5) A collar, C, has a mass, mc, is allowed to freely slide along rod AD and is attached to spring BC. The spring has an undeformed length of 10 cm and spring constant, k = 5000 N/m. %3D mc = 5.0 kg LAB = 10.0 cm LAD = 1.0N m2 %3D The system initially has a rotation rate of w = 15.0 rad/s, distance to collar LAC = 30.0 cm, and the collar has zero velocity with respect to the rod AD. a. What is the rotation rate of the assembly as the collar passes through a point 5.0 cm from point A (ie. LẠC = 5.0 cm)? b. What is the corresponding velocity of the collar relative to the rod.

5) A collar, C, has a mass, mc, is allowed to freely slide along rod AD and is attached to spring BC. The spring has an undeformed length of 10 cm and spring constant, k = 5000 N/m. %3D mc = 5.0 kg LAB = 10.0 cm LAD = 1.0N m2 %3D The system initially has a rotation rate of w = 15.0 rad/s, distance to collar LAC = 30.0 cm, and the collar has zero velocity with respect to the rod AD. a. What is the rotation rate of the assembly as the collar passes through a point 5.0 cm from point A (ie. LẠC = 5.0 cm)? b. What is the corresponding velocity of the collar relative to the rod.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider the dynamic system shown below. Rod Pulley Rc Rod Pulley RA = 10 cm PIB 1A The following parameters are given for the system: m₂ = 1 kg RA mg mc 2 kg RB Rc 20 cm m₂ = 3 kg R₂ = 30 cm k = 1200 N/m Note that pulleys A and B are constrained to move together and pulleys C and D are constrained to move together. Useful note... a. Obtain the characteristic equation(s) for this system. b. The applied force is removed. Then, pulley A/B is turned 2 degrees and released from rest. Find the system response.
Problem Solving: )An object falls from rest in a medium offering a resistonce. The velocity of the object hefore the ohject reaches the ground is given by the differential egua- tion dv/t + V% = 32, t/sec. uhat is the veloaty of the okject one second after it falls ?
Conservative mechanical system consists of two homogeneous disks of mass. mi and ma The disks have some radius R. The disks Con roll on and their centres dae a horizontal surface without slipping attached to a spring of elastic constant k and rest length I. The in horizontal direction disk centres only move (the disk always touch surface). 1- A ma mmmmmmmmml / / / / / / / / / / / / / mi (v) State number of degress of freedom? ii).write longrengion and Euler-long range equations of system? (L). Find stable equlibrium position (S) of system? iv). State conserved quantity (or quantities) of the system. For each conserved quantity, state the Noether symetry responsible for its Conservation? V). Find normal modes of small osscilatione about stable equlibrium position (s). calculate Corresponding frequencies? rદ્ર લવ
(b) A system of mass rotation rod has been run at = 40 rad/s as shown in Figure Q1. The system has the following data, (i) (ii) Mass Mass A Mass B Mass C Weigh 1.2 kg 1.8 kg Mc Radius 1.135 m 0.822 m Re Angle 113.4° 48.8° вс Find counterweight mass-radius product and its angular location needed to balance the system. Distinguish the relationship between mass, radius and angle for counterweight mass system.
\ It is known that the belt drive power P = 7.5K@, driving wheel diameter d, =100mm, rotating speed n, = 1200rpmand tight side tension F, are twice that of loose side tension. F, . Try to find the value of F,and F, ?
Lo k Jasen Lo 2k 3m. 1 B F Problem 3 The collar of mass can slide on the horizontal rail. The collar is supported by two linear springs of stiffness k and 2k; they have identical free length Lo. The homo- geneous bar of mass 3m and length I is attached to the collar by joint A. The bar is subjected to a horizontal, time-dependent force F(t). Derive equations of motion for the mechanical system.
Sample Probl Newton's 2nd law, rotation Figure 10-18a shows a uniform disk, with mass M = 2.5 kg and radius R320 cm, mounted on A block with mass m = 1.2 kg hangs from a massless cord that is wrapped around the rim of the disk. Find the acceleration of the falling block, the angular acceleration of the disk, and the tension in the cord. The cord does not slip, and there is no fric- tion at the axle. a fixed horizontal axle.
igure 2. Assume that the rod is massless, perfectly rigid, and pivoted at point P. When the rod is perfectly horizontal, the angle 0 = 0, the displacement y 0, and the springs are in neither tension nor compression. Gravity acts on the system (e.g. on mass M). We assume that y is a small displacement. A mass M is attached at the end of the rod. DE only 225 Your tasks: X k 0 3k a F a M y A Derive an equation of motion for the system in terms of the angular displacement 0, and its derivatives (you should not have y or its derivatives in this equation.) B Derive an equation of motion for the system in terms of the displacement y, and its derivatives (you should not have or its derivatives in this equation. C Assuming there is no external actuator force F acting on the system, write down the total energy H of the system in terms of 0,0 and element constants. Derive an expression for the time derivative H of the total energy. D Transform the equation from part B, which is in y, to another…
Dtes 6) Take a look at the picture below. Initially the system is at rest. The spring is activated and sends the mass moving with tangential speed "v" and the disk rotating with angular velocity "w". Find expressions for these parameters in terms of the variables given. Final I nitind At Rest Dişk Rolutes Sprivag: compressx a mass と szring Cons & ingetid velocty muss Rotafiond ふnertiu ofDk
Please answer the following question A cigarettes dispenser requires a south African five-rand (R5) coin with a mass of 9.5 g to dispense one cigarette with a mass of 0.2 g. The design of such a cigarette dispenser is based on a helical spring, of negligible mass, which is found to extend 0.1 mm under a mass of 0.2 g. The spring can support a total mass of a coin. As the customer place money on the dispenser, the spring and coin system displace vertically through 4 mm and release. 1.1. Provide a schematic representation of the mass and spring system. 1.2. Calculate the frequency of natural vibration of the dispenser. 1.3. Determine the velocity of the coin when it is 2 mm below its resting position.
Consider the two-degrees-of-freedom mass-spring system below. Assume m₁ = 30 kg, m2 = 35 kg. If the second natural frequency of the system is 100 rad/s, the value of stiffness k is www. k₁=k k₂ = k k3= k 174.41 kN/m 107.38 kN/m 140.93 kN/m 39.24 kN/m 73.62 kN/m Next 000 00 Previous 4 x₁ (t) x₂ (t) m₁ m₂. mm
9:48 *41| 26% O 1 of 1 Aunifim dik of radius rand mass can roll without slipping on a platform which rotates about the hinpe joint Ot a rate a (met constant), ie, the platform makes an angle 0- aat with the horizontal 1. How many degrees of freedom is this system? What peneralized coordinates will you use? 2. What is the kinetic energy of the system? 3. What is the potential energy of the system? 4. What are the differential equations of motion for this system? of For the toolbar, press ALT+F10 (PC) or ALT+FN+F10 (Mac). BIUS Paragraph In Arial 14px 20210420_204733.jpg| 1.3 MB