7- Methods for measuring mass flow rates of gases and liquids flowing in pipes and ducts include: rotameters, turbine flowmeters, orifice-type flowmeters, thermal flowmeters, and Coriolis-type flowmeters. Determine the principles of operation of each of these flow-measuring devices. Consider the suitability of each for measuring liquid or gas flows. Can any be used for two-phase liquid-vapor mixtures? Which measure volumetric flow rate and require separate measurements of pressure and temperature to determine the state of the substance? Summarize your findings in a brief report.

7- Methods for measuring mass flow rates of gases and liquids flowing in pipes and ducts include: rotameters, turbine flowmeters, orifice-type flowmeters, thermal flowmeters, and Coriolis-type flowmeters. Determine the principles of operation of each of these flow-measuring devices. Consider the suitability of each for measuring liquid or gas flows. Can any be used for two-phase liquid-vapor mixtures? Which measure volumetric flow rate and require separate measurements of pressure and temperature to determine the state of the substance? Summarize your findings in a brief report.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

6, Select the correct order of steps in the drop down lists below for the graphical analaysis method to determine the area required at the throat of a nozzle flowing a condensable vapour for a given set of inlet and exhaust conditions 1 Chick for List 2. Calculate the area per unit mass flow rate Determine the specific volume at each intermediate pressure 3. Determine the specific enthalpy at each intermediate pressure 4. Plot a chartigraph of showing the variation of area per unit mass flow rate against pressure 5. Locate the minimum to determine the approximate throat location and critical pressure 6. Determine the value of dryness fraction at these intermediate pressures 7. Divide the change of pressure into a number a pressure steps
Plot curves on a single plot that display the relationship between the pressure generated by thepump as a function of flow rate of water at 20 °C through the three branches of the piping systemshown below (delta P on the y axis and flow rate on the x axis; therange of the pressure as 0 to ~1 MPa). Pipe inner diameter: 0.0254 mPipe material: copperTypical mass flow rate of interest: 0.5 kg/sIgnore minor losses of tee's at points A and B and any features of branch 3Consider minor losses of two 90° elbows in branch 2
Question - You must discuss in detail the way in which the pitot tube and nozzle flow meter are used to calculate velocity or volume flow rate. Write the velocity (or flow rate) equations for both and a detailed description of the what you did.
) where AP is the static The Hagen-Poiseuille equation for the laminar flow through a circular pipe is: AP pressure drop measured over some length of pipe, L. Use the Hagen-Poiseuille equation and the Darcy-Weisbach equation to derive an expression for the fanning friction factor, f, for laminar flow through a circular pipe where Re is the Reynolds number. Choose one answer from the list below: of= of O None of the above 32 Re 16 Re O f = 64 Re = o f = 32μLc 3 d² 8 Re O f = 16 Re
Select the correct order of steps in the drop down lists below for the graphical analaysis method to determine the area required at the throat of a nozzle flowing a condensable vapour for a given set of iniet and exhaust conditions 1 Click for List 2 Calculate the area per unit mass flow rate 3 Determine the specific volume at each intermediate pressure Determine the specific enthalpy at each intermediate pressure 4. Plot a chartigraph of showing the variation of area per unit mass low rate against pressure Locate the minimum to determine the approximate throat location and cntical pressure 6. Delermine the value of dryness fraction at these intermediate pressures 7. Divide the change of pressure into a number a pressure steps
The temperatures of the 20 ºC 25 ºC 30 ºC water at outlet Task 1 Explain the system parameters using the Non- Flow Energy Equation
Assuming the clearance is negligible for a single stage compressor with the following data.Atmospheric pressure: 90 kPaAtmospheric temperature: 17 ˚CDelivery pressure: 7 barFree air delivery flow rate: 0.2 m3/minTake “n” as 1.3, cp = 1.005 kJ/kg K, cv = 0.718 kJ/kg K 1.What is the power input to the compressor in kW to 2 decimal places if the compression is polytropic compression process with n=1.25?
When ventilating the patient on a time-cycled/pressure-limited ventilator, what parameters determine the tidal volume delivered? How can these values increase tidal volume? How can they decrease tidal volume?
5. The total head of a fan is 185 m and has a static efficiency pressure of 210 mm of water gage.What is the velocity of air flowing if the density of air is 1.15 kg per cubic meter? 8. A coal fired steam boiler uses 3000 kg of coal per hour. Air required for combustion is 15.5 kg ofcoal at barometric pressure of 98.2 KPa. The flue gas has temperature of 285 degree Celsiusand an average molecular weight of 30. Assuming an ash loss of 11% and allowable gas velocityof 7.5 meters per second. Find the diameter of the chimney 9. The gas density is 0.75 kg per cubic meters and air density is of 1.15 kg per cubic meter. If thedriving pressure is 0.25 KPA. Determine the height of the chimney. 10. A powerplant situated at an altitude having an ambient air of 96.53 KPa and 23.88 degreeCelsius. Flue gases at a rate of 5.0 kg per second enter the stack at 200 degree Celsius andleaves at 160 degree Celsius. The flue gases gravimetric analysis are 18% CO2, 7% O2 and 75%N2. Calculate the height of…
Assuming the clearance is negligible for a single stage compressor with the following data.Atmospheric pressure: 90 kPaAtmospheric temperature: 17 ˚CDelivery pressure: 7 barFree air delivery flow rate: 0.2 m3/minTake “n” as 1.3, cp = 1.005 kJ/kg K, cv = 0.718 kJ/kg K 1.What is the power input to the compressor in kW to 3 decimal places if the compression reversible isothermal?
Subject : Thermofluid Question : Air at 20oC flows in a 0.60 m diameter pipe at a rate of 15 m3/s as shown in Figure 3. The pipe diameter changes to 1.2 m through a sudden expansion. i. Assess the pressure rise across this expansion. ii. Explain how there can be a pressure rise across the expansion when there is an energy loss (KL ≠ 0).
The pressure of a reactor vessel can be adjusted bychanging either the inlet or outlet gaseous flow rate. Theoutlet flow is kept fixed as long as the tank pressure remainsbetween 100 and 120 psi, and pressure changes are treatedby manipulating the inlet flow control valve. However, if thepressure goes higher than these limits, the exit gas flow isthen changed. Finally, if the pressure exceeds 200 psi, a ventvalve on the vessel is opened and transfers the gas to a storagevessel. Design a control scheme that meets the performanceobjectives. Draw a process instrumentation diagram for theresulting control system