54. A drawing is given and below the drawing are sketches of two produced parts with surface variationsexaggerated. Assume the holes are produced exactly on the true positions defined by the drawing. Drawand label datum planes that are needed for the measurements. Indicate any orientation requirementbetween the datums. Show dimensions on the produced parts to indicate where the location dimensionsare measured on each of the given parts.-2х ф.312+.006-.001+0.031 O A BC.500.312.900

The datum planes that are required for the measurement with respect to the holes can be taken as…

Answered: 54. A drawing is given and below the…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Draft and annotate the 2D sketch of cover using AutoCAD and mention all the dimensions. Colour the hatched lines which are inside the curve 8R 6 holes 8 Dia 62 Dia 18 R 3 holes 20 Dia 110 Cover 40 Dia 100 R
Write all the commands steps of the AutoCAD software to reach the drawing of the figure below all dimensions in mm -80- -70 -50 040- -Ø120 -260 10. 120- 60 40 293.2- -D120- SECTION A-A Your answer 120- -090- -2X45° R30 93.2- 10 -2X45 090 120
The below figure shows two views of a bolster block. Draw, using 1 st angle projection and a suitable scale, the following views: (a) the given front elevation; (b) a sectional end elevation taken on the cut-ting plane A-A; (c) the given plan; (d) an isometric view of the block. Show all hidden details. Print title, scale and show six leading dimensions Note : use creo parametric to solve the answer
Question 3 Make an Isometric Drawing of the support bracket shown in Figure 4. Take the dimension 'H' as 35 mm. As per standard instruction for pictorial views in ENG1100, no dimensioning is required. Orientate the drawing so View A' of Figure 4 is in the direction of the shaded face of the representative isometric view of a cube shown in Figure 3 with the top of the 'View A' orientated towards TOP' as shown in Figure 3. Top Figure 3 140 22 DRILL 96 - 22 22R 16 41 198 40 - 5/ 51- 16- 19R 16 DRILL-3HOLES 51- View A Figure 4: Support Bracket (Source: Boundy AW, Engineering drawing, 8th edn, McGraw Hill, dimensions altered)
Draw the three projections of the body in Figure 1- using AutoCAD 1-Do not write the dimensions on the drawing 2- Draw with the same measurements as shown 3 -Show graphics properties At least properties are required for the circle and arc R10 R20 40 35 55 -1- JSI 9.
Some necessary dimensions are missing from the following 3-view drawing. Describe 2 of the dimensions that are missing. 7.00 1.00 5.00 2.00- 0 1.00 R1.00 I 00 2.00 00'L 00 00
Draw front and right-side views of the following object with a completed dimensions. Draw in scale 1:1 on A4 sheet. (Problem is taken from "Graphics for Engineers' by Earle) 78 What can we learm from the drawlng ? 1. The dimension note M10x1.5 means that the hole is a threaded hole. R16 O 16, 2 Holes The letter 'M' means that the threads are made by following a metric thread system. The number "10" Is the major dlameter of the hole and the number 1.5 is the pitch of a thread. However, for coarse threads, it is a common practice to omit specifying the pitches. For example, a note M10 means the pitches of the thread is 1.5 mm. In this book, the pitch is specified in order to facilitate drafting. 2. Drawing symbol of a threaded hole is shown below. - Thin Ine (4H pench The ends of this arc does not meet together but approximately 90 degs, apart. Object Ihe (2i pencil .major dlameter pich2 M10x1 5 3. The circular projection surface at a threaded hole that is raised from a cylinder is…
Sketch the 2D figure of cover using AutoCAD and mention all the dimensions, colour the hatched lines if there any. 80 Dia 8 42 106 22 42 16 24 R 16 R 80 Cover
When no geometric tolerance is specified, the size tolerance controls the well as the size. O form orientation O profile O position as
do not reject . let other do the solution if u dont know. skip 86 30 ugh hole 16 6 20 Dig 28 18 Dia for the above isometric view , sketch the orthographic view in first angle proiection using catia v5 software. 36
CIMS Identify the drilling operation in which the flat bottom drill bit is used to enlarge the existing hole. Counter sinking operation en O Gun drilling O Core drilling operation O Counter boring operation In sand casting process good dimensional accuracy can be obtained compared to die casting process. Select one: of O True O False tion Next page 99- pe here to search IO 1- $ 3. 6. & 7 V E 00 立

Draft and annotate the 2D sketch of housing using AutoCAD and mention all the dimensions. Colour the hatched lines (blue) which are inside the curve 56 27R 83R 30R 10R 20 22 10R 27R 3 holes 28 Dia 60 Housing 82

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS