A bronze c86100 cylinder with diameter d2 = 60 mm is nested inside a stainless steel tube with inner diameter of d₁ = 80 mm L = 250 mm and wall thickness of t = 10 mm. The bronze cylinder is 1 mm taller than the stainless steel tube. What is the largest axial load, P, that can be applied without either material yielding? For this problem, use Eb = 103 GPa, Est= σY,br=345 MPa, σy,st = 207 MPa. 193 GPa, A P B L 歌 t BY NO SA 2021 Cathy Zupke The maximum load before yielding is P = KN

A bronze c86100 cylinder with diameter d2 = 60 mm is nested inside a stainless steel tube with inner diameter of d₁ = 80 mm L = 250 mm and wall thickness of t = 10 mm. The bronze cylinder is 1 mm taller than the stainless steel tube. What is the largest axial load, P, that can be applied without either material yielding? For this problem, use Eb = 103 GPa, Est= σY,br=345 MPa, σy,st = 207 MPa. 193 GPa, A P B L 歌 t BY NO SA 2021 Cathy Zupke The maximum load before yielding is P = KN

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.12P: Solve the preceding problem if the diameter is 480 mm, the pressure is 20 MPa, the yield stress in...

See similar textbooks

Question

A bronze c86100 cylinder with diameter d2 = 60 mm is nested
inside a stainless steel tube with inner diameter of d₁ = 80 mm
L = 250 mm and wall thickness of t = 10 mm. The bronze
cylinder is 1 mm taller than the stainless steel tube. What is
the largest axial load, P, that can be applied without either
material yielding?
For this problem, use Eb = 103 GPa, Est=
σY,br=345 MPa, σy,st = 207 MPa.
193 GPa,
A
P
B
L
歌
t
BY NO SA
2021 Cathy Zupke
The maximum load before yielding is P =
KN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
Repeat Problem 2.3-18, but assume that the bar is made of copper alloy. Calculate the displacements SBand Scif P = 50 kips, L = 5 ft = 3/5 in., b1= 2.75 in., b2= 3 in., and E = 16,000 ksi.
A copper alloy pipe with a yield stress aY= 290 MPa. is to carry an axial tensile load P = 1500 kN (see figure part a). Use a factor of safety of 1.8 against yielding. (a) If the thickness t of the pipe is one-eighth of its outer diameter, what is the minimum required outer diameter dmin? (b) Repeat part (a) if the tube has a hole of diameter dt 10 drilled through the entire tube, as shown in the figure part b.
Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and inner diameter of 14.4 in. The strut is made of steel with a modulus elasticity of E = 29,000 ksi. Point load P = 5 kips is applied at B. Calculate the change in length of the circular strut DC. What is the vertical displacement of the rigid bar at point B?
A pinned-end strut of aluminum (E = 10,400 ksi) with a length L = 6 ft is constructed of circular tubing with an outside diameter d = 1 in. (sec figure). The strut must resist an axial load F = 4 kips with a factor of safety n = 2.0 with respect to the critical load. Determine the required thickness t of the tube.
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.
Repeat Problem 11.2-14 using L = 12 ft, ß = 0.25 kips/in., ßRl= 1.5ßL2, and ßR2= 2 ßR1.
Repeat Problem 11.3-9. Use two C 150 × 12.2 steel shapes and assume that E = 205 GPa and L = 6 m.
A pinned-and column of a length L = 2A m is constructed of steel pipe (E = 210GPa) having an inside diameter d1= 60 mm and outside diameter d2= 68 mm (sec figure). A compressive load p = 10 kN acts with eccentricity e = 30 mm. What is the maximum compressive stress max in the column? If the allowable stress in the steel is 50 MPa, what is the maximum permissible length Lmaxof the column?
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
A pinned-end strut of a length L = 5.2 ft is constructed of steel pipe (E = 30 × 103 ksi) having an inside diameter d1= 2.0 in. and outside diameter d2= 2.2 in. (sec figure). A compressive load F = 2.0 kips is applied with eccentricity e = 1.0 in. What is the maximum compressive stress max in the strut? What is the allowable load Pallowif a factor of safety n = 2 with respect to yielding is required? (Assume that the yield stress y of the steel is 42 ksi.)