Witg steps please A 235V, 50HZ, single phase motor takes current of 6Aat a PF of 0.5 lagging. Determine the value ofcapacitor required to improve the PF to 0.91.Active component of the current, OP=Reactive component of the current, PR=I(new) taken by the motor with capacitor connected,OQ=Active component of the current (with capacitor), PQ=Capacitor current, Ic=The value of the Capacitor is

As per our guidelines, we can answer only first 3 sub parts, kindly repost the question with other…

Answered: A 235V, 50HZ, single phase motor takes…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

An induction motor is rated 5 HP, 75% power factor and 220 V. What approximate size of capacitor (VAR) is necessary to raise the power factor to about 95%?
A 40kW induction motor with a lagging power factor of 0.76 is supplied by a 120Vrms 60Hz sinusoidal voltage source. find the capacitance needed in parallel with the motor to raise the power factor to (a) 0.9 lagging and (b) 1.0
4. An induction motor draws 4.5 A at a 0.75 lagging power factor from a 208V, 60 Hz source. a) What value of capacitance must be connected in parallel with the motor to raise the overall p.f. to 1. b) Calculate the magnitudes of the motor current, capacitor current and source current with the capacitor in place. 5. A 3-phase Y-connected motor is connected to a three phase Y-conected source with 440V line voltage. It draws a line current of 5A from the source. If the power factor of the motor is 0.8, calculate a) Active power and Reactive power absorbed by the load b) Total Apparent power
An ac controller has a resistive load of R = 10 2 and the input is 220 V, 50 Hz. The thyristors switch is on for n 25 cycles and for m 75 cycles. Determine: (i) (ii) (iii) the rms value of the output voltage, the input power factor, the average and rms current through thyristors.
A generating voltmeter is required to measure voltage between 15kV and 250kV. If the indicating meter reads a minimum current of 2uA and maximum of 35uA. Assume that the speed of driving synchronous motor is 1500rpm. Determine the capacitance of the generating voltmeter. A. 1,2 pF B. 6.5 pF C. 15,2pF D. 1 pF
Q9 / What are the function of brushes , pole and commutator in DC machine
Write a MATLAB program describing the following figure. one cycle TIME PRESSURE amplitude
Does Clampor circuit change the peak-to-peak (i.e., rms value)? Justfy
Q3 Draw the equivalent circuit of a DC Motor, Separated Excited DC Motor and Compounded DC Motor. Label each component properly (a)
A four-pole induction motor drives a load at 2575 rpm. This is to be accomplished by using an electronic converter to convert a 400-V dc source into a set of three-phase ac voltages. ▾ Part A Find the frequency required for the ac voltages assuming that the slip is 4 percent. The load requires 2 hp. Express your answer to three significant figures and include the appropriate units. f= Submit ▾ Part B Value μÀ Submit I= Value Provide Feedback ^ Request Answer If the dc-to-ac converter has a power efficiency of 85 percent and the motor has a power efficiency of 80 percent, estimate the current taken from the dc source. Express your answer to three significant figures and include the appropriate units. 4 Ò Request Answer Units ? Units ?
An overexcited Synchronous motor at no-load means that the PF angle is equal to: Select one: a. 45º leading b. 0º leading c. 90º leading d. 45º lagging e. 90º lagging
4) A 40-kW induction motor, with a lagging power factor of 0.76 is supplied by a 120-Vrms, 60-Hz sinusoidal voltage source. Find the capacitance needed in parallel with the motor to raise the power factor to 0.9 lagging

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS