A 42 meter solid shaft is under torsional loading 53 Nm. If in this application, the allowable shear stress for the material is 369 MPa. Calculate the required minimum diameter of the shaft: _____ mm ( input the value directly from your calculation before rounding it up to an engineering accepted diameter)Pay attention to units, and calculate your answer to one decimal place. A 42 meter solid shaft is under torsional loading 53 Nm. If in this application, the allowable shear stress for the material is 369 MPa.TCalculate the required minimum diameter of the shaft:accepted diameter)mm (input the value directly from your calculation before rounding it up to an engineeringPay attention to units, and calculate your answer to one decimal place.

Given: Torsional loading, T = 53N-m Allowable shear stress = 369MPa Required: Minimum diameter of…

A 42 meter solid shaft is under torsional loading 53 Nm. If in this application, the allowable shear stress for the material is 369 MPa. T T Calculate the required minimum diameter of the shaft: accepted diameter) mm (input the value directly from your calculation before rounding it up to an engineering

A 42 meter solid shaft is under torsional loading 53 Nm. If in this application, the allowable shear stress for the material is 369 MPa. T T Calculate the required minimum diameter of the shaft: accepted diameter) mm (input the value directly from your calculation before rounding it up to an engineering

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.3P: A tensile test was performed on a metal specimen having a circular cross section with a diameter 0....

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
y 400 mm 4 mm B 200 mm A 6 mm The rectangular plate is subjected to the deformation shown by the dashed line. Determine the average shear stress in the plate if the shear modulus of the material is 2 MPa. Express your answer in kPa and round it to the nearest integer if necessary.
2. Shown below are pieces of unsaid material. They are combined and locked in each other and a force P is pulling each side. Assuming that the Shear stress for the material is 38 MPa, Determine the force P needed to fracture the materials in shear. 30 mm 30 mm 80 mm Section A-A
A load P is applied to a steel component which is supported an aluminum plate into which a 12 mm diameter hole has been drilled. Knowing that the maximum allowable shearing stress is 86.5 MPa in the steel and 160 MPa in the aluminum plate, determine the largest load which may be applied to the steel component. Provide your answer in kN with precision to two decimal points. 10 mm Answer: 12 mm 40 mm P 8 mm
1.5-7 The data shown in the table were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2 in.² in area and a gage length (the length over which the elongation is measured) of 2.000 inches. d. Estimate the value of the proportional limit. e. Use the 0.2% offset method to determine the yield stress. Load (kips) 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 ܩܙ ܘ 5.5 6.0 6.5 Elongation × 10³ (in.) 0 0.160 0.352 0.706 1.012 1.434 1.712 1.986 2.286 2.612 2.938 3.274 3.632 3.976 Load (kips) 7.0 7.5 8.0 8.5 9.0 9.5 10.0 10.5 11.0 11.5 12.0 12.5 13 Elongation × 10³ (in.) 4.386 4.640 4.988 5.432 5.862 6.362 7.304 8.072 9.044 11.310 14.120 20.044 29.106
A compound bar consists of (4) aluminum alloy bars of (2mm) diameter and (2) steel bars of (3mm) diameter. Determine the followings: 1- The stresses in each material when a compressive force of 70 kN is applied on the compound bar and the temperature is changed from 20 °C to 40 °C. 2- The compound modulus of elasticity (Ec). Knowing that : E=200GN/m² E=70 GN/m² and a=11×10% per °C and a=22×10 per °C for Steel for Aluminum Alloy
1.3 (A). Define the terms shear stress and shear strain, illustrating your answer by means of a simple sketch. Two circuiar bars, one of brass and the other of steel, are to be loaded by a shear load of 30kN. Determine the necessary diameter of the bars (a) in single shear, (b) in double shear, if the shear stress in the two materials must not exceed 50 MN/m² and 100 MN/m? respectively. [27.6, 19.5, 19.5, 13.8 mm.]
A steel rod with a cross sectional area of 120 [mm] ^2 is stretched between two fixed points. The tensile load at 20°C is 4200N. What will be the stress at-25°C? a=11.7x (10] ^(-6)/°C and E = 200GPA. See figure 06. * Figure 06 L Ti
Shown is a composite plate joined together by rivets. The components consist of two tension bar plates that is ¾ X 4 inch and riveted together by two splice plates which is 0.8 X 6 inch. Each rivet has a diameter of 25.4 mm. Considering that the allowable stress for the tension bar plates and splice plates is σ=20.0 ksi, the allowable shear stress for the rivets is σ=25.0 ksi and the allowable bearing stress on the rivets and splice plates is σ=25.0 ksi. What will be the maximum permissible load P such that none of the allowable stresses will be exceeded?
2. A steel bar, whose cross section is 0.55 inch by 4.05 inches, was tested in tension. An axial load of P = 30,500 lb. produced a deformation of 0.105 inch over a gauge length of 2.05 inches and a decrease of 0.0075 inch in the 0.55-inch thickness of the bar. * Determine the lateral strain. Your answer Determine the axial strain. Your answer Determine the Poisson's rati v. Your answer Determine the decrease in the 4.05-in. cross-sectional dimension (in inches). * Your answer
Shown is a copper bar which has a diameter of 10 mm and loaded by tensile loadP = 0.0137 MN The maximum shear stress in the bar is approximately: Match each item to a choice: Tmax