5.15 Carbon steel (AISI 1010) shafts of 0.1-m diameter are heat treated in a gas-fired furnace whose gases are at 1200 K and provide a convection coefficient of 100 W/m² K. If the shafts enter the furnace at 300 K, how long must they remain in the furnace to achieve a centerline temperature of 800 K?

5.15 Carbon steel (AISI 1010) shafts of 0.1-m diameter are heat treated in a gas-fired furnace whose gases are at 1200 K and provide a convection coefficient of 100 W/m² K. If the shafts enter the furnace at 300 K, how long must they remain in the furnace to achieve a centerline temperature of 800 K?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.36P

See similar textbooks

Similar questions

Question : Studies show that the major energy consumption in Fijian villages is wood which is used for cooking over open fires. Typical consumption of wood is 1 kg person–1day–1. (a) Estimate the heat energy required to boil a 2-liter pot full of water. Assuming this to be the cooking requirement of each person, compare this with the heat content of the wood, and thus estimate the thermal efficiency of the open fire. (b) How much timber has to be felled each year to cook for a village of 200 people?Assuming systematic replanting, what area of crop must the village therefore set aside for fuel use if it is not to make a net deforestation? Hint: refer to Table 10.4. (c) Comment on the realism of the assumptions made, and revise your estimates accordingly. Answer: (a) mcDT ≈ 0.6 MJ (heat losses from pot imply actual requirement is higher). h ≈ 3%. (b) 70 tonnes; 7 ha.
20. The two plates of Problem 11 made of the same material and having constantk are exposed on one side to hot water at Tw and hw and on the other to cold air atTa and ha. Find a) the equation for temperature profile in these plates and b) temperaturesat x = 0 and at x = L if hw = ha = h. [Ans.: a) T1(x) = c1x + c2 where, c1 = hw(Ta – Tw)/c3 and c2 – Ta = – hw(haL +k)(Ta – Tw)/(hac3) where c3 = (k + hwL + hwk/ha)].
A 2.54-cm. steel bolt is used to clamp two aluminum (2014-T6, HT aged) plates together as shown by Fig. Problem 5. The aluminum plates have a total thickness of 08 cm. and an equivalent diameter of 5.08 cm. The bolt is heated to a temperature of 93.33 oC, the inserted in the aluminum plates, which are at 26.7 oC, and tightened so as to have a tensile tightening stress of 207 MPa in the unthreaded shank while steel at 93.33 oC. What is the tensile stress in the bolt after assembly has cooled to 26.7 oC? The deformations are elastic.
In general, it is helpful to think of a thermally lumped object as being “tied down” to somereference temperature through a general thermal resistance. In the simplest case this is asingle thermal resistance (e.g., just convection), but there are cases for which this thermalresistance is composed of more than one heat transfer mechanism. Consider the quenchingof a solid, alloy 2024-T6 aluminum rod that has been coated with a thin insulating material.If the insulating material is thin enough that its thermal energy storage capacity can beignored, the effective resistance between the rod and the quenching fluid consists of boththe conduction through the insulating material and the convection to the fluid.a) The simplest version of the Biot number is Bi = ℎ??? . When there are multipleexternal resistances between the lumped object at the surroundings the Biot numbergeneralizes to Bi = ???? , where ? is the overall heat transfer coefficient between thelumped object and the surroundings.The…
Recent studies show that the major energy consumption in Fijian villages is wood which is used for cooking on open fires. Typical consumption of wood is 1 kg/person/day. (a) Estimate the heat energy required to boil a 2 litre pot full of water. Assuming this to be the cooking requirement of each person, compare this with the heat content of the wood, and thus estimate the thermal efficiency of the open fire. (b) How much timber has to be felled each year to cook for a village of 200 people ? Assuming systematic replanting, what area of crop must the village therefore set aside for fuel use if it is not to make a net deforestation ?
A 12-by-12 inches ingot iron casting 60-in high is stripped from its moldwhile its temperature is 1740 °F. If it stands on end on the floor of a largefoundry having wall, floor, and roof temperatures of 80°F, what is the rate ofradiant-heat exchange between the casting and the roof wall, and floorsurfaces?
A composite wall is formed of a 2.5 cm copper plate, a 3.2 mm layer of asbestos,and a 5 cm layer of fiberglass. The wall is subjected to an overall temperaturedifference of 560oC. Calculate the heat flux through the composite structure.
Determine the heat flux through the composite walls as shown in Figure. The frontal area (normal to heat flow) for the layers of Fir brick and Brick is 1 sq.m. The frontal area for Asbestos and Earth layers are equal and the summation of the frontal areas of them is 1 sq.m. as shown required to answer. OPTIONS: 1.Heat flux is around 487.3 Watt 2.Heat flux is around 742.7 Watt 3.Heat flux is around 305.4 Watt 4.None
Two inches of urethane foam will reduce heat loss close to 1000% when applied to a 2-inch diameter uninsulated steel pipe. Assume the pipe wall thickness is 0.25-inches, the pipe interior convective heat loss (hi) is 500 BTU/hr-ft2-oF, and the pipe outside convective heat loss ho 20 BTU/hr-ft2-oF, k steel is 25 BTU/hr-ft-oF, and k insulaton is 0.023 BTU/hr-ft-oF. (hint - calculate heat loss with and without insulation.
PROBLEM: VB-17 BOOK: ENGINEERING THERMOFLUIDS, M. MASSOUD
PROBLEM (4) What does it mean for an object to have a negative heat capacity?
Question 1 A composite component is comprised of a tube and a concentric rod running inside it, both with a length of 1.5 meters. The tube is made of copper and has inner and outer diameters of 60 mm and 100 mm, respecti vely, a coefficient of thermal expansion and elastic modulus of 17 x10-6C and 117 GPa, respectively. The rod is made of aluminium with a diameter, coefficient of thermal expansion and elastic modulus of 50 mm, 23 x10-6C and 80 GPa, respectively. If the composite is exposed to a temperature rise of 120°C, determine: The sense and magnitude of the stresses induced in the composite if it is not restrained. 1.1 1.2 The sense and magnitude of the stresses induced in the composite ifit is partially restrained with an allowed free expansion of 0.3 mm.