ConriderRLC- ciruitCaElt)= F. in cot)R- Resis tamie (ohm, 2): voltage drop = RIL- Inductunce ( hnry, H) :dtIPC - Capeci tamce ( Farad, F)ICt) is the current in thecircuit otGohenefime tany•QC+) is the amount of charge in caperitor atfime t.any· ECt) is the oytemal voltage providedto circuit. Here, ECt) = Eo sin cwt).· Rdatondhipaurentin the capacitor be tuleen chorogeandisI= dQdtFind the current inR- 11 2, L- 0•1 H, C=102 FConnectedRLC- circnit withanw hichistocorarce of EMF.aElt) = 110 sin (1201+).Assume thatat t-0.current and capacitor chargeare

We need to find out current through given circuit

Answered: 85. Find the current in R= 11 2, L= 0•1…

85. Find the current in R= 11 2, L= 0•1 H, C= 102 F Connected an RLC- circnit with w hich is to coarce of EMF. a Elt) = 110 fin (1201t). Assume that current and copaaiter charge o aut t=0. are

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What voltage is boosted at the output of a multiplier.Choices: average, rms, peak, or instantaneous Which assumption is not used in the analysis of multipliers?Choices: a capacitor will not discharge, start with the cycle of the source that will forward bias the nearest diode, the output will always be multiplied, or a single diode is forward biased at a time A voltage multiplierChoices: multiplies the output voltage, has very high voltage and low current ,can employ inductors, or may not have equal numbers of diodes and capacitors A voltage regulator maintains constant voltage at the load regardless of variations atChoices: the input and output, the load, source, or in the environment Between a lower percent regulation and a higher one, which is better?Choices: lower or higher
I ln. l. . :D docs.google.com/forms/d/e/1l Diode clippers are wave-shaping circuits in that they are not used to prevent signal voltage from going above or below certain * .levels TO F like that of the clipper, the shape of the .input signals of a clamper is changed F The clamping circuit clamps or shift the * .input sinusoidal signal up or down FO II
Step-down chopper circuit connected to 100V d.c source supplies with inductive of 40mH the load resistive of 5Q, and a freewheeling diode is placed to the load . the load current varies between 12A and 16A, determine time ratio of the chopper.
Determine the forward voltage and forward current of a diode in a circuit. The circuit is composed of a dc voltage source with its positive terminal of 10V connected in series to a 1Kohms resistor and the anode of a diode. The cathode of the diode is connected to ground. Use ideal device model approach. Draw the circuit and show your solution/s.
4) Determine the value of branch current, I1 and I25) Determine the value of voltage across resistor, R1, R2 and R36) Determine the value of voltage across capacitor, C1 and C27) Determine the value of voltage across inductor, L.
Explain the given circuit diagram and also explain its functions with suitable examples. Rubrics: Explain the functions of given IC function(s) with suitable example. Write down the formula for charging, discharging time and the frequency.
A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Va.. (t) 10 kO 8V 10 kO Vin Vin(t) D2 Vout(t) RL Ims D1 6V -8V 4V Page | 1
•A system consists of ,The electric potential opplied to this cell droes o cubie cell, to 1oV from 30OV in one step. •Whot is the hork done? •Whot wald the work done be if it hernt from 3or to 20v and then to lov?
We want to investigate how the field strength will be with air as dielectric and with steatite. A plate capacitor is placed in a 24 kV network between phase and ground. The relative permittivity of air is &=1 and for steatite &-6. The plate capacitor has area = 1m². The distance between the electrodes is 2 mm. Ep = 8.854-10-12 F/m A=1m² d=2mm a) Calculate the maximum field strength in the plate capacitor. (Answer: 9.8kV/mm) b) What is the capacitance of the capacitor if we use steatite? (Answer: C = 26.6nF)
Problem 3 For the circuit shown below, assume that: R=20kQ, D1, D2, D3 and D4 are modeled by a battery of 0.8 V and rB = 30Q, the Zener diode has 5 V breakdown voltage and rz= 502. 'Vin' is a sinusoidal signal with 1 kHz frequency and amplitude voltage of 15 V: • Sketch 'Vout' and Iz' for -15V< Vin <15V. • Plot 'Vout' and Iz’ versus time • What is the function of this circuit? Vout w- + + D4 D, Vin D
The current through the diode in the circuit given in the Figure below when Vy = 0.7 V is? ww 8092 12V Select one a. 24.26 mA b. 13.09 mA c. 58.23 mA d. 40.13 mA 40-52 ww 3092 ID
The step up chopper has R=20 ohm and out put voltage is 120V. The source voltage is 40V DC . The load inductance is 0.2mH. If the chopper frequency is 4KHZ find1- the duty cycle2- the average value of source current3- TON4- Imax5- Imin6-The average value of diode current