6. The current at the terminals of the two capacitors shown below is 240e-10t HA for t 2 0. The initial values of v, and vz are -10 V and -5 V, respectively. Calculate the total energy trapped in the capacitors as t co. (Hint: Don't combine the capacitors in series- find the energy trapped in each, and then add.) 2 µF 8 µFFV2

6. The current at the terminals of the two capacitors shown below is 240e-10t HA for t 2 0. The initial values of v, and vz are -10 V and -5 V, respectively. Calculate the total energy trapped in the capacitors as t co. (Hint: Don't combine the capacitors in series- find the energy trapped in each, and then add.) 2 µF 8 µFFV2

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter20: Capacitance In Ac Circuits

Section: Chapter Questions

Problem 5PP: Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 -...

See similar textbooks

Similar questions

Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?
List the five capacitor replacement rules.
A postage stamp mica capacitor has the following color marks starting at the upper left dot: yellow, violet, brown, green, no color, and blue. What are the capacitance value, tolerance, and voltage rating of this capacitor?
You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
A series R–L–C circuit comprises a 5µF capacitor, a 4ohm resistor and a variable inductance L. The supply voltage is 10∠0◦ V at a frequency of 159.1 Hz. The inductance is adjusted until the p.d. across the 4 ohm resistanceis a maximum. Determine for this condition (a) the value of inductance, (b) the p.d. across each component and (c) the Q-factor of the circuit.
The figure below shows a simple RC circuit with a 3.30-μF capacitor, a 4.40-M resistor, a 9.00-V emf, and a switch. What are the following exactly 9.00 s after the switch is closed? (a) the charge on the capacitor 13.7204 UC (b) the current in the resistor 0.0110522 x Your response is off by a multiple of ten. HA (c) the rate at which the capacitor is storing energy μW (d) the rate at which the battery is delivering energy μW
Please explain this question properly A capacitor has a reactance of 40 when operated on a 50 Hz supply. Determine the value of its capacitance. In a series R–L circuit the p.d. across the resistance R is 12V and the p.d. across the inductance L is 5V. Find the supply voltage and the phase angle between current and voltage
Compute the individual values and the total values of the capacitance, and voltage of the series circuit. Capacitances are, 2.5 x10^-12F and 4.1x10^-12F with a voltage of 1500V.
At 0-, no currrent flows through the capacitors because they are open, how did you combine the capacitors for the voltage divider since it is the capacitance value and not reactance, is it right? Can we just combine the capacitance value? Please explain. I did not understand..
Find the equivalent inductance of the circuit shown in the figure. 0.06 H 0.04 H 0.06 H 0.06 H
9 calculate the cuanent to cwirg thnough +the 5mH inductoRo () calculate the voltage () the enengy stoned by the indue ton the enengy stored the capacitoR Assume, the indueton and the eapacitor