6. A pump draws water from a sump through a vertical 6" pipe. The pump has a horizontal discharge pipe 4" in diameter that is 10.6 ft above the water level in the sump. While pumping 1.25 cfs, gages near the pump at entrance and discharge read -4.6 psi and +25.6 psi, respectively. The discharge gage is 3.0 ft above the suction gage. Compute the horsepower output of the pump and the head lost in the 6" suction pipe.

6. A pump draws water from a sump through a vertical 6" pipe. The pump has a horizontal discharge pipe 4" in diameter that is 10.6 ft above the water level in the sump. While pumping 1.25 cfs, gages near the pump at entrance and discharge read -4.6 psi and +25.6 psi, respectively. The discharge gage is 3.0 ft above the suction gage. Compute the horsepower output of the pump and the head lost in the 6" suction pipe.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Include a free body diagram. pump draws water from a sump through a vertical 6′′ pipe. The pump has a horizontal discharge pipe 4′′ in diameter that is 10.6 ft above the water level in the sump. While pumping 1.25 cfs, gages near the pump at entrance and discharge read —4.6 psi and +25.6 psi, respectively. The discharge gage is 3.0 ft above the suction gage. Compute the horsepower output of the pump and the head lost in the 6′′ suction pipe. (ANSWER: 10.7 Hp, 2.4 ft)
Q No. 5: The diameter of side of a pump is 6 inches and that of the intake pipe is 8 inches. The pressure gauge at discharge reads 30 psi and vacuumed gauge at intake reads 10 inches of Hg. If Q=3cfs of water and the brake horsepower is 35. Find the efficiency of the pump. There are no losses. Note : Please Solve as Per Question's Statement. Need a Neat and Clear Solution.See Attached Picture For Detail .
A 2ft 14 4 ft Determine the rate of discharge and gage pressure at point A даде
8. A pumped fluid distribution system is being designed to deliver 400 gal/min of water to a cooling system in a power generation plant. Use the figure below to make an initial selection of Schedule 40 pipe sizes for the suction and discharge lines for the system. Also, solve for the actual average velocity of flow for each pipe. DN (mm) NPS (in) 250 200- 150 - 6 125- Suction lines 100 - 4 3. 65 2 50E 2 Discharge lines 40 - 32 - 25 E 15 15 20 30 40 60 200 400 600 S00 2000 4000 6000 S00 80 100 10 Volume Flow Rate, Qallmin) 8 10 15 20 25 30 40 +++++ +++ 60 80 100 150 200 300 400 500600 800 1000 1200 2000 +++++ +++++ Volame Flow Rate, Q (mVh)
● Determine the head needed to be covered if the pump has an 8 inches normal size suction and 6 inches nominal size discharge if it handles 150 gpm of water at 150. The suction line gage shows 4” Hg vacuum and the discharge gage shows 26 psi. The discharge gage is located 2 feet above the center of the discharge pipe line and the pump inlet and discharge lines are at the same elevation.
8. A pumped fluid distribution system is being designed to deliver 400 gal/min of water to a cooling system in a power generation plant. Use the figure below to make an initial selection of Schedule 40 pipe sizes for the suction and discharge lines for the system. Also, solve for the actual average velocity of flow for each pipe. DN (mm) NPS (in) 250 200 150 - 125 - Suction lines 100 - 90 - 3 65 - 2 50 Discharge lines 40 32E 25 E 15 20 200 400 600 800 1000 2000 4000 6000 8000 10000 10 100 Volume Flow Rate, Q (gal/min) 6 8 10 ++++ 15 20 25 30 40 +++++++++ ++++++++++++ 60 80 100 150 200 300 400 500600 800 1000 1200 2000 Volume Flow Rate, Q (m/h)
URGENT Please answer this problem in 30minutes. I need correct answers with complete and step by step solution. Box the final answers. Do not shortcut your solution. I will give an upvote if it satisfies. Thank you! If the velocity of water is 8 m/s and the pressure is 140 kPa on the discharge side of a pump. a. What is the head of the pump if the velocity is 4 m/s and the pressure is 90 kPa on the suction side of the pump? b. How much power is required to drive it if the diameter of the suction side is 600mm? c. If the pump is rated at 120hp, what is the efficiency of the pump neglecting energy losses in the system?
8.) A liquid having a sp.gr. of 20 is flowing in a 50 mm diameter pipe. The total head at a given point was found to be 17.5 Joule per Newton. The elevation of the pipe above the datum is 3 m and the pressure in the pipe is 65.6 kPa. Compute the velocity of flow and the horsepower in the stream at that point. Subject: Fluid Mechanic Lesson: Relative Equilibrium of Liquids Fundamentals of Fluid Flow
Figure below shows a siphon that is used to draw water from a tank. The siphon tube has an inside area of . The exit nozzle at point F has an inside area of . The distances are , , and , respectively. Find the pressure at point D_______ A. 5.74 kPa (gage) B. -5.74 kPa (gage) C. 5.74 kPa (absolute) D. -5.74 kPa (absolute)
QUESTION 4 The figure below shows a fluid flow system that is designed to pump water at 20 °C from a lower vented reservoir to an elevated vented tank. Note that the drawing is not to scale as the dimensions of the reservoirs are very large relative to those of the piping system. The suction line entering the pump is specified as 20 m of 3½" schedule 40 commercial steel pipe; the discharge line from the pump is 180 m of 2%" schedule 40 commercial steel pipe. 15 m 3 m 31/2-in Schedule 40 steel pipe Fully open gate valve 21/2-in Schedule 40 steel pipe Flanged regular 90⁰ elbows Pump Flow Swing-type check valve valve Butterfly (K butterfly = 0.8) a. Starting from the Bernoulli equation (in 'head' form) for the situation where the liquid levels in the two reservoirs are reference points 1 and 2, derive the correct equation for pump head Hpump (m) in terms of volumetric flow rate Q (m³/s) and other process variables (e.g. z, f, L, D, K). b. Using Excel (or another suitable program), create…
6. A pump is located 4.5 m to one side of, and 3.5 m above a reservoir. The pump is designed for a flow rate of 6 L s'. For satisfactory operation, the static pressure at the pump inlet must not be lower than -6 m of the water gage. Determine the smallest standard commercial steel pipe that will give the required performance. pump 4.5 m. 1.8 19=d 3.5 m 7. water 90° elbow
8. A horizontal pipe 2.0 mm in radius at one end gradually increases in size so that it is 5.0 mm in radius at the other end. The pipe is 4.0 m long. Water is pumped into a small end of the pipe at the speed of 8.0 m/s and the pressure of 2.0 bar. a. Find the speed and the pressure of the water larger end of the pipe. b. The pipe is turned so as to be vertical with the small end underneath, so the water flows upward. Find the speed and the pressure of the water at the large end of the pipe now. c. How many liters of water flows in the pipe in (a) in 1 hour?