9. The following circuit is a voltage limiting circuit. The diode has an offset voltage of 0.7 V. (a) Determine the maximum & minimum voltages for Vout(t) for both the positive and negative cycles of Vin(t) (b) Calculate the maximum current flow during the positive cycle of Vin(t) (c) Sketch the waveforms for Vin(t) and Vout(t) for 2 cycles, indicate on the waveform the period, maximum and minimum values.

9. The following circuit is a voltage limiting circuit. The diode has an offset voltage of 0.7 V. (a) Determine the maximum & minimum voltages for Vout(t) for both the positive and negative cycles of Vin(t) (b) Calculate the maximum current flow during the positive cycle of Vin(t) (c) Sketch the waveforms for Vin(t) and Vout(t) for 2 cycles, indicate on the waveform the period, maximum and minimum values.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the circuit shown in the figure below, consider the diode as an ideal diode & R.M.S value of source voltage as Vs. The output voltage waveform at R is most likely to have zero value in the positive half cycle and a peak value of 1.414Vs in the negative half суcle sine-wave nature with a peak value 1.414VS zero value in the negative half cycle and a O peak value of 1.414Vs in the positive half сycle O sine-wave nature with a peak value Vs
I ln. l. . :D docs.google.com/forms/d/e/1l Diode clippers are wave-shaping circuits in that they are not used to prevent signal voltage from going above or below certain * .levels TO F like that of the clipper, the shape of the .input signals of a clamper is changed F The clamping circuit clamps or shift the * .input sinusoidal signal up or down FO II
What voltage is boosted at the output of a multiplier.Choices: average, rms, peak, or instantaneous Which assumption is not used in the analysis of multipliers?Choices: a capacitor will not discharge, start with the cycle of the source that will forward bias the nearest diode, the output will always be multiplied, or a single diode is forward biased at a time A voltage multiplierChoices: multiplies the output voltage, has very high voltage and low current ,can employ inductors, or may not have equal numbers of diodes and capacitors A voltage regulator maintains constant voltage at the load regardless of variations atChoices: the input and output, the load, source, or in the environment Between a lower percent regulation and a higher one, which is better?Choices: lower or higher
For a sinusoidal input of 40 V (p-p) to the given circuit, what is the minimum value of the output waveform? NOTE: * use ideal diode
By comparing other diodes, reverse recovery time of Schottky diode is lower. Select one: O True O False is the RMS value of output voltage of the step down chopper which is having 240 V as a input for a duty cycle of 60 %.
A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Vaue (t). 10 k. 8V 10 kN. D2 RL Vourlt) Vin= Vin(t) Ims D1 6V -8V 4V Page | 1
A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Va.. (t) 10 kO 8V 10 kO Vin Vin(t) D2 Vout(t) RL Ims D1 6V -8V 4V Page | 1
Plot the Vi, Vd and Id signals for the following circuit. Diode is ideal. The input waveform period is T it is a sinusoidal wave.
For the circuit shown in Figure 2, sketch the output voltage (across the load 2.2 KN resistor) and the load current (through the load 2.2 Kn resistor). Sketch the diode voltage (across the diode D1) and the diode current (through the diode DI). The input V. is sinusoidal with maximum amplitude (peak) of 100 V and frequency of 700 Hz. The diode DI is a Silicon diode. The sketches have to be at least for two cycles of the input. D1 2.2 K2 Vi
For a sinusoidal input of 40 V (p-p) to the given circuit, what is the minimum value of the output waveform? NOTE: use ideal diode 0.7 30 20 -5 -40 K
In the circuit of the following figure, the input voltage Vs is 15 volts rms with a frequency of 60 Hz, R equals 150 Ohms and C equals 100,000 Pico Farads. The diodes are Germanium (Vd = 0.2 volts) and the Zener diode is 12 volts. a) The magnitude of the ripple voltage at Cb) The Magnitude of the Peak Inverse Voltage (PIV) for D1 and D2.
7) sine wave. Sketch the waveform (1 period is enough) for the resulting Vout- What are its positive and negative peak values? (AVforward,ideal = 0) For each of the ideal-diode circuits below, the input Vin is a 1kHz 5-V peak a) b) Vin Vaut Vin Vaut 1kN 1kN c) c) Vin Vout Vin Veut 1kN 1kN e) f) Vin 1kN Vaut Vin 1kN Vout 太太