4 in.200 kip3 ft- The column is constructed from high-strength concrete and eight A992 steel reinforcing rods.If the column is subjected to an axial force of 200 kip, determine the average normal stress in theconcrete and in each rod. Each rod has a diameter of 1 in- change the applied force of 200 kip to 185.7 kip- change original diameter of each steel rod of 1 in to 1.35 in

Answered: Image /qna-images/answer/0da8f95f-805f-419c-aa6f-c4bddef68897.jpg

4 in. 200 kip 3 ft The column is constructed from high-strength concrete and eight A992 steel reinforcing the column is subjected to an axial force of 200 kip, determine the average normal stress ncrete and in each rod. Each rod has a diameter of 1 in change the applied force of 200 kip to 185.7 kip change original diameter of each steel rod of 1 in to 1.35 in

4 in. 200 kip 3 ft The column is constructed from high-strength concrete and eight A992 steel reinforcing the column is subjected to an axial force of 200 kip, determine the average normal stress ncrete and in each rod. Each rod has a diameter of 1 in change the applied force of 200 kip to 185.7 kip change original diameter of each steel rod of 1 in to 1.35 in

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The concrete post is reinforced axially with four symmetrically placed steel bars, each of cross-sectional area 900 mm2. Compute the stress in each material when the 1000-kN axial load is applied. The moduli of elasticity are 200 GPa for steel and 14 GPa for concrete. Compatibiltiy Equation (20 points), o co (20 points), Ost (20 points). |1000 kN Bearing plate 1 a Steel Concrete 300 mm 300 mm Section a-a
2.40 Three steel rods (E = 29 X 105 psi) support an 8.5-kip load P. Each of the rods AB and CD has a 0.32-in² cross-sectional area and rod EF has a 1-in² cross-sectional area. Neglecting the defor- mation of bar BED, determine (a) the change in length of rod EF, (b) the stress in each rod.
A square hollow steel structure with a wall thickness of t1 = 10 mm is pin linked to two gusset plates with a thickness of t2 = 12 mm, which are welded to a base plate with a thickness of 12 mm and secured to a concrete base with 4-16 mm diameter anchor bolts. The pin has a diameter of 16 mm. P = 48 kN compressive load, 30 deg. P= 48 kN Stnt gusset plate fy=12 mm 0=30 10 m 12 mm 16 mm ø anchor bolt 4-16 mm p 1. Determine the bearing stress in MPa between the struct and the pin. 2. Calculate the pin's shear stress in MPa. 3. Determine the anchor's shear stress in MPa.
Determine the largest permissible value of P for the beam and loading shown, knowing that the allowable normal stress is +80 MPa in tension and -115 MPa in compression. 0.2 m B 0.4 m. 0.2 m D 12 mm H 96 mm The largest permissible value of P is 48 mm 12 mm kN.
Compute the stress at each segment of the pipe.
60 mm 150 mm 60 mm 300 mm 600 III 60 mm 150 m
Time left 0:16:22 (CLO 1, 2)Determine the stress in the Aluminum rod (Psi) after the load 142 (kips) is applied. The light rigid bar ABCD is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free. Steel L = 3 ft A = 0.5 in? E = 29 x 10° psi 4 ft - Aluminum P. 2 ft 2 ft-> L= 4 ft A = 0.75 in? E = 10 x 10° psi %3D
A round vertical steel column 500 mm in outside diameter and a wall thickness of 10mm is reinforced with four reinforcing bars 3 cm in diameter. It is filled with concrete and supports a load of 800 kN. Bearing plates are placed on top and bottom of the 1.5 m high column to assure equal deformation of the steel and concrete. Find the stress in each material and the change in height of the column. [Ec = 14 000 MPa, Es=200 GPa assume both column and steel re-bar are same type of steel]
A simply supported concrete beam 6m long is reinforce with four-28 mm diamgram tension bars. The beam has a width of 300mm and over all depth of 400.the steel covering to the centroid of the renforcement is 70 mm fc=30mpa and fy 418mpa A .draw a stress diagram B.compute for the ultimate capacity of the beam
four cables are used to lift a precast concrete slab with dimensions 3m x 3m and 76mm thick. The cables are attached to a hook above the center point of the slab. What is the force in each of the cables? (kN) Determine the normal stress in each of the cables? (MPa)
Determine the largest weight “W” that can be supported by the two wires AB and AC. The working stresses are 100MPa for AB and 150MPa for AC. The cross sectional area of AB and AC are 400mm2 and 200mm2 Compute “W” due to the stress capacity of AB Compute “W” due to the stress capacity of AC. Determine the safest value of “W”.
All unit are in MPa. Compute maximum principal stress 5 10 10