A bar with a right angle bend is supported by a collar A on smooth square rod, and by a roller at B. The forces and geometry are as shown in the figure and parameter table. Determine all the support reactions. Define all vector quantities to be positive in the positive coordinate axes directions. |A F1 F3 F2 parameter value units 2.5 L2 1 La 2 m F 350 450 F3 300 B. E E EZzz

A bar with a right angle bend is supported by a collar A on smooth square rod, and by a roller at B. The forces and geometry are as shown in the figure and parameter table. Determine all the support reactions. Define all vector quantities to be positive in the positive coordinate axes directions. |A F1 F3 F2 parameter value units 2.5 L2 1 La 2 m F 350 450 F3 300 B. E E EZzz

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter4: Shear Forces And Bending Moments

Section: Chapter Questions

Problem 4.3.25P: Frame ABC has a moment release just left of joint B. Find axial force N, shear force V, and moment M...

See similar textbooks

Similar questions

The inclined beam represents a ladder with the Following applied loads: the weight (W) of the house painter and the distributed weight (u) of the ladder itself. Find support reactions at A and B: then plot axial force (N), shear (V), and moment (M) diagrams. Label all critical N, V, and M values and also the distance to points where any critical ordmates are zero. Plot N, V, and M diagrams normal to the inclined ladder. Repeat part (a) for the case of the ladder suspended from a pin at B and traveling on a roller support perpendicular to the floor at A.
Solve the preceding problem for the following data: b = 6 in., b = 10 in, L = 110 ft, tan a = 1/3, and q = 325 lb/ft.
Repeat Problem 6.4-14 but use the configuration of channel shapes and loading shown in the figure. Use P = 250 N.
Find support reactions at 4 and Band then use the method of joints to find all member forces. Let b = 3 m and P = 80 kN.
Repeat 1.3-9 but use the method of sections go find member forces in AC and BD.
A cargo ship is tied down to marine boll arts at a number of points along its length while its cargo is unloaded by a container handling crane. Each bollard is fastened to the wharf using anchor bolts. Three cables having known tension force magnitudes F, = ll0 kN.F, = 85kN.and F, 9OkNare secured to one bollard at a point A with coordinates (0.0.45 m. 0) in the x-r-: coordinate system shown in the figure part b. Each cable force is directed at an attachment point on the ship. Force F, is directed from point A to a point on the ship having coordinates (3 m, 9 m. 0) force F, is directed at a point with coordinates (6.5 m. 8.5 m. 2 m) and force F, is directed at a point with coordinates (8 m. 9 m. S m). The diameter of each anchor bolts is 4 24 mm. (a) Find the reaction forces and reaction moments at the base of the bollard. (b) Calculate the average shear stress in the anchor bolts (in the x-: plane). Assume each bolt cart ics an equal share of the total force.
A sign of weight W is supported at its base by four bolls anchored in a concrete footing. Wind pressure P acts normal to the surface of the sign; the resultant of the uniform wind pressure is force fat the center of pressure (C.P). The wind force is assumed to create equal shear forces F/4 in the y direction at each boll (see figure parts a and c). The overturning effect of the wind force also causes an uplift force R at bolts A and C and a downward force (— R) al bolts B and D (see figure part b). The resulting effects of the wind and the associated ultimate stresses for each stress condition are normal stress in each boll (h — 60 ksi); shear through the base plate (th = 17 ksi); horizontal shear and bearing on each bolt ( tfur = 25 ksi and cr^ = 75 ksi): and bearing on the bottom washer at B (or D) (abor = 50 ksi).
Repeat Problem 9,5-15 for the anti-symmetric loading shown in the figure.
A polyethylene tube (length L) has a cap that when installed compresses a spring (with under-formed length L1) by an amount ?? = (L1 = L). Ignore deformations of the cap and base. Use the force at the base of the spring as the redundant. Use numerical properties given in the boxes. (a) What is the resulting Force-in the spring, Fk? (b) What is the resulting Force in the tube, Ftl (c) What is the filial length of the tube, Lf? (d) What temperature change ?T inside the tube will result in zero force in the spring
A bar with a right angle bend is supported by a collar A on smooth square rod, and by a roller at B. The forces and geometry are as shown in the figure and parameter table. Determine all the support reactions. Define all vector quantities to be positive in the positive coordinate axes directions. B |A F, F3 F2 parameter value units 2.5 m L2 L3 F1 F2 F3 1 2 350 450 N 300 N A, = N Ay = N B = (Мл), N-m (MA), = N-m (MA): N-m E E E
The figure below depicts the tire, axle, and gear of a large tractor. The entire structure is in mechanical equilibrium. Bearings support the rotating axle at points A and C attached to the tractor's frame. A force FD = 5000 lb is applied in the -z direction at point G of a gear with a 3-in radius. The force W = 1000 lb in the +z direction represents a normal force resulting from the weight of the tractor. The force Q acting in the +x direction, represents the traction force between the tire and the ground. The wheel, axle, and gear assembly weigh 150 lb with center of gravity at point D, which lies on the y axis with coordinate yp = -18 in. Points A, C, D (not seen in the figure), and E lie in the yz plane. Point G lies in the xy plane. Questions & Analysis: (a) Draw the FBD for the wheel, axle, and gear assembly if the bearings at A and B resist moments and the bearing at A is a thrust bearing. Label all unknowns. (b) Is the assembly statically determinate or statically…
Problem 4.61 Figure 15m 0.5m B 2.5 m 1 of 1 Part A Determine the magnitude of the moment of the force F = {50i- 21 j-80k} N about the base line AB of the tripod. (Figure 1) Express your answer to three significant figures and include the appropriate units. MAB= Submit μÀ Value Request Answer < Return to Assignment Units Provide Feedback ?