6. An engine part weighs 62 61 Lb When this part is immersed in water, it displaces a total volume of 8 77 L What is the density of this material? Round off your final answer to 3 snignificant figures Show all your calculations below

6. An engine part weighs 62 61 Lb When this part is immersed in water, it displaces a total volume of 8 77 L What is the density of this material? Round off your final answer to 3 snignificant figures Show all your calculations below

Inquiry into Physics

8th Edition

ISBN:9781337515863

Author:Ostdiek

Publisher:Ostdiek

Chapter4: Physics Of Matter

Section: Chapter Questions

Problem 8P: A small statue is recovered in an archaeological dig. Its weight is measured to be 96 lb, and its...

See similar textbooks

Similar questions

(a) A rectangular gasoline tank can hold 50.0 kg of gasoline when full. What is the depth of the tank if it is 0.500-m wide by 0.900-m long? (b) Discuss whether this gas tank has a reasonable volume for a passenger car.
What fraction of an iceberg floating in the ocean is above sea level? Assume the density of the iceberg is 917 kg/m3.
An object (s=0.65) floats in a liquid (s=0.80). 1. Determine the percentage of the volume above the liquid surface to the total volume of the object. 2. Calculate the weight of the object if the volume above the liquid surface is 0.015 m3. Note: Answer the situations with complete solutions. Write your final answer in two decimal places. Please use the correct unit and box the final answer Thank you
As shown in the figure below, a cylinder fitted with a piston is filled with 700 lb of saturated liquid ammonia at 45°F. The piston weighs 1 ton and has a diameter of 2.5 ft. What is the volume occupied by the ammonia, in ft³? Part A Patm = 1 atm Piston Ignoring friction, determine the force required, in lbf, by mechanical attachments, such as stops, to hold the piston in place. V= i Ammonia Saturated liquid What is the volume occupied by the ammonia, in ft³? ft3 - Weight = 1 ton D=2.5 ft
5. a) Describe how the mass of a cube of metal changes with the length of the cube. b) Describe how the surface area to volume ratio changes with the length of the cube. Application Questions 6. A student makes the following statement. "If I double the amount of metal I have, the density will double." Is the student correct? Explain 7. If a balloon filled with air is put into a jar with a vacuum the balloon will expand. Assume that no air leaks out of the balloon. a) How does the volume occupied by the air change? Explain. b) What happens to the mass of the air? Explain. c) What happens to the density? Explain.
ule wate 11. Using the graduated cylinders below find the volume of the object. Calculate the density if the mass is 78.42 g. 12. L 100 100 90 80 70
A group of students wish to determine, experimentally, the bulk density of an unknown material. To determine this amount, the students measured the diameter, height, and mass of various cylinders. These values appear in the table below. Determine: c) The volumetric density of the material from which the cylinders are made. d) Determine the volume of a sphere that has a mass of 800g and that is made of the same material as the cylinders used in the table above. e) Determine the radius of the sphere.
Can you help me draw a diagram for each number? thank you 1.)The velocity of the water at the entrance and exit of a pipe are 10 m/s and 3 m/s,respectively. The volume of water flowing inside the tube is 18000 m 3 . What isthe kinetic energy of the water measured at the exit of the pipe? 2. If the exit of the pipe in problem 1 is located at the ground level, what is theelevation of the pipe inlet if all the potential energy is converted to the kineticenergy in problem 1? 3. What is the total thermodynamic heat released by heating 2 kg of solid ice at 0 0 C(2093 J/kg-K) to 100 0 C without steam formation?
Question 1 a) A container of volume 2000 cm3 is completely filled by carefully pouring 1.7 kg of powder into it. The powder has a Carr’s Index of 25% and particle density of 1.40 kgm3. What is the bulk density of the powder? B)Calculate the bulk density of the powder in the container in part a) if it is tapped repeatedly. C) Calculate the voidage of the powder before and after tapping
A cube 5.5 cmcm on each side is made of a metal alloy. After you drill a cylindrical hole 3.0 cmcm in diameter all the way through and perpendicular to one face, you find that the cube weighs 6.60 NN. 1. What is the density of this metal? Express your answer with the appropriate units. 2. What did the cube weigh before you drilled the hole in it? Express your answer with the appropriate units.
The figure below shows the essential parts of a hydraulic brake system. The area of the piston in the master cylinder is 1.8 cm2, and that of the piston in the brake cylinder is 6.4 cm². The coefficient of friction between shoe and wheel drum is 0.50. If the wheel has a radius of 39 cm, determine the frictional torque about the axle when a force of 32,N is exerted on the brake pedal. N-m Wheel drum. Shoe- Pedal Master Brake cylinder cylinder
Midterm Exam kg it was 1. When a block of an unknown material is placed in a fluid with a density of 1253 ma observed that 43% of its volume is submerged in the fluid. a. What is the density of the block? b. Find the Specific Gravity of the block of wood. 2. Find the percentage of volume submerged of an object if its specific weight is 9638- N and is lbm submerged in a fluid with a density of 2243 m². (2.22lbm = 1kg) 3. An object is placed on water, and it is observed that it floats and 72% of it is above the water's surface. Find the object's specific volume. 4. An 8kg plastic block with a specific volume of 5.69x10-4 "m - is fully submerged in water while kg attached to a rope. What is the tension force on the rope? lbm 5. An object with a volume of 0.04m³ is fully submerged in a fluid with a density of 925 while ft3 attached to a rope. Find the object's mass if the tension force on the rope is 346N. (2.22lbm = 1kg; 3.29ft = 1m)