figure shows an internal rim-type brake having an inside rim diameter of 300 mm and a dimension…

Q: An external long shoe drum brake is illustrated in Figure 2. The face width of the shoes is 60 mm…

Q: For this long shoe break system, we adopt the hard surface assumption with the maximum pressure of…

Q: The figure shows an internal rim-type brake having an inside rim diameter of 11 in and a dimension R…

A: Brake is a mechanical device which absorbs energy from the moving system or any mechanism with the…

Q: The following parameters are given for the journal bearing. µ = 4 ureyn, N = 651 rev/min, W = 851…

A: The above question based on journal bearing. To calculate the parameters we will use following…

Q: Q2 ) A cone clutch is to transmit 10 KW at 600 r.p.m. the cone has a face angle of 10. The width of…

Q: The figure shows an internal rim-type brake having an inside rim diameter of 11 in and a dimension R…

A: Note: As per our guidelines we are supposed to answer only the first 3 sub-parts. Kindly repost…

Q: The figure shows an internal rim-type brake having an inside rim diameter of 11 in and a dimension R…

A: Brake is a mechanical device that absorbs energy from the moving system or any mechanism with the…

Q: Q1) The mean diameter of the driving pulley for a vee-belt drive with two belts is 110 mm. The…

A: dmean=110 mmP=4.4 KWN=1500 rpmμ=.32Angle of lap θ=160°A=120 mm2

Q: A rolling bearing has a number 6315 and rotating with n= 50 rev/m This bearing has a radial force…

Q: The following data refer to an internal expanding shoe brake shown in Fig. 15.16: Force F on each…

Q: The figure shows an internal rim-type brake having an inside rim diameter of 11 in and a dimension R…

A: Given data Inside diameter = 11in Face width =1.25 in R=3.5 inb=1.25 inf=0.32r=112=5.5 in and…

Q: A cone clutch is to transmit 10 KW at 600 r.p.m. the cone has a face angle of 10◦ The width of the…

A: Given data:

Q: A differential band brake shown below is being considered for use and requires a brake torque of…

Q: The factor of safety against slipping in the friction clutch = 1.3; coefficient of friction=0.4;…

Q: estion 6 A block brake is used to stop a drum of 400 mm diameter. contact angle is 90°. The…

A: Given:d=400 mmμ=0.3

Q: Q10/ A single block brake, as shown in figure, has the drum diameter 250 mm. The angle of contact is…

Q: +120 - -300- Q12/ The simple band brake shown in figure is applied to a drum of diameter 240 mm. The…

Q: The figure shows an internal rim-type brake having an inside rim diameter of 11 in and a dimension R…

A: Brake is a mechanical device which absorbs energy from the moving system or any mechanism with the…

Q: Q5: The block brake shown in figure has a face width of w=50 mm. The coefficient of friction is 0.25…

Q: The figure shows an internal rim-type brake having an inside rim diameter of 11 in and a dimension R…

A: Brake is a mechanical device which absorbs energy from the moving system or any mechanism with the…

Q: The pedal system shown in the figure is exerted by both an up and down mechanism. These forces are…

A: Given: The maximum load, Fmax = 350*89/10 = 3115 N The minimum load, Fmin = - 150*89/10 = - 1335 N…

Q: The band of a brake has a contact angle of 18° deg. If the pulls on the bands are 275 kg and 100 kg,…

Q: 7. The hand-brake shown in Figure 1 below is used on a wall crane. The brake drum is 600 mm…

A: Find the least force at lever.

Q: The figure shows an internal rim-type brake having an inside rim diameter of 11 in and a dimension R…

A: Given data Inside rim diameter =11 in Face width = 1.25 in Actuating force =205 lbf f =0.32…

Q: A caliper brake is required for the front wheels of a sports car with a braking capacity of 820N m…

Q: A schematic of a clutch-testing machine is shown. The steel shaft rotates at a constant speed w. An…

A: Torsional loading Those load which imparts the turning moment or the torque, is known as…

Q: i need the answer quickly

Q: The following data refer to an internal expanding shoe brake shown in Fig. 15.16: Force F on each…

Q: Q2/ A conical clutch an included angle of 60º. the outer radius and inner diameters are 80 and 20 cm…

A: Given data, Since, the clutch is of two halves. So, the cone angle of the clutch is α=602α=30° Outer…

Q: T= 16 R = (rl+ -1 =nd+8+ 0.158 W p.A 8 = Gd 300 200 Q3: A block brake with a torque of 250 N-m. Its…

A: NOTE:- As per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost…

Q: (9) A single thread trapezoidal metric thread has a pitch of 4mm &has a mean diameter of 18mm. It is…

Q: A simple band brake operated by an air cylinder that applies a force Fof 300 N. The drum radius is…

Q: QUESTION 3: [Frietion clutch] [16| A cone clutch is to transmit 7.5 kW at 900 rpm. The cone has a…

A: Given Data → P=7.5Kw N = 900rpm θ=12° Write the expression for T T =60000×P2πN T =…

Q: in the figure is a single block brake. The intensity of pressure between the block and rum is 1.5…

Question

100%

In Fig. 6-38 the maximum lining pressure for any point on the brake is to be limited to 100 psi; μ = 0.2. Find the torque capacity of the brake and the value of force P.

Ans. T = 9,080 in-lb, P = 487 lb

39. In Fig. 6-38 the maximum lining pressure for any point on the brake is to be
limited to 100 psi; u = 0.2. Find the torque capacity of the brake and the value of
force P.
Ans. T = 9,080 in-lb, P = 487 lb.
30
30
30
Fig. 6-38. Problem 39.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Similar questions

Q10/ A single block brake, as shown in figure, has the drum diameter 250 mm. The angle of contact is 90° and the coefficient of friction between the drum and the lining is 0.35. The other dimensions are as follows: a = 200 mm, 1 = 400 mm and b = 100 mm. If the torque transmitted by the brake is 70 N-m, find the force F required to operate the brake. ock is Irum.
Problem 4 The maximum band interface pressure on the brake shown in the figure is 620 kPa. Use a 350 mm diameter drum, a band width of 25 mm, a coefficient of friction of 0.30, and an angle-of-wrap of 270. Find the band tensions and the torque capacity. Rotation P₂
The figure shows an internal rim-type brake having an inside rim diameter of 300 mm and a dimension R 5 125 mm. The shoes have a face width of 40 mm and are both actuated by a force of 2.2 kN. The drum rotates clockwise. The mean coefficient of friction is 0.28. a. Find the maximum pressure and indicate the shoe on which it occurs. b. Estimate the braking torque effected by each shoe, and find the total braking torque. c. Estimate the resulting hinge-pin reactions. 30°- 30°. R 120° 120° Pin Pin 30° 30° Figure 3: An internal rim-type brake
Problem 2 (Dimensions in mm.) The brake shown in the figure has a coefficient of friction of 0.30, a face width of 75 mm, and a limiting shoe lining pressure pV = 1.7 MPa x m/s. Find the limiting actuating force F and the torque capacity. IN 130° 125-125- 30° Rotation 30° 250R 20° 20° 75 75 130° 400. 100 300 300
Consider the arrangement of a simple band brake as shown in the figure. Determine the brake torque due to load applied at end A. Take the coefficient of friction as 0.22. 1.5 m 0.5 m B Answer Choices: a. 320 N-m b. 120 N-m c. 480 N-m d. 260 N-m 0.3 m 20% P = 250 N
A band brake is to absorb 5 Hp at 200 rpm. The maximum pressure of the lining and the drum is 120 psi. The angle of wrap is 3.6 radians, the width of the band is 3 inches and f = 0.15. Find the forces at the tight side. The diameter of the drum is at 8 inches. The correct answer is 2880 lbs. I just need a complete solution. Thank you!
| %or ,,l * M JO 9:YA docs.google.com/forms QI A double shoe brake, as shown in Fig. The diameter of the brake drum is 250 mm and the contact angle for each shoe is 90°. If the coefficient of friction for the brake lining and the drum is 0.35, find the spring force necessary to transmit a torque of 40 N-m. Also determine the width of the brake shoes, if the bearing pressure on the lining material is not to exceed 0.34 N/mm2 250 mm RN R 225 mm Ft Fulcrum 1 Add file
PROBLEMS Problem 1 (Dimensions in mm.) The block-type hand brake shown in the figure has a face width of 30 mm and a mean coefficient of friction of 0.25. For an estimated actuating force of 400 N, find the maximum pressure on the shoe and find the braking torque. 150 + 150R- 200- 90° -300- 45° 4 DIM in mm Rotation
A calliper brake is required for the front wheels of a sport's car with a braking capacity of 890,485 Nm for each brake. Preliminary design estimates have set the brake geometry as r=100 mm, ro=155 mm and 0=45°. A pad with a coefficient of friction of 0,45 has been selected. Determine: 4.1. the required actuating forces, 4.2. the average and maximum contact pressures.
An external long shoe drum brake is illustrated in Figure 2. The face width of the shoes is 60 mm and the maximum permissible lining pressure is 0.9 MPa. If the coefficient of friction is 0.30: 2.1 Determine the limiting actuating force. 2.2 Determine the torque capacity. Fa 250 mm- 300 mm- 45° 45 175 mm 200 mm Figure 2: Long-shoe brake
For the band brake shown below, the drum diameter is 16 inches, the coefficient of friction is 0.25, and the drum rotates at 300 rpm. If the maximum tensions in the band brake were 1000 Ib and 750 Ib. The band brake power is (in horsepower): 3 in- 10 in a 182 Ob 95 OG 13.6 Od. None of the above O e 25.4
The figure shows an internal rim-type brake having an inside rim diameter of 11in and a dimension R of 3.5 in. The shoes have a face width of 1.25 in. Find the braking torque and the maximum pressure for each shoe if the actuating force is 205 Ibf, the drum rotation is counterclockwise, and f=0.32. The maximum pressure on the right-hand shoe parp is [ 16.99] @ psi. The maximum pressure on the left-hand shoe pa| H is [100.813 | @ psi. The torque on the right-hand shoe Tgis [ .056 | @ kipin. The torque on the left-hand shoe T is [ .332| @ kipin. Total braking torque Tiotal s [-3887] @ Kip-in.