A 15 KVA, 10.8 KV/240-V, 60 Hz, single-phase conventional transformer is supplying 12 KW of power to a load at 0.8 Lagging power factor a load voltage of 240 Volts. Its Equivalent circuit is given below. Calculate the magnitude of the input voltage of this transformer. alp +0 2440 $2 0.808+j 4.04 $2 Texs Ims Vs 1700.32 Select one: O a. Vp = 18.03 KV O b. None c. Vp = 20.92 KV = O d. Vp 12940.4 Volts Clear my choice

A 15 KVA, 10.8 KV/240-V, 60 Hz, single-phase conventional transformer is supplying 12 KW of power to a load at 0.8 Lagging power factor a load voltage of 240 Volts. Its Equivalent circuit is given below. Calculate the magnitude of the input voltage of this transformer. alp +0 2440 $2 0.808+j 4.04 $2 Texs Ims Vs 1700.32 Select one: O a. Vp = 18.03 KV O b. None c. Vp = 20.92 KV = O d. Vp 12940.4 Volts Clear my choice

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.34P: Three single-phase, two-winding transformers, each rated 450MVA,20kV/288.7kV, with leakage reactance...

See similar textbooks

Similar questions

For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
In developing per-unit circuits of systems such as the one shown in Figure 3.10. when moving across a transformer, the voltage base is changed in proportion to the transformer voltage ratings. (a) True (b) False
A 23/230-kV step-up transformer feeds a three-phase transmission line, which in turn supplies a 150-MVA,0.8 lagging power factor load through a step-down 230/23-kV transformer. The impedance of the line and transformers at 230kVis18+j60. Determine the tap setting for each transformer to maintain the voltage at the load at 23 kV.
The ideal transformer windings are eliminated from the per-unit equivalent circuit of a transformer. (a) True (b) False
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.
Consider Figure 3.4. For an ideal phase-shifting transformer, the imda nce is unchanged when it is referred from one side to the other. (a) True (b) False
For an ideal 2-winding transformer, the ampere-turns of the primary winding, N1I1 is equal to the ampere-turns of the secondary winding, N2I2 (a) True (b) False
Three single-phase, two-winding transformers, each rated 450MVA,20kV/288.7kV, with leakage reactance Xeq=0.10perunit, are connected to form a three-phase bank. The high-voltage windings are connected in Y with a solidly grounded neutral. Draw the per-unit equivalent circuit if the low-voltage windings are connected (a) in with American standard phase shift or (b) in Y with an open neutral. Use the transformer ratings as base quantities. Winding resistances and exciting current are neglected.
The ratings of a three-phase three-winding transformer are Primary(1): Y connected 66kV,15MVA Secondary (2): Y connected, 13.2kV,10MVA Tertiary (3): A connected, 2.3kV,5MVA Neglecting winding resistances and exciting current, the per-unit leakage reactances are X12=0.08 on a 15-MVA,66-kV base X13=0.10 on a 15-MVA,66-kV base X23=0.09 on a 10-MVA,13.2-kV base (a) Determine the per-unit reactances X1,X2,X3 of the equivalent circuit on a 15-MVA,66-kV base at the primary terminals. (b) Purely resistive loads of 7.5 MW at 13.2 kV and 5 MW at 2.3kV are connected to the secondary and tertiary sides of the transformer, respectively. Draw the per- unit impedance diagram, showing the per-unit impedances on a 15-MVA,66-kV base at the primary terminals.
Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.
The direct electrical connection of the windings allows transient over voltages to pass through the auto transfonner more easily, and that is an important disadvantage of the autotransformer. (a) True (b) False
1-A single-phase power system is shown in Figure below. The power source feeds a 100- kVA 14/2.4-kV transformer through a feeder impedance of 40.0 + j150 &. The transformer's equivalent series impedance referred to its low-voltage side is 0.12 + j0.5 &. The load on the transformer is 90 kW at 0.80 PF lagging and 2300 V. 40n j150n 0.12n j0.5n Load 90 kW 0.85 PF lagging source Source Feeder Transformer Load (transmission line) (a) What is the voltage at the power source of the system? (b) What is the power losses in the feeder?