A bar having two cross sectional areas is loaded by an axial force (P). Part AB and BC are circular with diameters 50 mm and 38 mm, respectively. If the stress in AB is 40 MPa, what is the stress in BC?

A bar having two cross sectional areas is loaded by an axial force (P). Part AB and BC are circular with diameters 50 mm and 38 mm, respectively. If the stress in AB is 40 MPa, what is the stress in BC?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.7.7P: A bar of monel metal with a length L = 9 in. and a diameter d = 0225 in. is loaded axially by a...

See similar textbooks

Related questions

Q: A uniformly distributed force of C kN/m and a concentrated load of D kN are applied to a cantilever…

Q: A uniform bar 3.00 m long is held by ropes at the ends making angle 60.0 and 30.0, respectively,…

A: Let us consider, Tension in rope of left end =T1 Tension in rope of right end = T2 Weight of bar =…

Q: The L-bar shown in the figure is fastened by a bearing at point A that allows it to rotate, such…

A: Given F=800NRBmax=600N

Q: A steel bar of cross-sectional area 200 mm^2 is loaded as shown in Fig. Find the change in length of…

A: For solution refer below images.

Q: The cantilever truss in the figure is hinged at D and E. Find the force in member AC. 1000 Ib 60 60•…

Q: A cylinder head of a steam engine is held on by 14 bolts. The effective diameter of the cylinder is…

Q: D A 10kN 28kN + → 60KN 44KN + 120cm 80cm Ост 40cm Figure 1 a) Draw a Free Body Diagram for each…

Q: Example 18. The homogeneous bar AB of 300 N is resting as shown in figure Ex.18. Assuming contact…

Q: Q: A rigid block of negligible mass is supported by three rods as shown in figure, if a load (P) is…

Q: Q2) Layers of Brass, Steel and Aluminum are bonded together and formed section shown below.…

Q: A plane frame with a pin support at A androller supports at C and E has a cable attached at E,which…

A: Cable force F=400NAB=4mBC=3mCD=4mCE=5m To-Find:- (a) Find reactions at supports A, C, and E. (b)…

Q: Home Work :- A hydraulic cylinder as show in the figure is subjected to a compressive force (F) at…

Q: Find the stress in members DF, FI, and HI if the cross- sectional area of each member is 800 mm².…

Q: Two bars are connected to a rigid plate as shown. If L = 15 kips, M = 9 kips, N = 9 kips, and O = 33…

Q: * A rigid bar AB is hinged at A and supported by copper rod 2 m long and steel rod i m long as shown…

Q: Figure Q2 shows a shaft consists of Rods AB, BC and CD which made of Aluminium, Brass and Steel,…

Q: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure.…

A: Answer: (1) Considering steel : P = 12600 N. (2) Considering aluminum : P = 30400 N. (3) Considering…

Q: A rectangular (3" x 5") rod has an axial (tension) load applied, P, of 300,000 lbs. The diameter of…

Q: 1- the upper part in fig below is a steel and lower part is a cast iron , the load P shortens the…

Q: ka 2 ki P Rigid bar k3 for the system shown in the figure, which of the following statements are…

A: from the figure , we see that , point 1,2,3,4 are rigid on the wall , so they can't move while…

Q: a) Figure Q2a shows a hollow tube of rectangular cross-section subjected to an axial compressive…

Q: 3. A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

Q: A brass rod (E 110 GPa) with cross sectional area of 250 mm2 is loaded by forces P =15 kN, P2 =10…

A: GIVEN DATA- E=110GPa A=250mm2 P1=15KN P2=10KN P3=8KN WE HAVE TO FIND CHANGE IN LENGTH OF BAR

Q: In the figure, AB is a rigid rod and CB is a cable. If M is 900kg, what is the pin reaction at A on…

A: To find: The pin reaction at A on the rod and the tension in the cable. Given: The AB is rigid rod…

Q: Two rods support the rigid bar ABC as shown in the figure. A downwards load P of 50 kN is applied at…

A: Given:P=50 KNFor BD:L=600 mmE=73 GPaA=1250 mm2For CE:L=400 mmE=200 GPaA=750 mm2

Q: A flat plate with a central hole is subjected to an axial tensile force F of 12 KN, as shown in the…

A: Given Data : Force F = 12 KN Tensile Stress Syt = 70 N/mm2 width w = 8cm diameter d = 4 cm radius r…

Q: Q2) Find the stress in steel rods BD and CE as shown in Figure due to the applied load 4 kN and the…

Q: QI : In the following fig the truss is loaded by a force (P) at point ( G) and ( 2p) at point (F)…

A: Note:As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: Figure Q2 shows a shaft consists of Rods AB, BC and CD which made of Aluminium, Brass and Steel,…

Q: 1. The homogeneous bar shown in Fig. P-106 is supported by a smooth pin at C and a cable that runs…

A: Given Weight, W = 40 kN Diameter, d = 25 mm = 0.025 m Length, AB = 4 m…

Q: A frame structure is shown in the following Figure. Members ABC and BD are pin jointed to supports…

Q: Question 2 a) Figure Q2a shows a hollow tube of rectangular cross-section subjected to an axial…

Q: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in figure. Axial…

Q: The diameter of a piston of the steam engine is 300 mm and the maximum steam pressure is 0.7 N/mm2.…

A: Given:Diameter of piston,DPISTON=300mmPSTEAM=0.7Nmm2Compressive stress,σ=40Nmm2Net force by piston…

Q: A wire 4m long is stretched horizontally between points A and B 4m apart. A load W placed at the…

A: Given data Length of the Stretched wire = 4 mArea of cross-section of wire = 25 mm2Young's Modulus =…

Q: A steel bar is heated from room temperature to 80°C while it is free to expand. The bar will…

Q: 1. A force P = 27 kN acts on a round bar with d = 50 mm, find the stress in KPa. 2. The piston rod…

A: Answer: 1. The stress is 13751 kPa. 2. The compression of the piston rod is 0.0261 mm.

Q: Find the stress in ksi developed in the pipe due to a temperature rise of 83 degrees F.

A: Length of the pipe is L=12 ft Temperature rise in the pipe is ∆T=83 °F Modulus of elasticity of the…

Q: In the system in the figure, two rods carry the P force. a) Since the maximum stress that the rods…

Q: Q1A 30 cm square steel bearing plate lies between a 20 cm diameter wooden post and a concrete…

A: According to the given information:…

Q: A weight W is supported by an eyebar AC and a horizontal strut BC. The eyebar and the strut are pin…

A: we will make FBD of joint C, which will provide us the necessary force in eyebar. thereafter, we can…

Q: An electric pole design is shown below. The frame is used to carry high-voltage wires. If b=600 mm,…

Q: A weight of 500N is supported by two metallic ropes as shown in the figure. The values of tensions…

Q: For the rigid beam , find stresses in the two suspended rods to the applied load and an in change in…

Q: 8. A prismatic bar AB of length 6m and weight 3 KN is hinged to a wall and supported by a cable BC.…

A: Given Data:*AB=6m*weight w=3 KNTo finda)Hinge reaction Ax=? Ay=?b)tension oin BC, T=?

Q: B. 1.20m w.S. 6.0m

Q: 2. The tank shown in the figure is fabricated from 10mm steel plate. Determine the maximum…

A: As per our guidelines we are supposed to answer only one question. Kindly repost other questions as…

Q: The maximum break stress of the chain ring seen in the figure on the side is 420 N/mm2, since the…

A: Normal stress is defined as the intensity of force exerted over a unit cross-sectional area. The…

Q: ven m-50kg and the following dimensions: AB = 1m, BC 3m, angle ACD 30 degrees Draw a free body…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A single steel strut AB with a diameter (a) Find the strut force Fs and average normal stress ds= 8 mm supports the vehicle engine hood of a in the strut. mass 20 kg that pivots about hinges at C and D (see (b) Find the average shear stress t aver in the bolt at A,figure parts a and b). The strut is bent into a loop at (C) Find the average bearing stress bon the bolt at A. its end and then attached to a bolt at A with a diameter db= 10 mm. Strut AB lies in a vertical plane.
,3-23 A 200-lb trap door (AD) is supported by a strut (BC) which is pin connected to the door at B (see figure). (a) Find reactions at supports A and C. (b) Find internal stress resultants N, V, and M on the trap door at 20 in. from A.
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A round bar of 10 mm diameter is made of aluminum alloy 7075-T6 (see figure). When the bar is stretched by axial forces P, its diameter decreases by 0.0 16 mm. Find the magnitude of the load P. Obtain the material properties from Appendix 1.
A flat bar of width b and thickness t has a hole of diameter d drilled through it (see figure). The hole may have any diameter that will fit within the bar. What is the maximum permissible tensile load Pmaxif the allowable tensile stress in the material is st?
Two bars AC and BC of the same material support a vertical load P (see figure). The length L of the horizontal bar is fixed, but the angle fl can be varied by moving support A vertically and changing the length of bar AC to correspond with the new position of support A. The allowable stresses in the bars are the same in tension and compression. When the angle ft is reduced, bar AC becomes shorter, but the cross-sectional areas of both bars increase because the axial forces are larger. The opposite effects occur if the angle 0 is increased. Thus, the weight of the structure (which is proportional to the volume) depends upon the angle ft. Determine the angle ft so that the structure has minimum weight without exceeding the allowable stresses in the bars. Note: The weights of the bars are very small compared to the force P and may be disregarded.
A plane Frame with pin supports at A and E has a cable attached at C, which runs over a friction-less pulley at F(see figure). The cable Force is known to be 500 lb. (a) Find reactions at supports A and E. (b) Find internal stress resultants N, V, and M at point H.
A long, slender bar in the shape of a right circular cone with length L and base diameter d hangs vertically under the action of its own weight (see figure). The weight of the cone is W and the modulus of elasticity of the material is E. Derive a formula for the increase S in the length of the bar due to its own weight. (Assume that the angle of taper of the cone is small.)
Solve the preceding problem if the axial stress in the middle region is 24,000 psi, the length is 30 in., and the modulus of elasticity is 30 × 106 psi. In part (c), assume that dmax = 0.02 in
A mountain bike is moving along a flat path at constant velocity. At some instant, the rider (weight = 670 N) applies pedal and hand forces, as shown in the figure part a. (a) Find reaction forces at the front and rear hubs. (Assume that the bike is pin supported at the rear hub and roller supported at the front hub.) (b) Find internal stress resultants N, V, and M in the inclined seat post (see figure part b
A vertical bar is loaded with axial loads at points B, C, and D. as shown in the figure. The bar is made of steel with a modulus of elasticity E = 29,000 ksi., The bar has a cross-sectional area of 8.24 in2. Calculate the displacements at points B, C, and D. Ignore the weight of the bar
A plane frame is restrained al joints A and C, as shown in the figure. Members AB and BC are pin connected at B. A triangularly distributed lateral load with a peak intensity or 90 lb/ft acts on AB. A concentrated moment is applied at joint C. (a) Find reactions at supports A and C. (b) Find internal stress resultants A', V, and \f at x = 3 ft on column AB.