3)The accompanying tabulation gives elevations of points over the area 20m by 20m city lot.The elevations were obtained by the checkerboard method using 10-m squares. Requirements: a)Plot the contours using a horizontal scale of 6cm=10m and a contour interval of 1 meter. b)Use short-sized bond paper.All corner designations and corresponding elevations must be indicated, including all vertical and horizontal lines. c)Indicate the following Index contours:880,885,890 & 895.The thickness of the index contours must be drawn about twice the thickness of intermediate contours. d)Show solutions in interpolations. EE A 878.80m 882.50m 883.50m B 883.20m 885.90m 893.70m C 882.80m 888.60m 891.80m

3)The accompanying tabulation gives elevations of points over the area 20m by 20m city lot.The elevations were obtained by the checkerboard method using 10-m squares. Requirements: a)Plot the contours using a horizontal scale of 6cm=10m and a contour interval of 1 meter. b)Use short-sized bond paper.All corner designations and corresponding elevations must be indicated, including all vertical and horizontal lines. c)Indicate the following Index contours:880,885,890 & 895.The thickness of the index contours must be drawn about twice the thickness of intermediate contours. d)Show solutions in interpolations. EE A 878.80m 882.50m 883.50m B 883.20m 885.90m 893.70m C 882.80m 888.60m 891.80m

Architectural Drafting and Design (MindTap Course List)

7th Edition

ISBN:9781285165738

Author:Alan Jefferis, David A. Madsen, David P. Madsen

Publisher:Alan Jefferis, David A. Madsen, David P. Madsen

Chapter15: Site Plan Layout

Section: Chapter Questions

Problem 15.25Q

See similar textbooks

Similar questions

3)The accompanying tabulation gives elevations of points over the area 20m by 20m city lot.The elevations were obtained by the checkerboard method using 10-m squares. Requirements: a)Plot the contours using a horizontal scale of 6cm=10m and a contour interval of 1 meter. b)Use short-sized bond paper.All corner desiqnations and corresponding elevations must be indicated,including all vertical and horizontal lines. c)lndicate the following Index contours:880,885,890 & 895.The thickness of the index contours must be drawn about twice the thickness of intermediate contours. d)Show solutions in interpolations. 2 A 882.80m 888.60m 891.80m B 882.50m 890.40m 892.60m C883.20m 888.50m 892.80m GOD BLESS!
The accompanying tabulation gives elevations of points over the area 30m by 30mcity lot. The following elevations were obtained: Determine the following:a)Plot the contours using a scale of 1cm=10m witha contour interval of every 10meters.All corner designations and corresponding elevations mustbe indicated,including all vertical and horizontal lines.Indicate the followingIndex contours:860,890. The thickness of the index contours must be drawn about twice the thickness of intermediate contours.b)Compute for the horizontal distances of each contourfoundbetween two points. Show your complete solution.
Please draw it on grid sheet with proper dimensions
Draw a grid 6 in wide by 7 in long with 1-in intersections, and place the given elevations at the intersections in the same arrangement as follows a. Draw the 5-m contours 22 17 28 40 47 52 57 27 24 22 33 41 46 51 35 32 28 27 34 42 49 45 41 37 31 37 43 49 50 52 48 40 36 42 50 45 46 46 42 44 49 52 34 30 38 45 50 55 60 23 34 45 50 55 60 65
Determine the centroid coordinates, Xc and Yc, use table attached.
compute the area using trapezoidal rule and provide table base on the sketch provided
Please solve the Traverse, and fill out the chart below. Include Sketch Markings if possible.
The following tabulation (see image) gives elevations of points over the area of a 60-by-100 ft city lot. The elevations were obtained by the checkerboard method, using 20-ft squares. Point A-1 is in the northwest corner of the lot, and point F-1 is at the southwest corner. Plot the contours, using preferred scale and a contour interval at 2 feet.
Subject :Surveying Please show sketch and give me complete detailed solution.
4. Complete the accompanying set of profile notes and perform the arithmetic check. Provide a sketch of this project's profile view. (You can use excel to sketch) Station BS (ft) HI (ft) IS (ft) FS (ft) BM1 0+00 1+00 2+00 3+00 3+35 4+00 TP1 5+00 5+20 5+30 6+00 BM2 4.58 4.87 2.59 3.79 4.82 4.98 5.05 7.30 4.60 4.78 4.85 4.89 11.21 10.58 Elevation (ft) 427.06
A line AB is 40 mm long.Endpoints A & B are 20 mm in-front of Vertical Plane.Endpoints A is 15 mm above Horizontal Plane at 45 degrees.Draw projections & trace of the line.
Define integer ambiguity.