show our complete solutionWhat is the computed molar concentration of EDTA? ProblemA 3.75-g sample of calcium carbonate was dissolvedusing 6 M HCI, and diluted with water to 500 mL. A 50.00-mL portion of this solution is transferred to a flask and thepH was adjusted by adding 5mL of NH3-NH,CI buffer.After adding EBT indicator, the solution required 47 mLEDTA to reach the end point.

Answered: Image /qna-images/answer/890e588c-ade1-424e-9224-7721909809f3.jpg

A 3.75-g sample of calcium carbonate was dissolve using 6 M HCI, and diluted with water to 500 mL. A 50.0C ml portion of this solution is transferred to a flask and the pH was adjusted by adding 5mL of NH3-NH,CI buffe After adding EBT indicator, the solution required 47 m EDTA to reach the end point.

A 3.75-g sample of calcium carbonate was dissolve using 6 M HCI, and diluted with water to 500 mL. A 50.0C ml portion of this solution is transferred to a flask and the pH was adjusted by adding 5mL of NH3-NH,CI buffe After adding EBT indicator, the solution required 47 m EDTA to reach the end point.

Chemistry: An Atoms First Approach

2nd Edition

ISBN:9781305079243

Author:Steven S. Zumdahl, Susan A. Zumdahl

Publisher:Steven S. Zumdahl, Susan A. Zumdahl

Chapter14: Acid- Base Equilibria

Section: Chapter Questions

Problem 120IP: A 10.00-g sample of the ionic compound NaA, where A is the anion of a weak acid, was dissolved in...

See similar textbooks

Similar questions

A 10.00-g sample of the ionic compound NaA, where A is the anion of a weak acid, was dissolved in enough water to make 100.0 mL of solution and was then titrated with 0.100 M HCl. After 500.0 mL HCl was added, the pH was 5.00. The experimenter found that 1.00 L of 0.100 M HCl was required to reach the stoichiometric point of the titration. a. What is the molar mass of NaA? b. Calculate the pH of the solution at the stoichiometric point of the titration.
A buffer is prepared by dissolving 0.062 mol of sodium fluoride in 127 mL of 0.0399 M hydrofluoric acid. Assume no volume change after NaF is added. Calculate the pH of this buffer.
A buffer solution contains 0.487 M CH,NH,Cl and 0.252 M CH,NH, (methylamine). D the pH change when 0.058 mol KOH is udded to 1.00 Lof the buffer. etemine pH ater addition - pli before addition- pH change-( Submit Answer Retry Entire Group more group attempts remaining Determine the pHi change when 0.080 mol HCIO, is added to 1.00 Lof a buffer solution that is 0.340 M in CH,COOH and 0.283 M in CH,COO". pH after addition - pH before addition pl change -[ Submit Answer Retry Entire Group 9 more group attempts remaining
← The Demon of Bell Witch Ca x B Monthly book subscription | Calendar с Disney+ | Movies... session.masteringchemistry.com/myct/itemView?assignment ProblemID=192025012&attemptNo=1&offset=next inquizitive
Determine the pH at the point in the titration of 40.0 mL of 0.200 M H2NNH2 with 0.100 M HNO3 after 80.0 mL of the strong acid has been added. The value of Kb for H2NNH, is 3.0 x 10-6. ( PREV 1 2 3 4 NEXT > Based on the result of the acid-base reaction, set up the ICE table in order to determine the unknown. H2NNH3*(aq) + H20(1) - H;O*(aq) + H,NNH2(aq) Initial (M) Change (M) Equilibriu m (M). 5 RESET 0.100 0.200 0.0333 0.0667 +x -x 0.100 + x 0.100 - x 0.200 + x 0.200 - x 0.0333 + x 0.0333 - x 0.0667 + x 0.0667 - x
B? The concentrations of acid and base in buffer B are twice the concentrations of buffer A (buffer B is twice as strong as buffer A). Show that the ratio of the volume of titrant required to raise the pH of each buffer 1 unit (VB/VA) is directly related to the ratio of the buffer strengths (strengthe/strengthA) be Buffer capuaty (defined ar Me auoler of naud ar Hhe nuolet ofaud or have needed to change the uubon hu 1 unuf / hy the pH change and voturme huffer ucd in hbres of
Exercise 18.50 MISSED THIS? Read Section 18.2 (Pages 788 - 799) ; Watch KCV 18.2B, IWES 18.2, 18.3. %3D For each of the following solutions, calculate the initial pH and the final pH after adding 0.0200 mol of NaOH.
A buffer solution contains 0.248 M KH2PO4 and 0.482 M Na2HPO4.If 0.0383 moles of hydrobromic acid are added to 225 mL of this buffer, what is the pH of the resulting solution ? Please type answer not write by hend
CuFrent Attempt in PPogress A buffer is prepared by mixing 48.9 g of NH3 and 48.9 g of NH,Cl in 0.683 L of solution. What is the pH of this buffer, and what will the pH change to if 7.68 g of HCI is then added to the mixture? Your answer is correct. pH of this buffer= 9.62 Hint Your answer is incorrect. The pH change = i (in case of decreasing pH the answer should be negative). Hint MacBook Air
3. What is the pH of a buffer composed of 0.35 M H;PO4¯(aq) and 0.65 M HPO4?- (aq)? (Ka of H2PO4¯ is 6.2 × 10-8) a) 7.48 b) 9.06 c) 6.94 d) 7.73 e) 7.21 f) none of the above 1(CH CU O U corhon
← The Demon of Bell Witch Ca x B Monthly book subscription | Calendar с Disney+ | Movies... session.masteringchemistry.com/myct/itemView?assignment ProblemID=192025013&attemptNo=1&offset=next
Calculate pBa2* when 25.00 mL of 0.100 M is titrated with 25.00 mL of 0.100 M Ba2. Kp 1.1 x 10 10 for BaSO4. A) 9.96 B) 7.14 C) 4.98 D) 1.30 E) 1.00 O A O B