A car jack uses a single square-thread screw to raise a known load. The major diameter and pitch of the screw and the thrust collar mean diameter are known. Running friction coefficients are estimated. Find: (a) Estimate the efficiency of the jack for raising the load. (b) Estimate the power required to drive the screw at a constant 1 revolution per second. Schematic and Given Data: Load 50 kN

A car jack uses a single square-thread screw to raise a known load. The major diameter and pitch of the screw and the thrust collar mean diameter are known. Running friction coefficients are estimated. Find: (a) Estimate the efficiency of the jack for raising the load. (b) Estimate the power required to drive the screw at a constant 1 revolution per second. Schematic and Given Data: Load 50 kN

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter6: Fasteners

Section: Chapter Questions

Problem 12RQ

See similar textbooks

Similar questions

Calculate the dimensions of the I-section of a connecting rod, stating any assumptions. using the data below: Maximum cylinder pressure = 3.15N/mm² Cylinder bore = 100mm Factor of Safety=6 Crank length 95mm Connecting rod length=380mm Take the constant a=7500.
10/10 find the shear stress in bolt in pin A 60 kN 2. 4 M 3 BOLT DIA 20 MM A 50 kN PIN A 159 MPa 636 MPa 79 MPa O 318 MPa (
In the Bolted Connection shown, find the following by ASD.Specifications:M20 Bolts in standard holes. Nominal hole diameter = 22mmEffective Hole diameter = nominal hole diameter + 2 mmA325 steel boltAssume thread in shear planeFv = 372 MPaProperties of Angle Bar< 125 x 125 x 13 mmA = 3065 mm²x = 36.3 mmy = 36.3 mmFy = 248 MPa , Fu = 410 MPa 1. For angle bars used as bolted tension element connected to another element only on one leg, the effective area Ae = UAn. Where: An = Net area, U = Shear lag factor = 1 – x/L, L= center to center longitudinal distance of extremely located fasteners, X= distance from centroid of angle bar to surface of contact of joined elements. What is the shear lag factor of our angular bar? a. 0.454 b. 0.9 c. 0.838 d. 0.869 2. Considering RUPTURE of angle bar, what is the allowable force P that the connection can handle if allowable RUPTURE stress in net area of angle bar is Fu/2 a. 463.83 kN…
Write the Load–Displacement Equations?
Long, square rod in a long cylinder. Also, what is F22? F12 = F21 = || F22 = i w=D/5 A₁ -A₂ t
Q1:Prepare a full-section assembly drawing of the four fastener assemblies shown in the Figure. Dimension both the clearance and the threaded holes. A top view may be shown if required. Scale 1: 1. .250-20 FHMS .375 HEX BOLT AND NUT THREADED INTO BASE 1.00 ↓ .50 T 2.00 Ø.375 STUD THREADED .312 HEX X 1.25 LG INTO BASE FOR 1.00 IN. CAP SCREW AND WITH HEX NUT AND LOCK WASHER ON SPOTFACE SURFACE PLATE WASHER A 2.00- -2.00 -1.00- BASE 1.00- .25 1.50
Calculate the maximum tensile stress developed in a 1/4-20 bolt (Major dia = 0.2500" and Root dia = 0.1959"), 3" long, and a head height of 0.1875", if it is subjected to a load of 426 lbs.
Question 5 a) Calculate the Pitch diameter for the following thread. Given the measurement over the wires is 0.3130. Show your steps. Is the obtained value being acceptable? Why. b) Why the Pitch Diameter is important. Explain..show schematics Nominal Size, Class Маx Маjor Min Major Max Pitch Diam Min Pitch Diam TPI, Series Diameter Diameter 5/16-18 UNC 2A (Ext) 0.3113 0.3026 0.2752 0.2712
12-16. The height and angle of the drawing table, shown in Figure P12.16, is adjusted by rotating the crank. The crank rotates a screw, moving the nut and altering the L distance. The screw has a %-14 UNF thread. The table is initially configured with L = 9 in. Note: The screw is not constrained to the horizontal 18" 18" 11" Crank FIGURE P12.16 Problems 16, 17, 24. Graphically determine the displacement of the top and bottom edges of the raising table when the crank is rotated 5 revolutions.
M P 1: Y A :s.google.com Q1 * Find the number of bolts M8 1 which made from SAE Grade 4 steel that should be used to provide a clamping force of 60 KN between two components of a machine. Also, specify the required tightening torque. (Hint: assume that cach bolt is limited to be stressed to 65% of its proof strength). 1 Add file Q2 * A flat plate with a central hole is subjected to an axial tensile force F of 9.8 KN, as shown in the figure below. Calculate the minimum thickness t of the plate. Given that the material of the plate can support maximum tensile stress of 75 N.mm, w = 10 cm and d = 3 cm. Thickness =t F 1 Add file Submit Clear form II
Condition #1: A structural support for a machine is subjected to a static compression load of 20 kN. The support is manufactured from a circular rod made from SAE 1040 Hot Rolled steel. Specify suitable diameter for the cross section of the rod based on the basic size. Steel data are available in Table A-10 from the textbook. Condition #2: The same structural support of the basic size determined in Condition 1 is subjected to a tensile load of 15 kN that is repeated several thousand times over the life of the machine. This load is not an addition to the 20 kN. Specify a suitable steel that is suitable to this application based on the basic size determined in Condition #1. Loading of Condition #1 does not apply here. Condition #3: The same structural support from Condition 2 is heated from room temperature of 25°C. The support is placed inside a frame on both ends. There is a total clearance of 0.2 mm between the support and its frame. Initial length of the rod is 200 mm. Specify the…
4 THIS IS HOLLOW- F = 548,000 lb -4.5 OD 3.75" ID # AISI 1020 Steel Tubing OD= OUTSIDE DIAMETER ID INSIDE DIAMETER 548,000 lb O TIMATE A= O= Will it fail?