A composite cantilever beam 2 m long is made core 50 mm wide and 100 mm deep completely enclosed by steel 10 mm thick all around. The steel and aluminum are totally bonded together. If the maximum allowable stress in the aluminum is 60 MPa, determine the maxi- mum allowable concentrated force which the beam can support at the free end and the corresponding maximum deflection. For the aluminum and steel let E = 70 and E. = 210 GPa, respectively.

A composite cantilever beam 2 m long is made core 50 mm wide and 100 mm deep completely enclosed by steel 10 mm thick all around. The steel and aluminum are totally bonded together. If the maximum allowable stress in the aluminum is 60 MPa, determine the maxi- mum allowable concentrated force which the beam can support at the free end and the corresponding maximum deflection. For the aluminum and steel let E = 70 and E. = 210 GPa, respectively.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A composite simply supported beam of span 10m and carrying a point load of 800N at its mid- span, is made of wood (180mm x 180mm) and reinforced with a steel strap (180mm x 20mm) located on its bottom side. Given that: k E,I + E2l2 %3D Determine k and hence the normal stress at points B and C. What is the maximum stress if the reinforcement steel plate is removed? Take Est = 210 GPa and Ew = 15 GPa. 180 180 O. 2 20
A leaf spring 75 cm long is required to carry a central load of 8 kN. If the central deflection is not to exceed 2 cm and bending stress no greater than 200 MPa, determine the thickness, width and number of plates. Also compute the radius to which plates should be curved. As- sume width of plate to be 12 times its thickness and E = 200 GPa.
Picture given below; There is a uniformly distributed load on the beam, which is made of Al2010 (T4) alloy T-profile and is connected to the "A" sliding bearing with "B" joint fixed support. Safe compression and tensile normal stress of the beam is Gemn=100 MPa. q=23 kN/m C-C Kesiti + 15 | 18 | 15 q=23 kN/m A유 30 cm 100 cm 150 cm 16 KİRİŞ T- PROFİLİ 74 Ød MAFSAL PİMİ Ölçüler mm dir. 104 S-1) Calculate the support reactions by drawing the SCD of the beam. S-2) The beam; a) Draw the shear force diagram, b) Moment diagram and determine the maximum moment. S-3) Find the x and y axis coordinates of the center of gravity of the cross-sectional area of the beam whose T-profile dimensions are given. S-4) Find the moments of inertia with respect to the vertical and horizontal axes passing through the center of gravity of the T-profile cross-section area. S-5) Find the tensile and compression stresses caused by bending on the beam with T-profile and check the safe carrying condition of this…
Consider the reinforced cConcrete beam shown. The 250 mm beam is subjected to a positive bending moment of 175 kNm. Determine the stress in the steel and the maximum stress in the concrete. Use E=2.5 GPa for the concrete and 200 GPa for the steel. Use concrete as the reference material. I mm4 O po o SO mum Ost MPa (Ocon)max 4 pcs. MPa 20mmø Please follow this format in answering. Given: Required: n I in mm4 Ost in MPa (O con)max in MPa Solution: (Please answer in detailed (step by step). Indicate labels on what you are doing/performing, for example what formula is used) After the computation, provide an explanation (in words) of how you solve the problem; the step-by-step process that you took, the strategy, etc. W ost
A rigid weightless beam loaded by the moment M is Supported at the point D by the fix ed jant Support and at the points B ond c verticel bars are connected holáing the beom horizontelly, For the data listed below determine: Data: E= 2.{x10%MPa yie ld stress Sy=250Mla , fuctor of sufety Calculate : Allowable moment M ? other data: Is a = 2,5 cm , A = 3,6 cm? *Use factor- safety -design method nd linmit state -design method. Both methods ce Mardatory. I 2 A A.E B M
5. The rigid beam rests on two short posts AC and BD as shown. Post AC is made from steel with E-200 GPa and BD from aluminum with E-70 GPa. The diameters of posts AC and 80 are 25 mm and 40 mm, respectively. Determine the vertical displacement of point on AB 100 KN 400mm D 6. The timber beam has a cross-sectional area of 2000 mm and its modulus of elasticity is 12 GP Axial loads are applied at points B, C, and D as shown. Calculate the total change in length of the beam. Answer: 2.33 mm 40 KN 35 KN 20 KN 3.20 m 1.60m 3.20 m
beam, simply supported at its ends, carries a load which increases uniformly from 15kN/m at the left-hand end to 100 kN/m at the right-hand end. If the beam is 5m long, find the equation for the rate of loading and, using this, to determine the deflection of the beam at mid-span if E= 200GN/m² and I=600*10 m².
Determine the deflection at midspan for the beam of Problem 4–69 using Castigliano's theorem. Material of the beam is steel with E=30 Mpsi. w 180 lbf/in 1.375-in dia. r1.375-in dia. Problem 4-69 11.75-in dia. +3 in + 10 in 3 in
The beam shown is made from 6 × 6 × 1/4 inch rectangular steel structural tubing. If load P = 650 lb is applied, then the magnitude of the deflection at its midpoint A will be: P - 8 in 16 in 12 in 12 in
The lever must exert a force of P = 3800 Ibs at B as shown. The lever lengths are a = 11 in. and b = 47 in. The allowable bending stress for the lever is 12600 psi. If the lever height h is to be 3.5 times the lever thickness t (i.e., h/t = 3.5), what is the minimum thickness t that can be used for the lever? h Cross section Lever a Answer: t = i in.
find the value of El such that the maximum deflection does not exceed 5mm 135 kN 90 kN 2 m 0.7 m 1 m 25 kN/m A AB C AD Rp=192.1 kN Rp= 100.4 kN
A simply supported beam with a length of 4m is loaded with a uniform distributed load (w). The beam has a rectangular hollow section with the following dimensions: Outer Base = 150 mm OuterDepth 200 mm Inner Base = 100 mm Depth = 150 mm Inner Determine the maximum uniformly distributed load which can be applied over the entire length of the beam if the bending stress is limited to 8 Mpa. Please answer with solution and fbd. Thank you.