A compound steel [G= 94 GPa] shaft consists of solid 28-mm-diameter segments (1) and (3) and tube segment (2), which has an outside diameter of 68 mm and an inside diameter of 63 mm. Assume L₁=0.2 m, L₂=2.2 m, L3-0.2 m and T=210 N-m. Determine: (a) the maximum shear stress T₂ in tube segment (2). (b) the angle of twist ₂ in tube segment (2). (c) the rotation angle DIA of gear D relative to gear A. T Answers: (1) (a) T₂ = (b) 4₂ (c) DIA = = Mi B Mi i L2 (2) MPa. C L3 (3) T D

A compound steel [G= 94 GPa] shaft consists of solid 28-mm-diameter segments (1) and (3) and tube segment (2), which has an outside diameter of 68 mm and an inside diameter of 63 mm. Assume L₁=0.2 m, L₂=2.2 m, L3-0.2 m and T=210 N-m. Determine: (a) the maximum shear stress T₂ in tube segment (2). (b) the angle of twist ₂ in tube segment (2). (c) the rotation angle DIA of gear D relative to gear A. T Answers: (1) (a) T₂ = (b) 4₂ (c) DIA = = Mi B Mi i L2 (2) MPa. C L3 (3) T D

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.5P: The propeller shaft of a large ship has an outside diameter 18 in. and inside diameter 12 in,, as...

See similar textbooks

Similar questions

The propeller shaft of a large ship has an outside diameter 18 in. and inside diameter 12 in,, as shown in the figure. The shaft is rated for a maximum shear stress of 4500 psi. If the shaft is turning at 100 rpm, what is the maximum horsepower that can be transmitted without exceeding the allowable stress? If the rotational speed of the shaft is doubled but the power requirements remain unchanged, what happens to the shear stress in the shaft?
1. The 12 kN m torque is applied to the free end of the 6-m steel shaft. The angle of rotation of the shaft is to be limited to 3°. (a) Find the diameter d of the smallest shaft that can be used. (b) What will be the maximum shear stress in the shaft? Use G = 83 GPa for steel. 2. The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque T that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel. 75 mm 50 mm A Bronze B Steel
3. A solid shaft is shown below. If d= 100 mm, / = 1 m, Me = 2n kN-m, and the allowable shear stress of the material is [ t]= 40 MPa. (a) determine the maximum shear stress and check the strength of the shaft; (b) if OC = d/4, determine the shear stress of point C. it •C B M.
100 kip 10 kip -ft The 4-in. diameter shaft shown above is made from a ductile brass alloy. Which of the following are closest to the principal stresses in the shaft? O01 = 31.8 ksi 02 = 76.4 ksi O 01 = 94.0 ksi 02=-62.1 ksi O 01 = 14.3 ksi %3D 02 = -6.37 ksi O o1 = 7.96 ksi !! 02 = 9.55 ksi
The motor shown supplies 126 hp at 1340 rpm at A. Shafts (1) and (2) are each solid 1.86-in.-diameter steel [G=11400 ksi] shafts with lengths of L₁ = 79 in. and L₂=105 in., respectively. Assume Ng-27 teeth and N-42 teeth. The bearings shown permit free rotation of the shafts. (a) Determine the maximum shear stresses T₁, T2 produced in shafts (1) and (2). (b) Determine the rotation angle D/A of gear D with respect to flange A. Answers: (a) T₁ = (b) P DIA Nc WWAMACOM Save for Later C 9.3808 = i 2.1378 eTextbook and Media NB L₁ B D TD ksi, 1₂: = i 14.5924 ksi. Attempts: 1 of 5 used Submit Answer
1. A circular shaft with a keyway can be approximated by the section shown in Fig. r=b Ay r r=2acose Figure 1: Circular shaft with a keyway. The keyway is represented by the boundary equation r = b and the shaft is represented by the boundary equation r = 2a cos 0. Show that using a Prandtl stress function of the form ²) (₁ (1-2a cos) X v = K (b² − ²) (1 – : will solve the problem of torsion on this shaft and find the constant K (assume an applied torque T). Compute the shear stress components Txz and Tyz. (Hint: start by converting the stress function to Cartesian coordinates).
The motor shown supplies 126 hp at 1340 rpm at A. Shafts (1) and (2) are each solid 1.86-in.-diameter steel [G=11400 ksi] shafts with lengths of L₁ = 79 in. and L₂ = 105 in., respectively. Assume Ng-27 teeth and N-42 teeth. The bearings shown permit free rotation of the shafts. (a) Determine the maximum shear stresses T₁, T2 produced in shafts (1) and (2). (b) Determine the rotation angle DA of gear D with respect to flange A. Answers: (a) T₁ = (b) P DIA Nc WWAMACOM Save for Later C 9.3808 = i 2.1378 e Textbook and Media NB L₁ B D TD ksi, 1₂: = i 14.5924 ksi. Attempts: 1 of 5 used Submit Answer
A compound shaft consists of an aluminum tube (1) securely jointed to a steel tube (2). Both aluminum and steel tubes have an outside diameter of D= 48 mm and a wall thickness of t= 3 mm. The shaft is secured by a fixed support at one end and is subjected to a torque of T= 115 N.m at the other end. Determine the maximum stress in the shaft.[L1 = 200 mm, L2 = 350 mm, D = 48 mm , t = 3 mm, G = 75 GPa]
100 kip 10 kip ft The 4-in. diameter shaft shown above is made from a ductile brass alloy. Which of the following are closest to the principal stresses in the shaft? 01 = 31.8 ksi 02 = 76.4 ksi = 94.0 ksi 02 = -62.1 ksi O0g - 14.3 ksi 02 = -6.37 ksi Oo= 7.96 ksi 02 = 9.55 ksi
The motor shown supplies 126 hp at 1340 rpm at A. Shafts (1) and (2) are each solid 1.86-in.-diameter steel [G= 11400 ksi] shafts with lengths of L₁ = 79 in. and L₂ = 105 in., respectively. Assume Ng-27 teeth and Nc-42 teeth. The bearings shown permit free rotation of the shafts. (a) Determine the maximum shear stresses T₁, T2 produced in shafts (1) and (2). (b) Determine the rotation angle DIA of gear D with respect to flange A. Answers: (a) T₁ (b) DIA = = i A i (1) Nc C L1 NB B GE (2) D ksi, T₂ = TD Mi L2 ksi.
A compound steel shaft consists of solid 21-mm-diameter segments (1) and (3) and tube segment (2), which has an outside diameter of 42 mm and a wall thickness of 2.3 mm. Assume T = 350 N·m, L1 = 1.4 m, L2 = 1.5 m, and L3 = 1.4 m. Calculate the polar moment of inertia for tube segment (2). Determine the maximum shear stress in tube segment (2).
1- The shaft shown in the below Fig. consists of a 75-mm diameter aluminum segment rigidly joined to a 50-mm diameter steel segment. The ends of the shaft are attached to rigid supports. Calculate the maximum shear stress developed in each segment when the torque T = 1130 N.m. is applied. Use G = 28 GPa for aluminum and G = 83 GPa for steel. %3D %3D Aluminum Steel 75 mm diameter 50 mm diameter 1130 N.m Tal 1st 2 m 1 m