7.10 - A voltage source = 120/30° is connected to a circuit consisting of R = 3.5.2 in serieswith L = 0.0833 H. If the circuit is energized in Europe, compute the following:a. The load currentb. The load power factorc. The real power consumed by the loadd. The reactive power consumed by the load

Answered: 7.10 - A voltage source = 120/30° is…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.13MCQ

See similar textbooks

Similar questions

The real power delivered by a source to two impedances, Z1=4+j5 and Z2=10 connected in parallel, is 1000 W. Determine (a) the real power absorbed by each of the impedances and (b) the source current.
Need asap pls help. Solve for the voltages across and currents through each component. Show the complete solution and explain. The total power should be zero..
15 A of current is taken by a non-inductive load at 125 V. In order that the same current shall be generated from 240 V, 50 Hz mains. An inductor is now also then connected in series. Note: The resistance of the inductor should be ignored and also assume the waveform to be sinusoidal. Determine the phase difference between the current and the applied voltage, the impedance of the circuit and the inductance of the inductor.
For the system in the figure: Find the total average power, total reactive power, total apparent power, and total power factor. Find the current Is (in phasor form). If the loads can be modeled as a resistance in series with a reactive element (capacitor or inductor), find the impedance of each load. Confirm the result of part B using the input voltage and the result of part C. ..
Draw the sinusoidal waveform of the AC voltage and current for the given loads below. Describe the characteristics of the waveform for each load. A. Pure resistor B. Pure inductor C. Pure capacitor
The total power drawn by the two-impedance load in parallel is 26kW at 0.98 power factor lagging, it is being supplied by a 230-volts AC source. One of the loads (Load 1) takes 16kVA at 0.77 power factor lagging. What is the reactive power of the unknown impedance (Load 2)?
An impedance load consisting of 12 ohms resistance and 16 ohms inductance reactance is connected across a 50 Hz, 100 V source. Find the capacitance of the condenser which may be paralleled with this load to bring the power factor to 0.80 leading.
The power factor of the circuit shown in figure 2 is. a. 0.866 lagging b. 0.5 lagging c. 0.707 lagging d. 1
Lance Smile operated two loads in parallel. The loads draw a total of 3kW at a 90% power factor lagging operating at a 230 Vrms 60-hz voltage source. Load 1 is taking 1000 W at 80% power factor lagging. Determine the following: a. The power factor of the second load. b. If a capacitor is connected in parallel with the loads, what is the value of the capacitance needed to correct the power factor to 95% lagging for the combined load.
An impedance load consisting of 12 ohms resistance and 16 ohms inductance reactance is connected across a 60 Hz, 100 V source. Find the capacitance of the condenser which may be paralleled with this load to bring the power factor to 0.80 lagging.
a-Calculate and draw the load current for the steady-state condition b-Find the RMS values of the load voltage and the load current
Calculate the rms values of load voltage and current for the circuit shown below. Please show work

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning