6. In the steel structure shown, a 6mm diameter pin is used at C and 10mm diameter pins are used at B and D. The ultimate shearing stress is 150 MPa at all connections, and the ultimate normal stress is 400 MPa in link BD. Note that link BD is not reinforced around the pin holes. a. Determine the largest load P that can be applied at A maximizing the shearing capacity of the pin at C. b. Determine the largest load P that can be applied at A maximizing the shearing capacity of the pins at B and D. c. Determine the largest load P that can be applied at A maximizing the axial capacity of link BD.

6. In the steel structure shown, a 6mm diameter pin is used at C and 10mm diameter pins are used at B and D. The ultimate shearing stress is 150 MPa at all connections, and the ultimate normal stress is 400 MPa in link BD. Note that link BD is not reinforced around the pin holes. a. Determine the largest load P that can be applied at A maximizing the shearing capacity of the pin at C. b. Determine the largest load P that can be applied at A maximizing the shearing capacity of the pins at B and D. c. Determine the largest load P that can be applied at A maximizing the axial capacity of link BD.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. The following the truss figure, came from your Module 1. Page 9. B D F 3 m H H. E G 30 kN 70 kN 4 panels at 4 m = 16 m But this time, All the members have a cross sectional area of 850 mm². Find the normal stress of the following members а. EF b. GH c. DF
A 20-mm-thick plate is bolted to the flange of a T-beam to form a 200 mm 20 mm built-up beam. If the beam is subjected to a vertical shear force of V = 200 kN, determine (a) the maximum shear stress in the beam, 10 mm 300 mm (b) the required spacing s of the bolts. The diameter of each bolt is 19 mm, and the allowable average shear stress in the bolts is 140 MPa. 10 mm
Problem 01.054-Analysis of an inverted T-frame In the steel structure shown, a 6-mm-diameter pin is used at C and 12-mm-diameter pins are used at B and D. The ultimate shearin stress is 150 MPa at all connections, and the ultimate normal stress is 340 MPa in link BD. Knowing that a factor of safety of 3.0 is desired, determine the largest load P that can be applied at A. Note that link BD is not reinforced around the pin holes. Front view. 160 mm D B 18 mm B Top view 120 mm largest load P that can be applied at A is 99252 2.328 KN. ED 6 mm 22B Side view
4.1 The aluminum rod AB (Gal = 27 GPa) is bonded to the brass rod BD (Gbr = 39 GPa). The portion CD of the brass rod is hollow and has an inner diameter of 40 mm. If the allowable shear stresses for the aluminum and brass are 90 MPa and 70 MPa, respectively, and the allowable angle of twist of the free end A is 6 degrees, determine the maximum permissible value of T.
The maximum tension in the wèr link of a Porter governor is 580 N and the maximum stress in the link is 30 N/mm?. If the link is of circular cross-section, determine its diameter.
A tension member in a welded steel truss is 4.0 m long and subjected to a force of 15kN. Choose an equallegangle made of ASTM A36 steel that will limit the stress to 149 MPa. Then, compute the elongation in theangle due to the force. Use E = 200 GPa for structural steel
The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A and C. Knowing that the modulus of rigidity is 3.7E6 psi for aluminum and 5.6E6 psi for brass, determine the maximum shearing stress in cylinder AB And cylinder BC in ksi. 1 Aluminum T= 19.6 kip-in. Brass A - 1.4 in. B <-2.1 in. C 10 in. 15 in.
The aluminum rod AB (Gal = 27 GPa) is bonded to the brass rod BD (Gbr = 39 GPa). The portion CD of the brass rod is hollow and has an inner diameter of 40 mm. If the allowable shear stresses for the aluminum and brass are 90 MPa and 70 MPa, respectively, and the allowable angle of twist of the free end A is 6 degrees, determine the maximum permissible value of T. Please show your complete handwritten solution. Thank you
A The member consists of the steel rod AB that is screwed into the end of the bronze rod BC. Find the largest value of P that meets the following design criteria: (i) the overall length of the member is not to change by more than 3 mm; and (ii) the stresses are not to exceed 140 MPa in steel and 120 MPa in bronze. The moduli of Problem 4: Steel A= 480 mm? 1.0 m B elasticity are 200 GPa for steel and 80 GPa for bronze. Problem 5: The compound bar carries the axial forces P and 2P. Find the maximum allowable value of P if the working stresses are 40 ksi for steel and 20 ksi for alumi- num, and the total elongation of the bar is not to exoceed 0.2 in. 3P Bronze A= 650 mm 2 m 3 ft 4 ft 2P Steel A = 0,4 in.2 E = 29 × 10° psi 2P Aluminum A = 0.6 in.2 E= 10 x 10° psi
2) A solid rod with the given dimension shown in Fig. Axial loads are applied at the positions indicated. Find the f a) The max Compressive stress in the system P-60 kN Aluminum A=400 mm b) The max Tensile stress in the system P-60 kN Steel A = 500 mm² Bronze A-200 mm² 4P 2.5 m 1.5 m 2.0 m 2P
Two wooden members of uniform rectangular 150 mm cross-section are joined by a simple glued scarf splice as shown. Knowing that the maximum allowable shearing stress in the glued splice is 620 kPa, determine P. i. the largest load P that can be safely applied 1i. the corresponding tensile stress in the splice. 75 mm
Q2) One brass bar and one steel bar are forming the setup shown below. Determine the stresses and the strains in the steel and brass bars when a load of 750 kN is applied to the connection of these two members where modulus of elasticities for steel and brass are Est = 200 GPa and Ebr 125 GPa, respectively, and cross-sectional areas for steel and brass bars are Ast = 700 mm² and Abr = 1000 mm², respectively. 500 mm 400 mm Brass Steel F Fixed Support 2 mm Gap F = 750 KN Fixed Support