A 25-ft crane supported at its lower end by a pin is elevated by a horizontal cable. A 250-lb load is suspended through the cable. The center of gravity of the crane is 10 ft from the pin, and the crane weighs 200 lb. Hint: You don't have to convert the unit since they cancel out on both sides. Т 25. Find the tension in the cable. 26. Find the total force acting on the pin. y

A 25-ft crane supported at its lower end by a pin is elevated by a horizontal cable. A 250-lb load is suspended through the cable. The center of gravity of the crane is 10 ft from the pin, and the crane weighs 200 lb. Hint: You don't have to convert the unit since they cancel out on both sides. Т 25. Find the tension in the cable. 26. Find the total force acting on the pin. y

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter9: Statics And Torque

Section: Chapter Questions

Problem 11PE: (a) What force must be exerted by the wind to support a 2.50-kg chicken in the position shown in...

See similar textbooks

Similar questions

(a) What force must be exerted by the wind to support a 2.50-kg chicken in the position shown in Figure 9.33? (b) What is the ratio of this force to the chicken's weight? (c) Does this support the contention that the chicken has a relatively stable construction? Figure 9.33
After an unfortunate accident occurred at a local warehouse, you were contracted to determine the cause. A jib crane collapsed and injured a worker. An image of this type of crane is shown in the figure.The horizontal steel beam had a mass of 85.10 kg per meter of length, and the tension in the cable was ?=11910 N . The crane was rated for a maximum load of 500 kg . If ?=5.580 m , ?=0.558 m , ?=1.900 m , and ℎ=2.160 m , what was the magnitude of ?L (the load on the crane) before the collapse? The acceleration due to gravity is ?=9.810 m/s2 .
After an unfortunate accident occurred at a local warehouse, you were contracted to determine the cause. A jib crane collapsed and injured a worker. An image of this type of crane is shown in the figure.The horizontal steel beam had a mass of 83.40 kg per meter of length, and the tension in the cable was ?=11130 N. The crane was rated for a maximum load of 500 kg. If ?=6.160 m, ?=0.450 m, ?=1.300 m, and ℎ=1.890 m, what was the magnitude of ?L (the load on the crane) before the collapse? The acceleration due to gravity is ?=9.810 m/s2. ?L= What was the magnitude of force ?P at the attachment point P? Fp=
After an unfortunate accident occurred at a local warehouse, you were contracted to determine the cause. A jib crane collapsed and injured a worker. An image of this type of crane is shown in the figure.The horizontal steel beam had a mass of h 81.70 kg per meter of length, and the tension in the cable was T = 12170 N. The crane was rated for a maximum load of 500 kg. If d = 5.000 m, s = 0.450 m, x = 1.350 m, and h = 2.160 m, what was the magnitude of W, (the load on the crane) before the collapse? The acceleration due to gravity is g = 9.810 m/s². W WL = N What was the magnitude of force Fp at the attachment point P? Fp = N * TOOLS х10'
After an unfortunate accident occurred at a local warehouse, you were contracted to determine the cause. A jib crane collapsed and injured a worker. An image of this type of crane is shown in the figure.The horizontal steel beam had a mass of 85.10 kg per meter of length, and the tension in the cable was T=12170 N. The crane was rated for a maximum load of 500 kg500 kg. If d=5.000 m, s=0.522 m, x=1.400 m, and h=2.160 m, what was the magnitude of ?LWL (the load on the crane) before the collapse? The acceleration due to gravity is g=9.810⁢ m/s2. WL= ____ N ? What was the magnitude of force Fp at the attachment point P? Fp____N ?
After an unfortunate accident occurred at a local warehouse, you were contracted to determine the cause. A jib crane collapsed and injured a worker. An image of this type of crane is shown in the figure.The horizontal steel beam had a mass of 88.50 kg per meter of length, and the tension in the cable was T = 12560 N. The crane was rated for a maximum load of P 500 kg. If d = 5.000 m, s = 0.558 m, x = 1.050 m, and h = 1.980 m, what was the magnitude of W1 (the load on the crane) before the collapse? The acceleration due to gravity is g = 9.810 m/s². 444.23 Wi = N Incorrect What was the magnitude of force Fp at the attachment point P? Fp = N
After an unfortunate accident occurred at a local warehouse, you were contracted to determine the cause. A jib crane collapsed and injured a worker. An image of this type of crane is shown in the figure.The horizontal steel beam had a mass of 80.00 kg per meter of length, and the tension in the cable was P T = 12690 N. The crane was rated for a maximum load of 500 kg. If d : 5.870 m, s = 0.522 m, x = 1.600 m, and h = 1.980 m, what was the magnitude of WL (the load on the X crane) before the collapse? The acceleration due to gravity is g : 9.810 m/s?. WL WL = N What was the magnitude of force Fp at the attachment point P? Fp N
The following forces are acting on the bracket below. The bracket has a width w of 2 inches and a height h of 3 inches. The bracket is in equilibrium (not accelerating). Determine F3y knowing F1x-98 lbf and F1y=195 lbf. For this question, what is F3.y in Ibf? Note that the y- direction is pointing up, so if the force is pushing down on the bracket, it has a negative magnitude. 39
After an unfortunate accident occurred at a local warehouse, you were contracted to determine the cause. A jib crane collapsed and injured a worker. An image of this type of crane is shown in the figure.The horizontal steel beam had a mass of h 80.00 kg per meter of length, and the tension in the cable was T = 12170 N. The crane was rated for a maximum load of d 500 kg. If d 5.580 m, s = 0.522 m, x = 1.850 m, and h = 1.890 m, what was the magnitude of WL (the load on the crane) before the collapse? The acceleration due to gravity is g = 9.810 m/s². WL WL = N What was the magnitude of force Fp at the attachment point P? Fp N
How to solve this? The boom of the wall crane 4m long is held at right angles to the wall by a wire that is attached to the wall 3m above the foot of the boom. If the load lifted is 45000N, find the tension in the wire and the compression force in the boom Neglect the weight of the boom.
After an unfortunate accident occurred at a local warehouse, you were contracted to determine the cause. A jib crane collapsed and injured a worker. An image of this type of crane is shown in the figure.The horizontal steel beam had a mass of 86.80 kg per meter of length, and the P. tension in the cable was T = 12560 N. The crane was rated for a maximum load of 500 kg. If d = 5.870 m, s = 0.522 m, x = 1.650 m, and h = 2.250 m, what was the magnitude of W (the load on the crane) before the collapse? The acceleration due to gravity WL is g = 9.810 m/s². %3D WL = What was the magnitude of force Fp at the attachment point P?
A 5 N uniform wooden plank is supported by two posts that are 1.2 m apart. A 4 N load is hung 0.3 m from one post. Find the magnitude of the force exerted by each post. 0.3 m +4 N 5 N 1.2 m