A block is positioned on a 40° slope as shown, and a spring is attached to it as shown. The spring is relaxed (unstretched) in the position shown. The block is given an initial velocity V₁ = 6 m/s downslope. Find the distance "d" that the block will slide before it comes to a stop. Use the Principle of Work and Energy.

A block is positioned on a 40° slope as shown, and a spring is attached to it as shown. The spring is relaxed (unstretched) in the position shown. The block is given an initial velocity V₁ = 6 m/s downslope. Find the distance "d" that the block will slide before it comes to a stop. Use the Principle of Work and Energy.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

We have proper units for the acceleration and tension. The numbers do not tell much if we can trust the results, but we may consider an extreme case when m, = 0, then a = 9.8 m/s T= N. Correct. If m2 = 0, then a = 0 also correct. Two masses m, and m, are connected by a light string that passes over a H.W تحو eap frictionless pulley, as in Figure. Determine the tension in the string, a) b) the acceleration of each object, c) the force that the ceiling exerts on the hook 一 SOLUTION: 1. Physics: Newton's laws for two correctes objects. (Atwood machine) 2. Second Newton's law for 2D case for every object
A8.1. VELOCITY ANALYSIS. For the single-degree-of-freedom mechanism shown below, the velocity of the slider is Vs = 10 mm/s to the right. Calculate the direction and magnitude of Wz and wz and Vp. Use instant centers and AVRT. Rpc = 100 mm. %3! %3D B. link 3 ,Bt A O Islider ground link 2
Solve the problem 5 with resulting answer of V=18km/hr and X=50cm
Consider the following diagram. m1=20 kg and m2= 10 kg. The system is being pulled by an applied force of 200 N. directed 50" above the horizontal. The coefficient of kinetic friction between the block and the surface is u-0.2. 50 m, 20kg Coefficient of friction 4=0.2 10 kg. 309 7) Calculate the acceleration of the system. Your answer 8) Calculate the magnitude of the Tension on the rope. Your answer N 00
State the equation that mathematically represents the system. All in domain X(s) hint: there are 3 equations 4:00-1-1-1-1!1! k₁ 0000 0000 B₂ B₁. m₁ 0000 k3 without friction x1 (1) m2 B3 -f(t) + - X2 (1)
The 50 kg block shown in the figure is set in motion without an initial velocity when x₀=150 mm and t=0. Find displacement x when t=0.5 s bytaking,a) c=200 N s / m.b) c=300 N s / m.
Vrope B. OD f TA ro Vcart Alternate View of Spool (rope not shown) Known values: Ti TA To 0.75 ft 1.2 ft 1.7 ft 1 8 Problem Statement: A large spool rolls without slip on a cart. The cart's speed is 17 ft/s. A rope, which is wrapped around the spool's hub, is being pulled at a speed of 5 ft/s, as depicted. Determine: The angular velocity of the spool: i计 The velocity vector of point G: The velocity vector of point A: i+ Be sure to include units with your answers.
A fireworks shell P fired in a vertical trajectory has acceleration given by ay=-g-k*(v^2). The first term in the relation is weight and the second term is due to drag force. The value of the drag parameter k is constant. At the moment shown in the figure, the velocity of the firework is Vp. Calculate the radius of curvature, normal, tangential and resultant acceleration values for this moment. First image is the wanted values and second image is the image of question. ( OA=140m, AP= 210m, k=0.025m^(-1), Vp=20m/s ). I have been trying to solve this question for so long but i couldn't figure it out. Please solve this question so i can understand how to solve this kind of questions.
Drill pipes of 1000 meter original length which is between top drive drilling motor and bottom hole assembly (HWDP, collar and drill bit) is lowered into the well. The specification of drill pipe is as follows: OD=200 mm, ID=175 mm, E = 50 GPa, G=77.2 GPa weight : drill pipe = 100,000 N , bottom hole assembly = 35,000 N Before the bottom hole assembly touch the rock formation: а) Calculate the reaction force between drill pipe and top drive drilling motor b) Calculate the elongation of drill pipe After the bottom hole assembly rest/touch on the rock formation, the elongation of the drill pipe reduces by half. c) Calculate the reaction force between drill pipe and top drive drilling motor. d) Knowing that the top steel drill pipe rotates through two complete revolutions before the drill bit starts to operate, determine the maximum shearing stress caused in the pipe by torsion.
There is a system including two blocks. (mĄ = 2kg, mg = 8kg) This system starts movement from the rest (block B is going downward). If kinetic coefficient of friction for the surface is 0.4. A) What is the tension in the cable? B) If block B travels 0.7 m downward, what is its velocity? A В 0 = 60° %3D
Problem Solving: ) A car is fraveling at the speed Vo on a Tevel road. After the brakes arc applicd at t- 0, the motion can be approximated by x where x is the distance traveled in mcters and t is the time in scconds. Find: (a) Find the value of Vo (6) Find the distance reguired for the car to straight, %3D 2. --t+ 17t 100 stop.
1. Assuming the velocity of B=0.7 m/s after dropping 480 mm. Complete the following: a. Determine the spring constant such that all conditions mentioned above are met b. Using you value from part a, determine distacne B will drop if lowered slowly Notes: System is initially at rest Spring free length Cylinder mass - 25 kg Cylinder radius = 400 mm Ic cylinder 1.2 kg.m² 2 300 mm A Radius of pulley = 100 mm Ic value for pulley 0.5 kg.m² B10 kg Be