710. Use conjugate beam method in the following problems. Show your complete solutions and drawings.Subject: Structural Theory 710. Two timber beams are mounted at right angles and in contact with each other attheir midpoints. The upper beam A is 2 in. wide by 4 in, deep and simply supportedon an 8-ft span; the lower beam B is 3 in. wide by 8 in. deep and simply supportedon a 10-ft span. At their cross-over point, they jointly support a loadP =Determine the contact force between the beams.2000 lb.

Answered: Image /qna-images/answer/38e40ad7-2bb3-464e-8a1c-8453ed95865a.jpg

Answered: 710. Use conjugate beam method in the…

710. Use conjugate beam method in the following problems. Show your complete solutions and drawings. Subject: Structural Theory

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Two simply supported beams are made up of the same material and are of the same cross-section. Both…

A: given- 2 simply supported beams-same material and same cross-sectionSame UDLspan of beam=2 m and 4…

Q: General instructions: 1. Analyze completely the loaded frame shown below. Draw all free body…

A: Solution: Find Horizontal and Vertical reaction; ∑H=0 HA+HE=12×5=60 KN∑V=0RA+RE=0(B.M)C=0 From…

Q: A rigid triangular plate is suspended from a horizontal plane by three vertical wires attached to…

A: Diameter = d = 1mm Modulus of Elasticity = E = 196000Nmm2 Length of each wire = L = 1440mm Ratio of…

Q: Find the joint forces in the system shown.

Q: Calculate the depth of compression block of the section in PART A in mm.0

Q: The simply supported beam is subjected to the force F = 730 N and the uniform distributed load with…

Q: rigid beam is being supported by three suspender bars made of bronze and loaded as shown in the…

A: Given a rigid beam is being supported by three suspender bars made of bronze and are subjected to…

Q: Two wires support a weight W. The stresses in the wires AB and AC are not to exceed 131 MPa and 192…

Q: The frame shown is used to support high voltage cables. If b = 3 feet, a (alpha) = 30 ° and W = 200…

A: To determine the axial force in element HJ, we will need to apply the concept of static equilibrium.…

Q: Subject/ Plates and shells theory Square Plate Caxa) simplysupported on all Face edges is Subjected…

Q: A mass of 50 kg achieves a velocity of 2 m/sec when it strikes the solid squared (side = 60 mm) beam…

Q: Discuss in details the importance of studying strength of materials and its applications Discuss in…

A: As per guidelines, we have to answer only one question please load the remaining questions…

Q: Courne Time: sk/m 2m B y at pt lom

Q: Two simply supported beams are made up of the same material and are of the same cross-section. Both…

A: Given, load on both beam (udl) =w L1=2mL2= 4mEI= same δ1=1 mm

Q: In the wood industries, inclined blocks of wood are sometimes used to determine the compression…

Q: In finite element modelling of tall steel buildings to evaluate the lateral deflection, the ratio…

A: The ratio between the effective moment of a beam to its gross moment of inertia is 0.4

Q: 4 in 0375 in. 1,200 lb 0375 in 450 Ib/ft K in. C 0.375 la. 14 ft 6 ft

Q: Q2: Use dimensional analysis to derive an epresion for the power developed by an engine in terms of…

A: Given Power=P Torque=T Rotation speed=ω

Q: Give an example for type of load classification according to time Static load - Sustained…

Q: A beam is subjected to a concentrated force, as shown in the figure below, try to find the Elastic…

Q: This is a question from mechanics of material book (axial load chapter). I need the correct solution…

A: We know, E=σεand σ=stress=P/Aand ∈=strain=∆l/Land ∆l=PLAE

Q: Effect of temperatures and rate of pulling on ductility value.

A: Ductility test on bitumen is done to test the adhesive property of the bitumen and its ability to…

Q: True or false F. A structural engineer is a civil engineer who oversees the design and…

Q: A steel plate 2.2 m x 1.4 m x 100 mm thick is to be hoisted by a steel cable sling as shown in the…

A: To determine the vertical displacement of the steel plate. Given, Unit weight of steel = 77.3…

Q: 2. As shown in the figure, a rigid beam with negligible mass is pinned at one end and supported by…

Q: Part 1 For the simply supported beam subjected to the loading shown, derive equations for the shear…

Q: es! Thank you in adv

Q: effect of temperature and rate of pulling on ductility value

A: It is the transition temperature below which a ductile plastic specimen becomes brittle, i.e. when…

Q: Find the solution of following Differential Equation where the solution represents the deflection…

A: Deflection at point b is solved by solving differential equation Here y represents deflection at…

Q: 09. The rigid bar of negligible weight is supported as shown in the figure. If W 80 kN, compute the…

A: Given DataW = 80 KNtensile stress in stell rod = 50 MPa (σs)Equilibrium…

Q: The bottom of a steel "boat" is a 7 m ✕ 8 m ✕ 6 cm piece of steel (ρsteel = 7900 kg/m3). The sides…

A: The dimension of the bottom of the steel boat is 7 m×8 m×6 cm. The density of steel is ρSteel=7900…

Q: A 10 kN ww E G BD F H K 8 @ 2m = 16 m L 5 kN www 15 KN O M N P 4.0m

Q: LABORATORY NO. 1 Find the equation of the elastic curve of the beam shown below. Wo

Q: The figure shows a cantilever of length L= 4 m consisting of steel angles size of 100 x 100 x 12 mm…

A: Introduction- A cantilever is a horizontal extending rigid structural component with just one end…

Q: Problem 1: The force F has a magnitude of 80 lb and acts within the octant shown. Determine the…

A: F=80lb To find x,y and z components of force F

Q: STRENGTH OF MATERIALS. Please show the complete solutions. NO LONG EXPLANATION NEEDED! Rate will be…

Q: The force F has a magnitude of 80 lb and actswithin the octant shown. Determine the magnitudes of…

Q: Theory of Bending and Deflection 12 in, 12 in 27 in 6 in. The following diagram will be used as a…

Q: Construct the shear force and bending moment diagrams for the beam shown by the area method. Neglect…

Q: Given figure shows a portal frame with loads. All members of frame have same plastic moment of…

A: We have to determine the collapse load W according to plastic analysis of the frame according to the…

Q: 3- Newton's law of viscosity relationship between a) Pressure, velocity and tem b) Shear stress and…

Q: Problem 6.2. The undeformed and deformed outline of a material element are as shown in the figure…

A: Solution- Consider the diagram shown below, And,

Q: A steel tape is 100 m long at a temperature of 20°C and a pull of 10 kg. It was used to measure a…

Q: 3 cm 7 cm 6 cm Determine the Following

Q: Question 1 The figure shows a horizontally rigid beam whose own mass is m. The beam is homogeneous…

A: As per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost other…

Q: STRENGTH OF MATERIALS. Please show the complete solutions. NO LONG EXPLANATION NEEDED! Rate will be…

A: Given, A simply Supported beamof span 6m, which is subjected to a point load of 40KN at a distance…

Q: Solid Mechanics A beam with the cross-section given below is subjected to a positive bending moment…

Q: Fundamental Problem 4.41 Part A Determine the resultant force and specify where on the beam measured…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: Q1. Determine the slope and deflection of the free end C of the beam loaded as shown in Fig.…

A: Consider the free body diagram of the given beam as shown below. Flexural Rigidity, EI=Constant.

Q: Select the correct statement among the following? a. Maxwell Reciprocal theorem states that in any…

Concept explainers

Matrix Algebra for Structural analysis

Structural analysis is a process in which the effects of different loads and internal forces, acting on structures and their elements are determined. This method of analysis is effective in detecting the failure loads of the structural elements and the design can be altered before commencing the construction process, which ensures proper strength and safety of the structures.

Question

710. Use conjugate beam method in the following problems. Show your complete solutions and drawings. Subject: Structural Theory

710. Two timber beams are mounted at right angles and in contact with each other at
their midpoints. The upper beam A is 2 in. wide by 4 in, deep and simply supported
on an 8-ft span; the lower beam B is 3 in. wide by 8 in. deep and simply supported
on a 10-ft span. At their cross-over point, they jointly support a loadP =
Determine the contact force between the beams.
2000 lb.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the reactions of A & B for the steel bon and leasing as given abuming that 4.5 mm clearance exist bin the bar and the ground before the loads are applied. Assume E = 200 GPG. P₁ = 300 KN P₂ = 600 KN A₁ = 250 mm² A₂ = 400 mm² 5 R 4 3 2 1 & P VA 0 B P₂ 150mm 150m 150mm 150mm 4.Sm
Q6: If the cretical load for a Two ends fixed coulmn is 60 kN, what s the critical load for the other ends support conditions : ( show your . calculations ) a. One fixed end and one free end (flage pole )? b. Two ends pinned.? c. One fixed end and the other is pinned.?
Shown below is a triangular truss with members that are symmetrical with the vertical middle members. A load W (N) acts at the middle joint in the lower chord. Show that their is no force in the members between the upper and the lower chords except in the middle vertical member. Draw a conclusion from the result. D Y vima to zotein toesup of bablew to be Bd on o riose is berintenutounde eeunt leen is nietud erit en:C not blat eised any ou na sillf-azint teors at A X el ti mettia omatsnemuonoos moool rymmoos nem ni econot sixs stitannia (2 of) elozzug (do enoifennosnig plane as etnioj eeur art & sisebi of eldissimsc H RA='W/2 (N) E W (N) L (m) CE = EG = GH = DE = L/4 (m) BC= FG = DE/2 = L/8 (m) (Angle DCE = 45°; Angle BAC = 26.6°) AC G RH = W/2 (N) 1
A 100 mm x 200 mm wooden beam with a clear span of 7.2 m is embedded firmly ea one end and is simply supported on the other end as shown in the figure. If the allowable stresses are respectively 13.8 MPa and 1.11 MPa for bending and shear, ODetermine the safe maximum uniform load the beam can carry. Yeight of wood is 9.9 kN/m3 Find the reaction at B. OFind the max, moment of the beam.
04. Analyze completely the compound truss loaded as shwon below. D 24 kN 3 m E 2 m F 3 @ 4 m 12 PROBLEM 4 TABLE OF ANSWERS: МЕМBER NUMBER FORCE (k) AB 1 CD 2 EF 3 BC CF 5 BF 6 DE 7 AD 8 AE 9 4.
Two wheels, placed at a distance of 2.5m apart, with a load of 200 kN on each of them are moving on a simply supported girder (I-section) of span 6.0m. The top and bottom flanges of the l-section are of 200 x 20 mm and the size of web plate is 800 x 6 mm. If the allowable and average stresses are 110 MPa, 165 MPa and 100 MPa respectively, check the adequacy of the section against bending and shear stresses (self-weight of the girder, may be neglected)
P A B |▬2 m▬★▬2 m▬▬2 m▬▬2 m| The rigid beam is supported by three post of equal length Post A and C are made of aluminum material and has a diameter of 75 mm, Modulus of Elasticity of 70 GPa and has an allowable stress of 20 MPa. Post B is made of bronze material for which has a Modulus of Elasticity of 100 GPa and allowable stress of 590 MPa. Post B has a diameter of 20 mm. Determine the smallest magnitude of P.
A wooden beam is fabricated from one 2 x 8 and two 2 x 6 pieces of dimension lumber to form the I-beam cross section. The flanges of the beam are fastened to the web with nails that can safely transmit a force of 119 lb in direct shear. If the beam is simply supported and carries a 1020-lb load at the center of a 14-ft span, determine: (a) the horizontal force FH transferred from each flange to the web in a 14-in.-long segment of the beam. (b) the maximum spacing s (along the length of the beam) required for the nails. (c) the maximum horizontal shear stress Tmax in the I-beam. 2 in Nails Answers: (a) FH = 6 in (b) s = (c) Tmax= 2 in. 8 in 2 in lb. in. psi.
. A beam is constructed from a reinforced 50mm x 200mm section of timber using two L120x80x12 steel angle sections. Considering that the effort allowable stress in wood is 10 MPa, and the allowable stress in steel is 110 MPa. Determine the maximum positive and negative moment that the beam can support
A compo beam is fabricated by bolting two 2.6-in.-wide by 13-in.-deep timber planks to the sides of a 0.5-in. by 13-in. steel plate. The mod elasticity of the timber and the steel are 1970 ksi and 28800 ksi, respectively. The simply supported beam spans a distance of 17 ft and carries two concentrated loads P, which are applied as shown. Assume LAB=LCD= 4 ft, LBc = 9 ft, b = 2.6 in., d=13 in. and t = 0.5 in. (a) Determine the maximum bending stresses o,, o, produced in the timber planks and the steel plate if P = 3.7 kips. (b) Assume that the allowable bending stresses of the timber and the steel are 1080 psi and 23900 psi, respectively. Determine the largest acceptable magnitude for concentrated loads P. (You may neglect the weight of the beam in your calculations.) Answers: (a) o, = (b) P= i LAB i B b LBC F Cross section C ksi, o, = kips. LCD i D ksi. 0000000
A 300 lb crate is on top of a 70 lb pickup tailgate. Determine the tension in Ib in each of the two restraining cables. The weight of crate and tailgate acts n G2 and G1 respectively. 14"- 12" 9.5"- 2.75"
Determine the tension at A & B.